Victron Energy VE.Direct to USB Interface Cable, 0.9m
Victron Energy VE.Direct to USB Interface Cable, 0.9m — Product description
The Victron VE.Direct to USB cable is the simple bridge between your Victron gear and a screen. Plug it into the VE.Direct port on a BMV battery monitor or a low-power MPPT charger, and read live data in VictronConnect on a computer or add the device to a Color Control GX. It's 0.9 meters of black cable that does one job and does it reliably.
If you've got a Victron battery monitor or solar charge controller and you want to actually see what it's doing, this is the cable that gets you there. The VE.Direct to USB interface cable plugs into the VE.Direct port on your BMV-700 series monitor or a low-power MPPT charge controller on one end, and into a USB port on the other. From there you can read live data on a computer running VictronConnect, or feed that device into a Color Control GX so it shows up alongside the rest of your system. It's 0.9 meters long, right around three feet, and it's black so it disappears behind the panel.
VE.Direct is Victron's own wired communication port, and it's on nearly every modern Victron device that reports data, from battery monitors to MPPT controllers to inverters. This cable is the bridge from that port to the USB world. That's why one small accessory ends up being the thing you reach for again and again as a system grows.
The most common use is dead simple. You want to check the state of charge on your house bank, or pull a history log off a BMV, and you don't have Bluetooth range or a GX device handy. Plug this into a laptop, open VictronConnect, and the device shows up. You can read voltage, current, consumed amp-hours, and the whole trend history. For a quick diagnostic at the dock, or setting up a new install before the boat's wired for a display, it's the fastest way in.
The other big use is bringing a stray VE.Direct device into a GX system. Say you've got a Color Control GX running the show, but you added a small MPPT or a second battery monitor and you're out of VE.Direct ports on the GX itself. Run this cable from that device into one of the GX's USB ports and it joins the party. Its data lands on the GX screen and pushes up to the VRM portal like everything else. One note from the field. Connect the cable after the GX has fully booted, not before. If you plug it in during startup, the GX sometimes doesn't enumerate it cleanly, and a quick reconnect sorts it out.
On a boat, cable routing matters more than people expect. Nine tenths of a meter isn't a lot of slack, so plan your device placement and your GX or USB hub location accordingly. If your run is longer than the cable reaches, a powered USB extension holds the data signal better than a cheap passive one, especially on a bigger sailboat where the panel and the battery monitor shunt can be a compartment apart. Keep the cable away from engine heat where you can. And on powerboats with a lot of ignition noise, a ferrite choke near the GX end is cheap insurance against EMI creeping into the readings. None of that is required. It's just what keeps a data link solid year after year.
A couple of things to be clear about. This is a data and communication cable, not a power cable. It doesn't charge anything or carry load current. It just carries the VE.Direct serial signal so your gear can talk to a computer or a GX. And if you're wiring more than one VE.Direct device into a single GX over USB, you may need to set instance numbers in the GX menu so each one shows up separately instead of stepping on the other. Takes two minutes once you know where the setting lives.
Setup is about as easy as it gets. On most current computers, VictronConnect handles the USB driver for you when you install the app, so you plug in and go. Older Color Control GX firmware occasionally shows a newly added charger as unknown until you update the GX, so if a device connects but the name looks off, a firmware update on the GX usually clears it. Once it's talking, you don't have to think about it again.
Who needs one? Anyone running Victron gear who wants monitoring without committing to a permanent display, or anyone expanding a GX setup past its built-in VE.Direct ports. It's the same cable whether you're on a 24-foot center console with a single battery monitor or a cruising sailboat with a full Victron power system. Simple part, one job, done reliably. If 0.9 meters is too short for your layout, we also stock longer VE.Direct to USB cables in the same family.
Key Features
- VE.Direct to USB connection reads any VE.Direct device on a computer running VictronConnect
- 0.9 meter (about 3 ft) length keeps the run short and tidy behind the panel
- Works with BMV-700 series battery monitors for live state-of-charge and history logs
- Pairs with low-power MPPT solar charge controllers to pull charging data
- Adds a VE.Direct device to a Color Control GX through its USB port when built-in VE.Direct ports are full
- Data and communication only, so it never carries load or charging current
- Black jacket blends into the electrical panel
- VictronConnect installs the USB driver, so most computers recognize it on plug-in
Why Buy from NVN Marine
- Authorized Victron Energy reseller, full manufacturer warranty
- NMEA member and ABYC certified, advice from real boat techs
- Same-day shipping before 3 PM ET on in-stock items
- NY headquarters and Fort Lauderdale flagship retail store
Technical specifications
| Title | Victron Energy VE.Direct to USB Interface Cable, 0.9m |
|---|---|
| Brand | Victron Energy |
| Manufacturer Part Number | ASS030530209 |
| UPC | 8719076019602 |
| Cable Length | 0.9 m (approx. 3 ft) |
| Color | Black |
| Connection 1 | VE.Direct |
| Connection 2 | USB Type-A |
| Interface Signal | VE.Direct serial data |
| Function | Monitoring and communication interface |
| Product Type | VE.Direct Interface Cable |
| Compatible Devices | BMV-700 series battery monitors, low-power MPPT charge controllers, Color Control GX |
| Keystone Part Number | S030530209 |
Frequently asked questions
What does the VE.Direct to USB cable actually do?
It connects a Victron device's VE.Direct port to a USB port, so you can read that device in VictronConnect on a computer or bring it into a Color Control GX. It carries data, not power.
Which devices work with it?
Any Victron device with a VE.Direct port. The common ones are the BMV-700 series battery monitors and low-power MPPT solar charge controllers, but VE.Direct is on most modern Victron gear that reports data.
How long is the cable?
It's 0.9 meters, right around three feet. If that's too short for your layout, we stock longer VE.Direct to USB cables in the same family.
Does it supply power to my battery monitor or charger?
No. It's a data and communication cable only. Your device still gets its power the way it normally does, and this just carries the VE.Direct signal to USB.
Can I use it with a Color Control GX?
Yes. Plug the USB end into one of the GX's USB ports and the VE.Direct device shows up on the GX and on the VRM portal. Connect the cable after the GX has fully booted for the cleanest result.
Do I need to install a driver?
On most current computers, installing VictronConnect sets up the USB driver for you, so you plug in and the device appears.
My device connects but shows as unknown on the GX. Why?
That usually means the GX firmware is older than the device. Update the GX firmware and the name typically resolves.
Can I connect more than one VE.Direct device to a GX this way?
Yes, using additional cables and USB ports. If two devices of the same type show up as duplicates, set their instance numbers in the GX menu so each appears separately.
What if 0.9 meters won't reach?
Use a powered USB extension rather than a long passive one. A powered extension holds the data signal better over distance, which matters on bigger boats where the monitor and the GX are compartments apart.
Will it hold up in a boat's engine room?
Keep it away from direct engine heat and, on noisy powerboats, add a ferrite choke near the GX end to keep ignition EMI out of the readings. Routed sensibly, it's a reliable long-term link.