LENCO AUTO GLIDE BOAT LEVELING SYSTEM F/ DUAL ACTUATOR
Free Shipping Special Product
LENCO AUTO GLIDE BOAT LEVELING SYSTEM F/ DUAL ACTUATOR PRODUCT DESCRIPTIONA Real Automatic Boat Control / Trim Tab Control System that actually works - completely & automatically!
The Auto Glide system controls your trim tabs from the time you leave your dock until you come home again!
The Auto Glide uses engine data and GPS data (depending on your installation method) to drive your boat to the most efficient running angle by adjusting your Lenco trim tabs as needed. This optimum running angle is determined during the set-up process after the installation of your Auto Glide system.
Imagine that your boat's running angle is measured 25 times per second and this data is used by the new Auto Glide control box to:
- Automatically put your boat in the most efficient running angle.
- Reduce the amount of bow rise of your boat during hole shot mode.
- Eliminate bow porpoising (bow bounce).
- Keep your boat level at all times.
These actions will result in a smoother ride and the best possible fuel efficiency.
The Auto Glide has 3 automatic operational modes, 4 automatic settings, and 2 manual operational modes. Although you will most likely keep your Auto Glide in automatic mode, you may immediately convert to manual mode simply by pressing one of the 4 up/down buttons on the key pad.
The main components are the Auto Glide Key Pad, the Auto Glide Control Box , the Control Box Main Harness, and various cables. These cables connect the Auto Glide system to your engine(s), to your GPS unit, your network, and/or a Stand Alone GPS Antenna/Receiver.
Boat must have Lenco Dual Trim Tab System with Lenco Electric Actuators. This is a MUST in all applications.
For Aftermarket Systems:
- The Lenco Glide System will work on ALL boats with ALL engines. GPS data is used to provide data to control box. Optional connection to NMEA 2000 Network is included.For OEM System:
For OEM System:
- Connection to analog systems is available.
- Connection to CANbus-based engines is available. See list below.
- Boat must have NMEA 2000 GPS network or NMEA 2000 antenna receiver.
- NMEA 0183 will work, but will have slower signal response. Lenco offers a NMEA 2000 GPS antenna receiver and optional stainless steel mounting bracket.
1 30254-001D Auto Glide Key Pad Control
1 30256-001 Auto Glide Control Box f/ Dual Actuator
1 30247-001 Auto Glide Control Box Harness f/ Dual Actuator
1 30259-001D CAN bus #1 NMEA2000 Cable - 2.5'
1 30262-001D CAN bus #2 GPS/NMEA 2000 Network Adapter Cable - 2.5'
1 30266-001 NMEA 2000 GPS Antenna Only
3 30267-001D Tee Connector Only
2 30268-001D Terminating Resistor - Female
1 30268-002D Terminating Resistor - Male
1 30281-001D Power Cable - NMEA 2000 Network 2.5'
Available for these CANbus-based engines:
- Yamaha (Command Link Plus requires NMEA 2000 / Yamaha Gateway P/N:6Y98A2D00000)
- Volvo Penta (Non-EVC Engines) (With a Volvo NMEA2000 Gateway - Volvo P/N 3889757)
- Volvo Penta (EVC Engines)
- Detroit Diesel
- John Deere
- Mercury - Verado
- Mercury - Optimax with SmartCraft ECU
- Mercruiser with SmartCraft ECU
- Cummins/Mercruiser w/ SmartCraft ECU
WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
Lenco's Auto Glide Trim Tab Kit (15501-101). For double actuators. Lenco Marine is a true industry leader in maritime and shipbuilding, not only manufacturing decorative sheets, but also...
Lenco Auto Glide Boat Leveling System f/ Dual Actuator Tab Systems Related ProductsLENCO AUTO GLIDE ADAPTER CABLE F/ SMARTCRAFT/MECURY 2.5'
LENCO AUTO GLIDE ADAPTER CABLE F/ COMMAND LINK/YAMAHA 2.5'
LENCO AUTO GLIDE ADAPTER CABLE F/ J1939 2.5'
LENCO AUTO GLIDE ADAPTER CABLE CAN BUS #1 NMEA200 2.5'
LENCO AUTO GLIDE ADAPTER CABLE CAN BUS #2 NMEA 2000 GPS CABLE
LENCO AUTO GLIDE ADAPTER EXTENSION CABLE 10'
LENCO AUTO GLIDE ADAPTER EXTENSION CABLE 20'
LENCO AUTO GLIDE ADAPTER EXTENSION CABLE 30'
LENCO AUTO GLIDE ADAPTER EXTENSION CABLE 40'
LENCO AUTO GLIDE ADAPTER EXTENSION CABLE 50'
Save $54 when you buy the LENCO AUTO GLIDE BOAT LEVELING SYSTEM F/ DUAL ACTUATOR for only $1345 from NVN Marine! Same day free shipping before 3pm.
LENCO AUTO GLIDE BOAT LEVELING SYSTEM F/ DUAL ACTUATOR VIDEOS
LENCO AUTO GLIDE BOAT LEVELING SYSTEM F/ DUAL ACTUATOR USER REVIEWS
LENCO AUTO GLIDE BOAT LEVELING SYSTEM F/ DUAL ACTUATOR SHIPPING & RETURN
- To ensure a fast and safe delivery we use UPS and FedEx Ground/Air shipping services.
- Available shipping methods may vary for different type of products and shipping destinations.
- We ALWAYS ship to the address given by the customer unless you tell us before your order is placed.
- Shipping to the PO BOX is not allowed! Your order will not be fulfilled.
- We are following carriers informations, if carrier delivery status is delivered, we will accept order as a delivered, lost packages are the responsibility of the client.
- Returns will ONLY be accepted within 30 days of the purchase.
Our Shipping Rates and Delivery Times for United States (48 state)
|Free Shipping (500$+ orders)||2-7 Days||Free|
|Best Way Shipping||2-7 Days||$8.95|
|Ground Shipping||1-6 Days||$9.95|
|2nd Day [Promo]||2 Days||$16.95|