Shop Weld Mount, mount without drilling holes. Weld Mount adhesive-bonded fasteners, cable tie mounts, and standoffs attach securely to your hull and surfaces with adhesive, no drilling, so you can route wiring and mount hardware cleanly without piercing the structure. Secure mounting without drilling Drilling holes to mount wiring and hardware means piercing the hull or structure, which you often want to avoid, and Weld Mount solves it. Weld Mount adhesive-bonded fasteners, cable tie mounts, standoffs, and studs bond to the surface with strong adhesive, holding securely without a single hole. That lets you route and secure wiring bundles, mount panels and components, and add hardware cleanly, with no drilling into the hull, tanks, or finished surfaces. For boaters and...
8040 Acrylic Adhesive with Plunger CANNOT SHIP AIR - UPS GROUND ONLYAT-8040 is a good general purpose adhesive packaged in a manual plunger cartridge. Simply snip off the two...
Acrylic AdhesiveCAN NOT SHIP AIR,UPS GROUND ONLYAT-6030 is a 10 to 1 metal bonding adhesive. It has high viscosity and cures in 10 - 12 minutes, has a...
Acrylic AdhesiveCAN NOT SHIP AIR,UPS GROUND ONLYAT-4020 is a specially formulated adhesive for holding all our parts with little or no sagging in vertical or overhead applications. Cures...
AT-850 Square Mixing Tip f/2010, 4020, & 8040 Adhesives - 4" - Case of 10Weld Mount's AT-850 tip is for use only with the 2010, 4020, & 8040...
Aluminum Wire TieUsed with Stainless Steel or Nylon wire ties up to 0.4 inches wide. 250 lbs tensile strength when bonded with AT-6030 adhesive manufactured of 5052 marine...
No Slide Metal/Composite BonderRevolutionary Metal Bonder will hold heavy parts at application without sliding either on a vertical or overhead surface. AT-8040 will hold 3,500lbs in 40 minutes....
Black Nylon Wire Tie MountThe AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's...
Acrylic AdhesiveCAN NOT SHIP AIR,UPS GROUND ONLYAT-2010 is our biggest seller and is a unique adhesive. It has high viscosity and will hold smaller parts without sagging. AT-2010...
Black Nylon Wire Tie MountThe AT-3 tie mount is smaller for panel and other small space applications. This part is molded in black nylon and is sized for...
Black Nylon Wire Tie MountThe AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's...
AT-5B Large Black Nylon Wire Tie Mount - Qty. 500The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded...
AT-850 Square Mixing Tip 4" - Case of 50Weld Mount's AT-850 tip is for use only with the 2010, 4010, & 8040 adhesives. It's unique design eliminates any...
White Nylon Wire Tie MountThe AT-3 tie mount is smaller for panel and other small space applications. This part is molded in white nylon and is sized for...
Adhesive Dispensing GunThe AT-300 Adhesive dispensing gun has a 1:1 plunger for use with AT-2010 and AT-4020 50ml cartridges. When using AT-6030 adhesive it requires AT-12 (10 to...
Retail Wire Tie KitCAN NOT SHIP AIR, UPS GROUND ONLYThe AT-1050 kit contains one manual mix tube of AT-8040 adhesive and 25 pc. AT-5 white wire tie mount....
1" Tall Stainless Stud w/#8 x 32 ThreadOur Small Stainless Steel Panel Studs have a wide range of uses. Originally they were used for mounting on the backside...
Footman's Strap MountThe Footman's Strap Mount is designed to be bonded with AT-4020 Acrylic Adhesive. This strap mount is 3.25" long and 1" wide and holds up to...
White Nylon Wire Tie MountThe AT-3 tie mount is smaller for panel and other small space applications. This part is molded in white nylon and is sized for...
White Nylon Wire Tie MountThe AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's...
White Nylon Wire Tie MountThe AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's...
.75" Tall Stainless Stud w/#10 x 24 ThreadUtilize the same base as the 1.4" x 20 studs but with a smaller threaded stud inserted into the base. These...
Adhesive Dispensing Gun with 10:1 Plunger for AT-6030 Adhesive OnlyThe AT- 301 Adhesive Dispensing Gun Is Designed Specifically For Use With Our AT-6030 38 ml 10:1 Adhesive Cartridge....
10:1 Gun Plunger for AT-6030 AdhesiveSingle Pack gun plunger for AT-6030 Adhesive Welding Installation System 8013 Fastener 10:1 Spray Gun Plunger for AT-6030 Adhesive Single Gun Plunger for...
Executive Fastener Kit - No AdhesiveThis Kit Contains A Large Selection Of All The Common Weld Mount Parts And Is An Ideal Kit For The Full Service Yard...
Shop Weld Mount, mount without drilling holes. Weld Mount adhesive-bonded fasteners, cable tie mounts, and standoffs attach securely to your hull and surfaces with adhesive, no drilling, so you can route wiring and mount hardware cleanly without piercing the structure.
Drilling holes to mount wiring and hardware means piercing the hull or structure, which you often want to avoid, and Weld Mount solves it. Weld Mount adhesive-bonded fasteners, cable tie mounts, standoffs, and studs bond to the surface with strong adhesive, holding securely without a single hole. That lets you route and secure wiring bundles, mount panels and components, and add hardware cleanly, with no drilling into the hull, tanks, or finished surfaces. For boaters and installers rigging electrical, plumbing, and equipment, Weld Mount makes a tidy, secure installation possible where drilling is undesirable or impossible. It is a go-to for clean, no-hole mounting aboard.
Choosing the right product comes down to the job and the load. Match the mount type, cable tie mount for wiring bundles, standoff or stud for hardware and panels, to what you are securing. Use the recommended adhesive for the surface and a strong bond, and prepare the surface properly, since adhesive mounts rely on good prep to hold. Confirm the mount and adhesive suit the load and the surface material. Review the product details and the bonding instructions before use. With Weld Mount fasteners, you mount wiring and hardware securely and cleanly without drilling.
Weld Mount fasteners bond to the surface with a strong adhesive rather than screws or rivets, so they mount securely without drilling any holes. That lets you secure wiring and hardware without piercing the hull, tanks, or finished surfaces.
Drilling holes pierces the hull, tank, or finished surface, which can risk leaks, weaken structure, or mar the finish. Adhesive mounts avoid that, giving a clean, secure installation with no holes, which is ideal for wiring and hardware on a boat.
Yes, very much. Adhesive mounts rely on a good bond, so clean and prepare the surface properly per the instructions before bonding, and use the recommended adhesive for the surface. Good prep is the difference between a mount that holds and one that fails.
