Maretron turns your NMEA 2000 network into a full vessel monitoring system. Add the sensors you need, wire a clean backbone, and watch the whole boat from one display. Maretron builds the sensors, monitors, and cables that turn an NMEA 2000 network into a complete vessel monitoring system. Instead of guessing, you can watch tank levels, temperatures, battery and AC status, bilge water, and gas detection from a single display. This collection covers Maretron sensors, monitoring modules, network cables, and connectors. Building it right comes down to choosing the sensors you need and wiring a solid network. Pick the sensors that matter Maretron offers a wide sensor range: tank level monitors for fuel, water, and waste, temperature and pressure probes,...
Maretron NMNB1NF080 Attributes Mini Double-Ended Cordset - M to F - 8m (blue) - Double-ended cordsets are used for trunk or drop lines and make for a secure...
Mid Single-Ended Cordset - Female to Open Pigtail - 25 Meter (blue)- This 25 meter length Mid size cable with a Micro female connector on one end is...
The new MPower Series by Maretron replaces standard mechanical circuit breakers and switches with state-of-the-art digital power distribution. Customers looking to achieve the power and convenience of advanced...
NMEA 2000 Starter Kit 2 Maretron's deluxe starter kit provides all the necessary cables and connectors necessary to connect two products together on an NMEA 2000® network. Contacts...
NMEA 2000 Starter Kit 1Maretron's deluxe starter kit provides all the necessary cables and connectors necessary to connect two products together on an NMEA 2000® network. Contacts are...
Maretron NMEA 2000 Starter KitBuilding a New NMEA 2000 Network onboard? Save when buying this Maretron NMEA 2000 Starter Kit. Everything you need for a basic NMEA 2000...
Mid Bulk Cable - 20M ContinuousMid bulk cable is primarily used as drop cable, but it can also be used at the trunk line depending on network power...
This NMEA 2000 Magnetic Switch Cylinder (Indoor/Outdoor) is an available SIM100 Accessory.Maretron MS1055N Attributes Magnetic Switch, MFG# MS-1055-N, Cylinder type for Indoor/Outdoor use. Includes magnet. For use with...
Maretron PTS05PSI01 Attributes Submersible Pressure Transducer - 0 to 5 PSIThe submersible pressure transducers are used together with Maretron's Fluid Pressure Monitor (FPM100), whichallows tank fluid level to...
Micro Double-Ended Cordset - 3M - *Case of 6*Mechanical Contact Carrier Mat/Color: Thermoplastic PUR/Blue-Gray Molded Body Mat/Color: Thermoplastic PUR/Blue-Gray Contact Mat/Plating: Brass/Gold Coupling Nut Mat/Plating: Brass/Nickel Connector Outside...
Mini Double-Ended Cordset - M to F - .5m (gray) - Double-ended cordsets are used for trunk or drop lines and make for a secure connection and simple...
Maretron Fluid Pressure Sensor Transducers work with the Maretron FMP100 which will adapt up to six pressure Transducers to the NMEA 2000 networkPressure Transducer 0 to 50 PSIAll...
Mini Double-Ended Cordset - M to F - 10m (blue) - Double-ended cordsets are used for trunk or drop lines and make for a secure connection and simple...
Mini Double-Ended Cordset - M to F - 5m (blue) - Double-ended cordsets are used for trunk or drop lines and make for a secure connection and simple...
This IS216 Motion Detector is an available accessory for the NMEA 2000 Switch Indicator Module SIM100-01.Maretron IS216 Attributes Motion Detector for SIM100Passive Infrared Motion Detector (PIR)Attaches to Maretron...
The IRHT-01 Indoor Humidity/Temperature sensor measures relative humidity and air temperature and transmits them via two 4-20mA current loop interfaces. The IRHT-01 is used in conjunction with Maretron's...
Maretron's CLM100 converts commercially available 4-20mA current loop Transducers into digital data so a wide variety of information can be displayed on compatible NMEA 2000 displays. Numerous 4-20mA...
Solid-State Rate/Gyro Compass w/10m Cable & ConnectorMaretron's SSC300, implementing the second generation of Maretron's award-wining compass technology, is a solid state, rate gyro electronic compass that provides better...
Solid-State Rate/Gyro Compass without CablesMaretron's SSC300, implementing the second generation of Maretron's award-wining compass technology, is a solid state, rate gyro electronic compass that provides better than 0.7x...
When fluid passes through the sensor, the internal rotors turn. Magnets which are located in the rotors will pass across sensors in the sensor circuit board. Pulses from...
When fluid passes through the sensor, the internal rotors turn. Magnets which are located in the rotors will pass across sensors in the sensor circuit board. Pulses from...
When fluid passes through the sensor, the internal rotors turn. Magnets which are located in the rotors will pass across sensors in the sensor circuit board. Pulses from...
When fluid passes through the sensor, the internal rotors turn. Magnets which are located in the rotors will pass across sensors in the sensor circuit board. Pulses from...
The ESL 500N Series conventional 2-wire and 4-wire photoelectric smoke detectors have intelligent software and digitally processed sensing capabilities. This intelligence coupled with the ESL patented optical sensing...
Maretron turns your NMEA 2000 network into a full vessel monitoring system. Add the sensors you need, wire a clean backbone, and watch the whole boat from one display.
Maretron builds the sensors, monitors, and cables that turn an NMEA 2000 network into a complete vessel monitoring system. Instead of guessing, you can watch tank levels, temperatures, battery and AC status, bilge water, and gas detection from a single display. This collection covers Maretron sensors, monitoring modules, network cables, and connectors. Building it right comes down to choosing the sensors you need and wiring a solid network.
Maretron offers a wide sensor range: tank level monitors for fuel, water, and waste, temperature and pressure probes, AC and DC monitors that track voltage, current, and battery state, bilge and high-water detectors, and carbon monoxide and smoke detection. Start with what you most want to know, often fuel and water levels, battery health, and bilge status, then expand the system over time.
Maretron sensors report over NMEA 2000, so they share data with your chartplotter and any compatible display. Build the network with a proper backbone, drop cables to each device, terminators at both ends, and a power tap sized for the load. A clean, correctly terminated backbone is the difference between reliable data and a network that drops out.
Maretron uses field-attachable and molded NMEA 2000 cables and connectors in mid and micro sizes. Measure your runs, use the right cable length and gender, and add tees where devices branch off. Quality cabling keeps the network solid in a wet, vibrating environment.
A Maretron display like the DSM series, or any compatible NMEA 2000 screen, shows the data and can alarm on conditions you set, like high bilge water or low voltage. Alarms are the real payoff, because catching a problem early at the dock beats discovering it underway.
One advantage of a networked system is that you can add sensors as needs grow. Leave room on the backbone and a few spare drops so the next sensor is a plug-in, not a rewire.
Not sure where to start? Tell our techs what you want to monitor and your existing electronics, and we will match the sensors, cables, and display so your boat reports what matters.
Maretron offers sensors for tank levels (fuel, water, waste), temperature and pressure, AC and DC electrical status and battery state, bilge and high-water detection, and carbon monoxide and smoke. You build the system from the sensors that matter to you.
Maretron sensors report over NMEA 2000, so they share data with compatible chartplotters and displays on the same network. Confirm your display supports the data types, and you can read the sensors right on your existing screen.
You need an NMEA 2000 backbone, drop cables to each device, terminators at both ends, and a power tap sized for the load. A clean, correctly terminated backbone is what keeps the data reliable.
A display can alarm on conditions you set, like high bilge water or low battery voltage. Alarms are the real payoff of monitoring, because catching a problem early, ideally at the dock, beats discovering it underway.
Yes. A networked system lets you add sensors as needs grow. Leave room on the backbone and a few spare drops so the next sensor plugs in rather than forcing a rewire.
