{"product_id":"victron-multiplus-ii-12v-4k-160-50-inverter-charger","title":"Victron MultiPlus-II 12V\/4k 160-50 2x120V Inverter\/Charger","description":"\u003cp class=\"nvn-hero\"\u003eThe Victron MultiPlus-II 12V\/4k 160-50 2x120V combines an inverter, a battery charger, and an AC transfer switch in one unit. It handles split-phase or single-phase shore power, adds PowerAssist for weak docks and small generators, and expands with parallel or three-phase setups.\u003c\/p\u003e\n\n\u003cdiv class=\"nvn-description\"\u003e\n\u003cp\u003eIf you're building a power system on a boat, camper van, or off-grid cabin and you want one box that handles inverting, charging, and shore power switching, the Victron MultiPlus-II 12V\/4k 160-50 2x120V is built for exactly that job. It takes the place of a separate inverter, a separate battery charger, and a separate transfer switch. Fewer boxes means fewer cables, fewer failure points, and a tidier install in the engine room or lazarette.\u003c\/p\u003e\n\u003cp\u003eHere's how it behaves day to day. When shore or generator power is present, the MultiPlus-II passes that AC through to your loads and uses whatever is left over to charge the batteries. The AC input can come from a split-phase 120\/240 V source or a single-phase 120 V source. The unit connects to the neutral and the preferred input line, L1, so charging power is drawn from L1. When the AC goes away, it switches to inverter mode and keeps your 120 V loads running.\u003c\/p\u003e\n\u003cp\u003eThat switchover is quick. The transfer time on the L1 output is less than 18 milliseconds, so computers and other sensitive electronics keep running without a hiccup. The L2 output is slower, at approximately 40 milliseconds. Worth knowing if you're planning which loads go on which line.\u003c\/p\u003e\n\u003cp\u003eInverter mode has one rule you need to understand before you buy. The inverter output is 120 V single-phase, and in inverter mode the unit ties both output lines, L1 and L2, together to feed 120 VAC to loads on either line. So any 240 V loads only get power when the unit is fed from a split-phase AC source. That's actually a feature. It keeps big loads like a 240 V water heater or air conditioner from draining your battery bank when you're running on the inverter.\u003c\/p\u003e\n\u003cp\u003ePowerControl and PowerAssist are the two features that make this unit earn its keep on small docks and weak generators. With PowerControl you set a maximum grid or generator current. The MultiPlus-II accounts for your other AC loads and uses only the surplus for charging, so you don't trip the pedestal breaker or overload the genset. PowerAssist goes a step further. When peak demand spikes, say the microwave and the coffee maker at the same time, the unit makes up the shortfall from the battery. When the load drops, that spare capacity goes back into recharging. PowerAssist is available on the L1 input only.\u003c\/p\u003e\n\u003cp\u003eThere are two AC outputs. The main output has no break functionality, so it takes over supply to your connected 120 V loads the moment shore or generator power is lost. The second, auxiliary output is live only when AC is present at the input. Put things on it that shouldn't ever pull from the battery, like a water heater element or a battery-hungry space heater, and the inverter won't try to run them off your bank.\u003c\/p\u003e\n\u003cp\u003eNeed more power later? You don't have to start over. Up to 6 units can run in parallel to raise total output. Three units of the same model can also be configured for three-phase output. Keep in mind that in multi-phase setups, L2 is disabled on all units.\u003c\/p\u003e\n\u003cp\u003eSetup is done with VEConfigure software on a computer or laptop. You'll need an MK3-USB interface to connect. Settings can be changed in a matter of minutes, so dialing it in for your battery type and shore power limits isn't a weekend project. For monitoring and control you have several options, including a Cerbo GX or Ekrano GX, a Battery Monitor, a Digital Multi Control Panel, or Bluetooth with the optional VE.Bus Smart dongle. Add a Cerbo GX or other GX product with an internet connection and you can view operational data on Victron's VRM (Victron Remote Management) website, free of charge, and change settings remotely.\u003c\/p\u003e\n\u003cp\u003eThis is a 12 V unit, so it's meant for 12 V battery banks. It ships at 55.4 lb in a 28.50 x 14.00 x 11.00 inch box, so plan on two people and a solid mounting surface. We're an authorized Victron Energy reseller, and if you're sizing a system and aren't sure whether this model fits your loads, our crew is happy to talk it through before you order.\u003c\/p\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eKey Features\u003c\/h2\u003e\n\u003cul class=\"nvn-features\"\u003e\n  \u003cli\u003e12V system voltage, so it drops onto a standard 12 V house battery bank.\u003c\/li\u003e\n  \u003cli\u003eInverter, battery charger, and AC transfer switch in one unit, which cuts down on boxes and wiring.\u003c\/li\u003e\n  \u003cli\u003eAccepts split-phase 120\/240 V or single-phase 120 V AC input, so it works with a range of shore and generator setups.\u003c\/li\u003e\n  \u003cli\u003e2x120V AC outputs. The main output backs up your loads and the auxiliary output only runs when AC is present at the input.\u003c\/li\u003e\n  \u003cli\u003eL1 transfer time under 18 milliseconds, so computers and electronics ride through a power loss.\u003c\/li\u003e\n  \u003cli\u003ePowerControl caps the current drawn from the grid or generator so you don't overload a weak source.\u003c\/li\u003e\n  \u003cli\u003ePowerAssist adds battery power on top of a limited shore or generator supply during peak demand (L1 input only).\u003c\/li\u003e\n  \u003cli\u003eUp to 6 units in parallel for more power, or 3 identical units for three-phase output.\u003c\/li\u003e\n  \u003cli\u003eConfigured with VEConfigure software and an MK3-USB interface, with Bluetooth available through the optional VE.Bus Smart dongle.\u003c\/li\u003e\n  \u003cli\u003eFree remote monitoring and settings changes through VRM when paired with a Cerbo GX or other GX device.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"nvn-trust\"\u003e\n  \u003ch2\u003eWhy Buy from NVN Marine\u003c\/h2\u003e\n  \u003cul\u003e\n    \u003cli\u003eAuthorized Victron Energy reseller, full manufacturer warranty\u003c\/li\u003e\n    \u003cli\u003eNMEA member and ABYC certified, advice from real boat techs\u003c\/li\u003e\n    \u003cli\u003eSame-day shipping before 3 PM ET on in-stock items\u003c\/li\u003e\n    \u003cli\u003eNY headquarters and Fort Lauderdale flagship retail store\u003c\/li\u003e\n  \u003c\/ul\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eFrequently Asked Questions\u003c\/h2\u003e\n\u003cdiv class=\"nvn-faq\"\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eIs the Victron MultiPlus-II 12V\/4k 160-50 an inverter and a charger?\u003c\/summary\u003e\n    \u003cp\u003eYes. It's an inverter\/charger. It also passes shore or generator AC through to your loads, so it handles the transfer switching too.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhat AC input does it accept?\u003c\/summary\u003e\n    \u003cp\u003eThe AC input can be supplied from a split-phase 120\/240 V source or a single-phase 120 V source. The unit connects to the neutral and the preferred input line, L1, and battery charging power is drawn from L1.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWill it run 240 V loads off the battery?\u003c\/summary\u003e\n    \u003cp\u003eNo. In inverter mode the output is always 120 V single-phase, with both output lines tied together to supply 120 VAC to loads on either line. 240 V loads only get power when the unit is fed from a split-phase AC source.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eHow fast does it switch to the battery when shore power drops?\u003c\/summary\u003e\n    \u003cp\u003eThe transfer time on the L1 output is less than 18 milliseconds. The L2 output is slower, at approximately 40 milliseconds.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhat's the difference between PowerControl and PowerAssist?\u003c\/summary\u003e\n    \u003cp\u003ePowerControl lets you set a maximum grid or generator current. The unit uses only the surplus after your other loads for charging. PowerAssist adds battery power to make up for insufficient shore or generator power during peaks, then recharges when the load drops. PowerAssist is available on the L1 input only.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhat is the second AC output for?\u003c\/summary\u003e\n    \u003cp\u003eThe auxiliary output is live only when AC is available at the input of the unit. It's the place to connect loads that shouldn't discharge the battery.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eCan I run more than one in parallel?\u003c\/summary\u003e\n    \u003cp\u003eYes. Up to 6 units can run in parallel for higher power output. Three units of the same model can also be set up for three-phase output, and L2 is disabled on all units in multi-phase setups.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eHow do I configure it?\u003c\/summary\u003e\n    \u003cp\u003eUse VEConfigure software on a computer or laptop with an MK3-USB interface. Settings can be changed in a matter of minutes.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhat do I need for monitoring and remote access?\u003c\/summary\u003e\n    \u003cp\u003eLocal options include a Cerbo GX, Ekrano GX, Battery Monitor, Digital Multi Control Panel, or Bluetooth with the optional VE.Bus Smart dongle. For remote access, install a Cerbo GX or other GX product with an internet connection. Data is stored and shown on the VRM website free of charge.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eHow much does it weigh and how big is the box?\u003c\/summary\u003e\n    \u003cp\u003eShipping weight is 55.4 lb and the box measures 28.50 x 14.00 x 11.00 inches.\u003c\/p\u003e\n  \u003c\/details\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eTechnical Specifications\u003c\/h2\u003e\n\u003ctable class=\"nvn-specs\"\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n\u003cth\u003eTitle\u003c\/th\u003e\n\u003ctd\u003eVictron MultiPlus-II 12V\/4k 160-50 2x120V 50\/60Hz Inverter\/Charger\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eBrand\u003c\/th\u003e\n\u003ctd\u003eVictron Energy\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eManufacturer Part Number\u003c\/th\u003e\n\u003ctd\u003ePMP122405210\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eUPC\u003c\/th\u003e\n\u003ctd\u003e8719076079620\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eModel Designation\u003c\/th\u003e\n\u003ctd\u003eMultiPlus-II 12V\/4k 160-50 2x120V\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eSystem Voltage\u003c\/th\u003e\n\u003ctd\u003e12V\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eAC Output\u003c\/th\u003e\n\u003ctd\u003e2x120V\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eFrequency\u003c\/th\u003e\n\u003ctd\u003e50\/60Hz\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eCategory\u003c\/th\u003e\n\u003ctd\u003eElectrical | Charger\/Inverter Combos\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003e55.4 lb\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003ePackage Dimensions (L x W x H)\u003c\/th\u003e\n\u003ctd\u003e28.50 x 14.00 x 11.00 in\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eAC Input\u003c\/th\u003e\n\u003ctd\u003eSplit-phase 120\/240 V or single-phase 120 V\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eInverter Output\u003c\/th\u003e\n\u003ctd\u003e120 V single-phase\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eTransfer Time (L1 Output)\u003c\/th\u003e\n\u003ctd\u003eLess than 18 milliseconds\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eTransfer Time (L2 Output)\u003c\/th\u003e\n\u003ctd\u003eApproximately 40 milliseconds\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eParallel Operation\u003c\/th\u003e\n\u003ctd\u003eUp to 6 units\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eThree-Phase Operation\u003c\/th\u003e\n\u003ctd\u003e3 units of the same model\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eConfiguration Software\u003c\/th\u003e\n\u003ctd\u003eVEConfigure (MK3-USB interface required)\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eRemote Monitoring\u003c\/th\u003e\n\u003ctd\u003eVRM (Victron Remote Management), free of charge\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003cscript type=\"application\/ld+json\"\u003e\n{\n    \"@context\": \"https:\/\/schema.org\",\n    \"@type\": \"FAQPage\",\n    \"mainEntity\": [\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Is the Victron MultiPlus-II 12V\/4k 160-50 an inverter and a charger?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Yes. It's an inverter\/charger. It also passes shore or generator AC through to your loads, so it handles the transfer switching too.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"What AC input does it accept?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"The AC input can be supplied from a split-phase 120\/240 V source or a single-phase 120 V source. The unit connects to the neutral and the preferred input line, L1, and battery charging power is drawn from L1.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Will it run 240 V loads off the battery?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"No. In inverter mode the output is always 120 V single-phase, with both output lines tied together to supply 120 VAC to loads on either line. 240 V loads only get power when the unit is fed from a split-phase AC source.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"How fast does it switch to the battery when shore power drops?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"The transfer time on the L1 output is less than 18 milliseconds. The L2 output is slower, at approximately 40 milliseconds.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"What's the difference between PowerControl and PowerAssist?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"PowerControl lets you set a maximum grid or generator current. The unit uses only the surplus after your other loads for charging. PowerAssist adds battery power to make up for insufficient shore or generator power during peaks, then recharges when the load drops. PowerAssist is available on the L1 input only.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"What is the second AC output for?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"The auxiliary output is live only when AC is available at the input of the unit. It's the place to connect loads that shouldn't discharge the battery.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Can I run more than one in parallel?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Yes. Up to 6 units can run in parallel for higher power output. Three units of the same model can also be set up for three-phase output, and L2 is disabled on all units in multi-phase setups.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"How do I configure it?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Use VEConfigure software on a computer or laptop with an MK3-USB interface. Settings can be changed in a matter of minutes.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"What do I need for monitoring and remote access?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Local options include a Cerbo GX, Ekrano GX, Battery Monitor, Digital Multi Control Panel, or Bluetooth with the optional VE.Bus Smart dongle. For remote access, install a Cerbo GX or other GX product with an internet connection. Data is stored and shown on the VRM website free of charge.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"How much does it weigh and how big is the box?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Shipping weight is 55.4 lb and the box measures 28.50 x 14.00 x 11.00 inches.\"\n            }\n        }\n    ]\n}\n\u003c\/script\u003e\n","brand":"Victron Energy","offers":[{"title":"Default Title","offer_id":68051537231965,"sku":"116127","price":1236.75,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0299\/7266\/0317\/files\/116127XL.jpg?v=1794973699","url":"https:\/\/nvnmarine.com\/products\/victron-multiplus-ii-12v-4k-160-50-inverter-charger","provider":"NVN Marine","version":"1.0","type":"link"}