{"product_id":"taco-marine-polymer-sheet-24x54-1-2in-arctic-white","title":"TACO Metals Marine Polymer Sheet 24 x 54 x 1\/2 In Arctic White","description":"\u003cp class=\"nvn-hero\"\u003eThe TACO Metals marine polymer sheet is a 24 by 54 inch panel of Arctic White polyethylene, a half inch thick. It's marine lumber that won't rot, soak up water, or need paint. Cut it, drill it, bolt it down, and build the custom part your boat's been missing.\u003c\/p\u003e\n\n\u003cdiv class=\"nvn-description\"\u003e\n\u003cp\u003eThe TACO Metals marine polymer sheet is one of those materials that earns a permanent spot in your shop. It's a solid 24 by 54 inch panel of marine-grade polyethylene, a half inch thick, in Arctic White. Unlike plywood or dimensional lumber, it won't rot, it won't soak up water, and it never needs paint or sealant. Cut it, drill it, bolt it down, and forget about it.\u003c\/p\u003e\n\u003cp\u003eBoaters reach for a sheet like this when they want to build something custom that has to live outdoors. We've seen it turned into electronics mounting plates behind the console, backing boards for cleats and rod holders, hatch and locker lids, step pads, trim panels, and fillet or bait boards for the transom. On a 20 to 25 foot center console, this 24 by 54 panel is a nice size for a small bait station or a cutting surface. On bigger boats it does duty as helm and dash panels, tackle-center dividers, and battery or pump mounting plates down in the bilge where wood would never survive. If you've ever had a wooden mounting board swell, delaminate, and rust out the hardware behind it, you already know why folks switch to polymer.\u003c\/p\u003e\n\u003cp\u003eWorking with it is straightforward if you treat it like a soft plastic and not like wood. Standard woodworking tools cut it clean. Use sharp blades and, for holes, sharp brad-point bits with a backing board underneath so you don't get melt or blowout on the exit side. Feed it steady so the material shears instead of gumming up. One thing to know up front: glue doesn't reliably bond to marine polyethylene. Plan on mechanical fasteners, screws, bolts, or through-bolts with backing washers, for anything that has to hold.\u003c\/p\u003e\n\u003cp\u003eHalf-inch stock is a good middle ground. It's stiff enough for panels, brackets, and most backing jobs, but on a wide unsupported span it will flex under load. If you're building a work surface or a table top out of it, frame the edges or back it with a stiffener so it stays flat. And because polymer moves with temperature more than wood does, leave yourself about an eighth of an inch of gap around a panel that sits in direct sun. That little bit of room keeps it from bowing when it heats up.\u003c\/p\u003e\n\u003cp\u003eThe Arctic White finish looks clean and bright against gelcoat and blends into just about any boat. It wipes down with soap and water, and there's no grain to seal or edge to varnish. Fair warning on high-traffic work surfaces: white shows knife scuffs and scratches over time. That's cosmetic, not structural, and it's the tradeoff for the bright look. If you want to hide wear on a heavily used cutting board, a darker sheet hides it better, but for panels, trim, and backing the white is hard to beat.\u003c\/p\u003e\n\u003cp\u003eWhat sells most boaters on polymer over wood is the total lack of upkeep. There's nothing to sand, nothing to re-varnish every season, and no soft spots to chase down two summers from now. Both faces of the sheet are usable, so you're not fussing over a good side and a bad side when you lay out your cut. Store the offcuts flat, and they'll be ready for the next project whenever you need a bracket or a spacer.\u003c\/p\u003e\n\u003cp\u003eThis is a material for the DIY rigger and the weekend fabricator who'd rather build it once and never think about it again. It's UV-stabilized for life on the water, it holds fasteners well, and it shrugs off salt, spray, and sun. Order a sheet, rough out your part, and you've got marine hardware that'll outlast the project you built it for.\u003c\/p\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eKey Features\u003c\/h2\u003e\n\u003cul class=\"nvn-features\"\u003e\n  \u003cli\u003eHalf-inch (1\/2 in) marine-grade polyethylene sheet, 24 in by 54 in, for custom on-boat fabrication\u003c\/li\u003e\n  \u003cli\u003eWon't rot, delaminate, or absorb water, so it survives where plywood fails\u003c\/li\u003e\n  \u003cli\u003eNever needs paint, varnish, or sealant, cutting seasonal upkeep to zero\u003c\/li\u003e\n  \u003cli\u003eArctic White finish stays bright against gelcoat and wipes clean with soap and water\u003c\/li\u003e\n  \u003cli\u003eCuts and machines with standard woodworking tools for DIY brackets, panels, and backing boards\u003c\/li\u003e\n  \u003cli\u003eBoth faces usable, no finished side to work around when laying out a cut\u003c\/li\u003e\n  \u003cli\u003eUV-stabilized to shrug off salt, spray, and constant sun exposure\u003c\/li\u003e\n  \u003cli\u003eHolds mechanical fasteners well for cleats, rod holders, electronics plates, and hatch lids\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"nvn-trust\"\u003e\n  \u003ch2\u003eWhy Buy from NVN Marine\u003c\/h2\u003e\n  \u003cul\u003e\n    \u003cli\u003eAuthorized TACO METALS reseller, full manufacturer warranty\u003c\/li\u003e\n    \u003cli\u003eNMEA member and ABYC certified, advice from real boat techs\u003c\/li\u003e\n    \u003cli\u003eSame-day shipping before 3 PM ET on in-stock items\u003c\/li\u003e\n    \u003cli\u003eNY headquarters and Fort Lauderdale flagship retail store\u003c\/li\u003e\n  \u003c\/ul\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eFrequently Asked Questions\u003c\/h2\u003e\n\u003cdiv class=\"nvn-faq\"\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhat can I build with this marine polymer sheet?\u003c\/summary\u003e\n    \u003cp\u003ePlenty. Boaters use half-inch polymer sheet for electronics mounting plates, backing boards behind cleats and rod holders, hatch and locker lids, step pads, trim panels, and bait or fillet boards. The 24 by 54 size is handy for a small bait station on a center console.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWill it rot or soak up water?\u003c\/summary\u003e\n    \u003cp\u003eNo. Marine polyethylene doesn't absorb water and won't rot, swell, or delaminate the way wood does. That's the main reason folks switch to it for anything mounted outdoors or down in the bilge.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eCan I cut and drill it with regular tools?\u003c\/summary\u003e\n    \u003cp\u003eYes. Standard woodworking tools cut it clean. Use sharp blades, and for holes use sharp brad-point bits with a backing board underneath so you don't get melt or blowout on the exit side. Feed it steady so it shears instead of gumming up.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eCan I glue two pieces together?\u003c\/summary\u003e\n    \u003cp\u003eNot reliably. Glue doesn't bond well to marine polyethylene, so plan on mechanical fasteners: screws, bolts, or through-bolts with backing washers for anything that has to hold load.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eDoes the half-inch sheet flex?\u003c\/summary\u003e\n    \u003cp\u003eOn a wide unsupported span it will flex under load. For a work surface or table top, frame the edges or back it with a stiffener so it stays flat. For panels, brackets, and backing jobs it's plenty stiff on its own.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eDoes it need paint or sealing?\u003c\/summary\u003e\n    \u003cp\u003eNo. There's no grain to seal and no edge to varnish. The color goes all the way through, so a scratch doesn't expose raw material.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWill the Arctic White scuff?\u003c\/summary\u003e\n    \u003cp\u003eOn a heavily used cutting or work surface, white shows knife scuffs and scratches over time. That's cosmetic, not structural. For panels, trim, and backing it stays looking clean.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eDoes it expand in the sun?\u003c\/summary\u003e\n    \u003cp\u003ePolymer moves with temperature more than wood, so a panel in direct sun expands and contracts. Leave roughly an eighth of an inch of gap around it when you mount it so it doesn't bow as it heats.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eHow do I clean it?\u003c\/summary\u003e\n    \u003cp\u003eSoap and water. It wipes right down and there's no finish to strip or reseal.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eIs it UV stable for outdoor marine use?\u003c\/summary\u003e\n    \u003cp\u003eYes. The sheet is UV-stabilized to hold up to constant sun, salt, and spray, which is what makes it a true marine material rather than a general-purpose plastic.\u003c\/p\u003e\n  \u003c\/details\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eTechnical Specifications\u003c\/h2\u003e\n\u003ctable class=\"nvn-specs\"\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n\u003cth\u003eTitle\u003c\/th\u003e\n\u003ctd\u003eTACO Metals Marine Polymer Sheet 24 x 54 x 1\/2 In Arctic White\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eBrand\u003c\/th\u003e\n\u003ctd\u003eTACO METALS\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eManufacturer Part Number\u003c\/th\u003e\n\u003ctd\u003eP10-5024WHA54-1\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eUPC\u003c\/th\u003e\n\u003ctd\u003e630838009014\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eMarine-grade Polyethylene\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eColor\u003c\/th\u003e\n\u003ctd\u003eArctic White\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e24 inches\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eWidth\u003c\/th\u003e\n\u003ctd\u003e54 inches\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eThickness\u003c\/th\u003e\n\u003ctd\u003e1\/2 inch\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eProduct Type\u003c\/th\u003e\n\u003ctd\u003eMarine Lumber Sheet\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eFastening Method\u003c\/th\u003e\n\u003ctd\u003eMechanical fasteners (no reliable adhesive bond)\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eUV Protection\u003c\/th\u003e\n\u003ctd\u003eUV-stabilized for marine use\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003cscript type=\"application\/ld+json\"\u003e\n{\n    \"@context\": \"https:\/\/schema.org\",\n    \"@type\": \"FAQPage\",\n    \"mainEntity\": [\n        {\n            \"@type\": \"Question\",\n            \"name\": \"What can I build with this marine polymer sheet?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Plenty. Boaters use half-inch polymer sheet for electronics mounting plates, backing boards behind cleats and rod holders, hatch and locker lids, step pads, trim panels, and bait or fillet boards. The 24 by 54 size is handy for a small bait station on a center console.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Will it rot or soak up water?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"No. Marine polyethylene doesn't absorb water and won't rot, swell, or delaminate the way wood does. That's the main reason folks switch to it for anything mounted outdoors or down in the bilge.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Can I cut and drill it with regular tools?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Yes. Standard woodworking tools cut it clean. Use sharp blades, and for holes use sharp brad-point bits with a backing board underneath so you don't get melt or blowout on the exit side. Feed it steady so it shears instead of gumming up.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Can I glue two pieces together?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Not reliably. Glue doesn't bond well to marine polyethylene, so plan on mechanical fasteners: screws, bolts, or through-bolts with backing washers for anything that has to hold load.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Does the half-inch sheet flex?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"On a wide unsupported span it will flex under load. For a work surface or table top, frame the edges or back it with a stiffener so it stays flat. For panels, brackets, and backing jobs it's plenty stiff on its own.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Does it need paint or sealing?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"No. There's no grain to seal and no edge to varnish. The color goes all the way through, so a scratch doesn't expose raw material.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Will the Arctic White scuff?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"On a heavily used cutting or work surface, white shows knife scuffs and scratches over time. That's cosmetic, not structural. For panels, trim, and backing it stays looking clean.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Does it expand in the sun?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Polymer moves with temperature more than wood, so a panel in direct sun expands and contracts. Leave roughly an eighth of an inch of gap around it when you mount it so it doesn't bow as it heats.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"How do I clean it?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Soap and water. It wipes right down and there's no finish to strip or reseal.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Is it UV stable for outdoor marine use?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Yes. The sheet is UV-stabilized to hold up to constant sun, salt, and spray, which is what makes it a true marine material rather than a general-purpose plastic.\"\n            }\n        }\n    ]\n}\n\u003c\/script\u003e\n","brand":"TACO METALS","offers":[{"title":"Default Title","offer_id":45000676311133,"sku":"2008021","price":217.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0299\/7266\/0317\/files\/ImageServerAPI_6d211dbf-e092-4ff2-a3f6-02f48c5708bb.jpg?v=1788749384","url":"https:\/\/nvnmarine.com\/products\/taco-marine-polymer-sheet-24x54-1-2in-arctic-white","provider":"NVN Marine","version":"1.0","type":"link"}