NOV 19, 2026 14 min read

HOW TO CHOOSE A TROLLING MOTOR: THRUST, VOLTAGE, SHAFT LENGTH, AND MOUNT

HOW TO CHOOSE A TROLLING MOTOR: THRUST, VOLTAGE, SHAFT LENGTH, AND MOUNT

How to choose a trolling motor: figure your fully loaded boat weight and buy at least 2 lb of thrust for every 100 lb of it. Pick the voltage that thrust needs (12V up to 55 lb, 24V for 70 to 80 lb, 36V for 101 lb and up). Measure from your mount to the waterline and read the maker's shaft chart. Then choose bow or transom mount, freshwater or saltwater, and how you want to steer.

That is the whole job in five decisions. Get thrust and shaft length right and almost any name-brand motor will serve you. Get either one wrong and you will fight the boat all day, no matter how many GPS features you paid for.

Below is how we size motors at the counter, with the numbers from Minn Kota, Garmin and MotorGuide so you can check our math.

Step 1: Size thrust to your loaded boat weight

Thrust is the pushing force of the motor, measured in pounds. It is a static number. More thrust does not mean more top speed. It means more control when wind and current push back.

The rule: Minn Kota recommends at least 2 lb of thrust for every 100 lb of fully loaded boat weight, people and gear included. MotorGuide uses the same 2-per-100 figure and says to add 10 lb of thrust if you often fish strong current or wind.

"Fully loaded" is where people go wrong. Add up all of it:

  • Hull weight (from the builder's spec sheet or capacity plate area)
  • Outboard and kicker
  • Fuel (gasoline runs about 6 lb per gallon)
  • Batteries, including the new trolling motor batteries
  • Every person you fish with
  • Coolers, tackle, ice, anchors

Worked example: a 2,000 lb loaded boat needs (2,000 / 100) x 2 = 40 lb of thrust minimum. That is Minn Kota's own example.

Minn Kota thrust and battery chart

Loaded boat weight Max boat length Minimum thrust Batteries / voltage
1,500 lb or less 14 ft 30 lb 1 (12V)
2,000 lb 17 to 18 ft 40 to 45 lb 1 (12V)
2,500 lb 20 to 21 ft 50 to 55 lb 1 (12V)
3,000 to 3,500 lb 23 ft 70 lb 2 (24V)
4,000 lb 25 ft 80 lb 2 (24V)
4,500 lb or more 25 ft + 101 to 112 lb 3 (36V)

Source: Minn Kota Motor Selection Guide / Boat Size Chart.

Our take: treat the chart as the floor

The chart is built for normal lake conditions. Minn Kota says so. If you fish tidal rivers, open bays or anywhere the wind blows 15 knots by noon, go one step up. A bigger motor run at half speed is quieter and holds position better than a small motor pinned at 100%. Bass Pro makes the same point in its buying guide: a higher-thrust motor runs more efficiently at lower speeds.

The limit: more thrust means more voltage, more batteries and more weight in the boat. On a 14 ft jon boat, a 36V setup is overkill and the extra 100+ lb of lead-acid batteries hurts you.

Step 2: Pick the voltage (and count batteries)

You need one 12V battery for every 12 volts in the system. Minn Kota groups its motors like this:

  • 12V, 1 battery: 55 lb of thrust or less
  • 24V, 2 batteries: 68 to 80 lb
  • 36V, 3 batteries: 101 to 112 lb

Higher voltage moves the same work with less current. Bass Pro gives an example: a 12V motor at 44 lb of thrust may draw 36 amps, while a 24V motor at 54 lb may draw only 28 amps. Less current means less heat in the wire and longer run time per amp-hour.

Before you buy a 24V or 36V motor, check three things:

  1. Space. Do you have room, and a vented compartment, for two or three group 27 or group 31 batteries?
  2. Weight. Lead-acid group 31 batteries are heavy. Lithium (LiFePO4) cuts that weight a lot, but costs more up front. Our Lithium Marine Battery FAQ covers the trade-offs.
  3. Charging. A 24V or 36V bank needs a multi-bank onboard charger with one output per battery, or a charger built for that voltage.

Brushless and dual-voltage motors

The newest motors blur the old voltage lines. Minn Kota's QUEST series runs on 24V or 36V. The Riptide Instinct QUEST makes 90 lb of thrust at 24V and 115 lb at 36V. Minn Kota says its brushless QUEST motors give up to 30% longer run time and 50% more torque than its earlier brushed motors. Garmin's Force Pro uses a brushless motor too.

Brushless costs more. On a boat that fishes hard all day, the run time gain is worth it. On a weekend boat that trolls two hours at a time, a brushed motor will do the job for less money.

Step 3: Measure for shaft length

Shaft length decides whether the prop stays in the water. Too short and the prop breaks the surface in chop. It cavitates, makes noise that spooks fish, and loses thrust. Too long and it may not stow, and it drags through weeds and stumps.

The 12-inch rule: Minn Kota says the top of the motor's lower unit should sit under at least 12 inches of water.

How to measure

  1. Load the boat the way you fish it.
  2. Find the exact spot where the mount will bolt down. Bow height changes across the deck, so measure there, not at the tip of the bow.
  3. Measure straight down from that mounting surface to the waterline.
  4. Add the maker's allowances (below).
  5. Read the result against that maker's chart. Do not use one brand's chart for another brand's motor.

Allowances by brand

  • Minn Kota: add 5 in for rough water. Add 9 in for a bow-mount hand-control motor, plus another 12 in if you steer it standing up.
  • Garmin: add 8 in if you regularly fish in waves.
  • MotorGuide: use a formula instead of a chart. Measure bow to waterline, then add 20 in. Your shaft should be at least that long. An 18 in bow needs a 38 in shaft or longer.

Minn Kota bow-mount shaft chart

Bow to waterline Recommended shaft
0 to 10 in 36 in
16 to 22 in 42 to 45 in
22 to 28 in 48 to 52 in
28 to 44 in 54 to 72 in
45 in + 87 in

Minn Kota transom-mount shaft chart

Transom to waterline Recommended shaft
0 to 10 in 30 in
10 to 16 in 36 in
16 to 22 in 42 in
Over 22 in Consult factory

Source: Minn Kota Motor Selection Guide / Boat Size Chart.

Garmin Force shaft chart

Motor Bow to waterline Recommended shaft
Force / Force Pro 0 to 19 in 50 in
Force / Force Pro 15 to 26 in 57 in
Force Kraken 0 to 19 in 48 in
Force Kraken 15 to 34 in 63 in
Force Kraken 26 to 46 in 75 in
Force Kraken 38 to 61 in 90 in
Force Kraken 53 to 81 in 110 in

Source: Garmin, "How to choose the right trolling motor."

Garmin's ranges overlap. If you land in the overlap, and you ever see chop, take the longer shaft. You can always trim a long shaft up. You cannot make a short one longer.

Step 4: Choose bow mount or transom mount

Bow mount pulls the boat from the front. It steers better, tracks into wind, and is where every GPS anchoring motor lives. It is the right call for bass boats, bay boats, center consoles and most boats over 16 ft.

Transom mount clamps on the back. It is cheaper, simpler and fine for jon boats, small skiffs, canoes and kayaks. It pushes rather than pulls, so it wanders more in a crosswind.

Engine mount motors bolt to the outboard's cavitation plate. Minn Kota's engine-mount guide calls for at least 13 in from cavitation plate to waterline, and a plate at least 4.5 in long and 6 in wide. Check your outboard before you order one.

For bow mounts, measure the deck before you buy. A high-freeboard center console with a tight bow may need a long-shaft motor built for it, like the Garmin Force Kraken 75 in. Garmin built the Kraken for boats with higher freeboard and limited bow space, such as bay boats and center consoles.

Step 5: Freshwater or saltwater

Buy a saltwater model if your boat ever sees salt or brackish water. No exceptions. Saltwater motors use sealed electronics, corrosion-resistant hardware and a sacrificial anode. Minn Kota's saltwater line is Riptide. Garmin's Force Kraken is rated for salt and fresh.

A freshwater motor run in the Intracoastal or a tidal creek is not built for that water. Pay the price gap up front.

Step 6: Pick your steering and control

Control type How it works Best for Limitation
Hand control (tiller) You steer with the handle Transom motors, small boats Ties up one hand
Cable steer Foot pedal moves a cable to the head Anglers who want direct feel No GPS anchoring
Electric steer Pedal or remote drives a steering motor GPS features, hands-free fishing More cost, more draw

Electric steer opens up GPS anchoring. Minn Kota calls it Spot-Lock. On QUEST motors, Jog moves the lock point 5 ft in any direction. If you fish structure in wind or current, GPS anchoring is the feature you will use most. It also costs battery. Holding against a 2-knot current all morning takes real amp-hours, so size your bank for it.

If you run a Garmin Force and want pedal control, or need a replacement, we stock the Garmin Force foot pedal. Check what comes in the box with your motor before you order.

Step 7: Plan the wiring before the motor shows up

This is where installs go bad. A trolling motor pulls 40 to 60 amps at full power. Undersized wire drops voltage, gets hot and cuts your thrust.

  • Protect the circuit. Minn Kota says an over-current device (circuit breaker or fuse) must be used, and cites the Coast Guard rule that each ungrounded current-carrying conductor needs a manually reset, trip-free breaker or fuse.
  • Mount it close. Install the breaker on the positive lead as close to the batteries as you can.
  • Size the breaker to the motor. Minn Kota lists 60 A for 50 to 55 lb (12V) and 80 lb (24V) motors, and 50 A for 40 to 45 lb (12V) and 70 lb (24V) motors.
  • Size the wire to the run. Minn Kota's table assumes no more than 3% voltage drop at full power.

Minn Kota wire gauge for extension runs

Motor Max amp draw Breaker 10 ft run 20 ft run
40 / 45 lb (12V) 42 A 50 A 6 AWG 2 AWG
50 / 55 lb (12V) 50 A 60 A 4 AWG 2 AWG
70 lb (24V) 42 A 50 A 8 AWG 6 AWG
80 lb (24V) 56 A 60 A 6 AWG 4 AWG
112 lb (36V) 52 A 60 A 8 AWG 6 AWG

Source: Minn Kota Trolling Motor Wiring and Battery Guide. Wire extension length is battery to motor leads.

Look at the 12V rows. A 55 lb motor at the bow of a 20 ft boat needs 2 AWG wire. That is one more reason bigger boats go to 24V. Minn Kota also recommends ABYC standards and a qualified marine tech for rewiring. We agree. We are ABYC certified, and we install what we sell.

Three real-world setups

16 ft aluminum boat, freshwater lakes

Loaded weight about 1,800 lb. The rule says 36 lb minimum. Buy a 45 or 55 lb, 12V bow mount. If your bow measures 16 to 22 in to the waterline, Minn Kota's chart says a 42 to 45 in shaft. One group 27 or 31 battery.

18 to 20 ft bay boat, inshore saltwater

Loaded weight around 3,000 lb. Chart says 70 lb at 24V. Wind and tide say go to 80 lb. If your bow measures 22 to 28 in, Minn Kota's chart puts you at a 48 to 52 in shaft, and longer if you add for rough water. The Minn Kota Riptide SF 80 (24V, 80 lb, 62 in) is a cable-steer option for that boat. For a smaller saltwater skiff on 12V, look at the Minn Kota Riptide SM 55 lb (12V, 42 in).

23 ft + center console, tall bow

Loaded weight 4,500 lb or more. You need 101 lb or more at 36V, or a dual-voltage brushless motor. On a tall bow, measure carefully. A 40 in bow-to-waterline reading lands in Garmin's 75 in and 90 in Kraken rows. Long shafts flex in a head sea. A stabilizer like the RAM Mount trolling motor stabilizer with long arm keeps a stowed motor from slamming on the trailer and in chop.

Common mistakes we see

  • Sizing to dry hull weight. Size to loaded weight. Always.
  • Measuring at the point of the bow. Measure where the mount sits.
  • Reusing old 10 AWG wire. Check the gauge table. Old wire is often too small for a new, bigger motor.
  • Skipping the breaker. It is required, and it is cheap.
  • Freshwater motor, salt boat. Pay for the saltwater model once.
  • Forgetting sonar. Many motors take a trolling motor transducer in the nose cone. Plan your fish finder at the same time. See our guide to choosing a fish finder transducer.

Frequently asked questions

How much thrust do I need for my boat?

Use at least 2 lb of thrust for every 100 lb of fully loaded boat weight, per Minn Kota and MotorGuide. A 2,000 lb loaded boat needs 40 lb minimum. Add more if you fish wind or current.

What size trolling motor for a 16 ft boat?

Many 16 ft boats weigh 1,500 to 2,000 lb loaded, so 40 to 55 lb of thrust on 12V works. Minn Kota's chart puts boats up to 17 to 18 ft and 2,000 lb at 40 to 45 lb.

Is 24V better than 12V?

For boats over about 2,500 lb loaded, yes. 24V gives you 70 to 80 lb of thrust with lower current draw, which means smaller wire and longer run time. It needs two batteries instead of one.

How do I measure trolling motor shaft length?

Measure straight down from the mounting surface to the waterline with the boat loaded. Add the maker's allowance for rough water, then read that maker's chart. MotorGuide's rule is bow to waterline plus 20 inches.

Is a longer shaft better?

Up to a point. A longer shaft keeps the prop in the water in chop, and you can trim it up. Too long and it may not stow cleanly or will drag in shallow water. When in doubt between two sizes, go longer.

Can I use a freshwater trolling motor in saltwater?

No. Saltwater motors have sealed electronics, corrosion-resistant hardware and a sacrificial anode. A freshwater motor in salt will corrode.

What size circuit breaker does a trolling motor need?

It depends on the motor. Minn Kota specs 60 A for 50 to 55 lb (12V) and 80 lb (24V) motors, and 50 A for 40 to 45 lb (12V) and 70 lb (24V) motors. Mount it on the positive lead near the battery.

Are brushless trolling motors worth it?

If you fish long days, yes. Minn Kota says its brushless QUEST motors deliver up to 30% longer run time and 50% more torque than its earlier brushed motors. For short trips, brushed motors cost less and work fine.

Sources

Not sure what fits your boat? Send us your boat's make, length and bow-to-waterline measurement. We'll tell you the thrust, voltage and shaft that fit, and what it takes to wire it right.