Shop Weld Mount, mount without drilling holes. Weld Mount adhesive-bonded fasteners, cable tie mounts, and standoffs attach securely to your hull and surfaces with adhesive, no drilling, so you can route wiring and mount hardware cleanly without piercing the structure. Secure mounting without drilling Drilling holes to mount wiring and hardware means piercing the hull or structure, which you often want to avoid, and Weld Mount solves it. Weld Mount adhesive-bonded fasteners, cable tie mounts, standoffs, and studs bond to the surface with strong adhesive, holding securely without a single hole. That lets you route and secure wiring bundles, mount panels and components, and add hardware cleanly, with no drilling into the hull, tanks, or finished surfaces. For boaters and...
1.75" Tall Stainless Stud with 1/4" x 20 ThreadMounts to virtually any surface using the AT-4010 Acrylic Adhesive. This is a structural part with 500 lbs. of tensile...
2.25" Tall Stainless Stud w/#10 x 24 ThreadUtilize the same base as the 1.4" x 20 studs but with a smaller threaded stud inserted into the base. These...
1.5" Tall Stainless Stud w/#10 x 24 ThreadUtilize the same base as the 1.4" x 20 studs but with a smaller threaded stud inserted into the base. These...
1.25" Tall Stainless Stud w/#10 x 24 ThreadUtilize the same base as the 1.4" x 20 studs but with a smaller threaded stud inserted into the base. These...
1.5" Tall Stainless Stud w/#8 x 32 ThreadOur Small Stainless Steel Panel Studs have a wide range of uses. Originally they were used for mounting on the backside...
1.25" Tall Stainless Stud w/#8 x 32 ThreadOur Small Stainless Steel Panel Studs have a wide range of uses. Originally they were used for mounting on the backside...
.75" Tall Stainless Stud w/#8 x 32 ThreadOur Small Stainless Steel Panel Studs have a wide range of uses. Originally they were used for mounting on the backside...
Black Nylon Wire Tie MountThe AT-3 tie mount is smaller for panel and other small space applications. This part is molded in black nylon and is sized for...
Adhesive Mixing Tip For AT-6030Our AT-650 mixing tip is designed specifically for use with our AT-6030 adhesive. AT-6030 is a 10 to 1 adhesive which requires a mixing...
Adhesive Mixing Tip For AT-6030Our AT-650 mixing tip is designed specifically for use with our AT-6030 adhesive. AT-6030 is a 10 to 1 adhesive which requires a mixing...
Dual Pusher RodThe AT-500 dual pusher rod is used to dispense equal amounts of our AT-2010 or AT-4020 adhesive for manual mixing. This dual pusher rod can not...
Shop Weld Mount, mount without drilling holes. Weld Mount adhesive-bonded fasteners, cable tie mounts, and standoffs attach securely to your hull and surfaces with adhesive, no drilling, so you can route wiring and mount hardware cleanly without piercing the structure.
Drilling holes to mount wiring and hardware means piercing the hull or structure, which you often want to avoid, and Weld Mount solves it. Weld Mount adhesive-bonded fasteners, cable tie mounts, standoffs, and studs bond to the surface with strong adhesive, holding securely without a single hole. That lets you route and secure wiring bundles, mount panels and components, and add hardware cleanly, with no drilling into the hull, tanks, or finished surfaces. For boaters and installers rigging electrical, plumbing, and equipment, Weld Mount makes a tidy, secure installation possible where drilling is undesirable or impossible. It is a go-to for clean, no-hole mounting aboard.
Choosing the right product comes down to the job and the load. Match the mount type, cable tie mount for wiring bundles, standoff or stud for hardware and panels, to what you are securing. Use the recommended adhesive for the surface and a strong bond, and prepare the surface properly, since adhesive mounts rely on good prep to hold. Confirm the mount and adhesive suit the load and the surface material. Review the product details and the bonding instructions before use. With Weld Mount fasteners, you mount wiring and hardware securely and cleanly without drilling.
Weld Mount fasteners bond to the surface with a strong adhesive rather than screws or rivets, so they mount securely without drilling any holes. That lets you secure wiring and hardware without piercing the hull, tanks, or finished surfaces.
Drilling holes pierces the hull, tank, or finished surface, which can risk leaks, weaken structure, or mar the finish. Adhesive mounts avoid that, giving a clean, secure installation with no holes, which is ideal for wiring and hardware on a boat.
Yes, very much. Adhesive mounts rely on a good bond, so clean and prepare the surface properly per the instructions before bonding, and use the recommended adhesive for the surface. Good prep is the difference between a mount that holds and one that fails.
