{"product_id":"taco-marine-poly-sheet-24x54-1-4in-arctic-white","title":"TACO Marine Arctic White Poly Sheet, 24 x 54 x 1\/4 Inch","description":"\u003cp class=\"nvn-hero\"\u003eTACO Marine polyethylene marine lumber in a 24 by 54 inch sheet, a quarter inch thick, in Arctic White. It's blank stock for custom faceplates, mounting boards, backing plates, and trim. Won't rot, won't swell, and never needs paint or sealer.\u003c\/p\u003e\n\n\u003cdiv class=\"nvn-description\"\u003e\n\u003cp\u003eThis is TACO Marine polyethylene marine lumber, cut to a 24 by 54 inch sheet at a quarter inch thick in Arctic White. Think of it as blank stock. You bring the project, this gives you the material. Boaters reach for poly sheet like this when they need a clean, weatherproof panel that won't rot, won't swell, and never needs paint. It's one of those things that's handy to have on the shelf before you need it.\u003c\/p\u003e\n\u003cp\u003eThe most common job we see it used for is custom electronics faceplates on center consoles. You've added a new gauge, a switch panel, or a small display, and the factory dash doesn't have a spot for it. Cut a piece of this, lay out your holes, and you've got a finished-looking mounting surface that fits the boat. It's just as at home as a mounting board for pumps and electrical gear, a backing plate behind cleats or deck hardware, trim around a hatch, or a small custom cover.\u003c\/p\u003e\n\u003cp\u003ePolyethylene is the reason this material has been a boat-shop staple for years. It doesn't absorb water. It won't rot the way wood does, and it doesn't need sealing, painting, or fiberglassing to survive out there. Salt, spray, washdowns, none of it bothers the material. When it gets dirty, soap and water and a rag brings it right back. That's a big part of why folks build console and cabin parts out of poly instead of plywood.\u003c\/p\u003e\n\u003cp\u003eA quarter inch is a versatile thickness. It's stiff enough for faceplates, backing plates, and small panels, and thin enough to trim into odd shapes without a fight. One thing worth knowing up front. At a quarter inch, a wide unsupported span will flex under load. So if you're building something like a hatch cover on a walkaround, frame the edges or add a backing rib to stiffen it. For faceplates and mounting boards that sit against a solid surface, the quarter inch is plenty.\u003c\/p\u003e\n\u003cp\u003eFabrication is straightforward if you respect the material. Polyethylene machines beautifully, but it likes a sharp carbide blade and a lower speed. Run it too fast and the friction melts the plastic and gums up the cut. On thin stock like this, a lot of guys score-and-snap for straight cuts and save the saw for curves. It drills and countersinks clean, so you can set fasteners flush. And it routs to a smooth edge when you want a finished look.\u003c\/p\u003e\n\u003cp\u003eTwo field tips that save headaches. First, don't leave a loose sheet lying in direct sun before you fasten it down. Thin poly can warp in the heat. Pre-fit your piece, then clamp it overnight or fasten it promptly so it sets flat. Second, for a permanent bond, back up your mechanical fasteners with a marine polyurethane adhesive sealant. Poly is slick, so a good sealant plus screws holds far better than adhesive alone.\u003c\/p\u003e\n\u003cp\u003eOn the color, Arctic White is bright and clean, and it blends with the white gelcoat and trim on most boats. Fair warning, white does show scuffs and scrapes sooner than a darker shade, so in a high-traffic foot area you'll notice wear faster. For faceplates, mounting boards, and trim up off the deck, that's rarely an issue and the clean white look is exactly what most people want.\u003c\/p\u003e\n\u003cp\u003eOne sheet gives you nine square feet to work with, enough for several small faceplates or one larger panel, and you can save the offcuts for the next little job. If you fabricate your own boat parts, this is the kind of material you'll keep reaching for. It stores flat, it doesn't go bad sitting in the shop, and when a project comes up you've already got the stock on hand instead of waiting on an order.\u003c\/p\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eKey Features\u003c\/h2\u003e\n\u003cul class=\"nvn-features\"\u003e\n  \u003cli\u003ePolyethylene construction won't rot, swell, or absorb water, so you can skip paint and sealer\u003c\/li\u003e\n  \u003cli\u003e1\/4 inch thickness cuts, drills, and routs clean with standard shop tools\u003c\/li\u003e\n  \u003cli\u003e24 by 54 inch sheet gives you 9 square feet of blank stock for multiple faceplates or one large panel\u003c\/li\u003e\n  \u003cli\u003eArctic White finish stays bright and blends with white gelcoat and cabin trim\u003c\/li\u003e\n  \u003cli\u003eNon-porous surface wipes clean with soap and water, no special care\u003c\/li\u003e\n  \u003cli\u003eMachines with a carbide blade for smooth edges on faceplates and mounting boards\u003c\/li\u003e\n  \u003cli\u003eThin enough to trim into odd shapes, stiff enough for backing plates and small panels\u003c\/li\u003e\n  \u003cli\u003eMarine-grade polyethylene stands up to salt, spray, and washdowns\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"nvn-trust\"\u003e\n  \u003ch2\u003eWhy Buy from NVN Marine\u003c\/h2\u003e\n  \u003cul\u003e\n    \u003cli\u003eAuthorized TACO Marine reseller, full manufacturer warranty\u003c\/li\u003e\n    \u003cli\u003eNMEA member and ABYC certified, advice from real boat techs\u003c\/li\u003e\n    \u003cli\u003eSame-day shipping before 3 PM ET on in-stock items\u003c\/li\u003e\n    \u003cli\u003eNY headquarters and Fort Lauderdale flagship retail store\u003c\/li\u003e\n  \u003c\/ul\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eFrequently Asked Questions\u003c\/h2\u003e\n\u003cdiv class=\"nvn-faq\"\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhat is this sheet made of?\u003c\/summary\u003e\n    \u003cp\u003eIt's TACO Marine polyethylene marine lumber. Polyethylene is a weatherproof plastic that doesn't rot, swell, or absorb water, which is why it's used for boat parts instead of wood.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhat can I use it for?\u003c\/summary\u003e\n    \u003cp\u003eCustom electronics faceplates, mounting boards for pumps and electrical gear, backing plates behind cleats and hardware, hatch trim, and small custom covers. It's blank stock you cut to fit your project.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eHow do I cut it cleanly?\u003c\/summary\u003e\n    \u003cp\u003eUse a sharp carbide blade at a lower speed. Run it too fast and the friction melts the plastic and binds the cut. On thin stock like this, a score-and-snap works well for straight cuts and the saw handles the curves.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eDoes it need paint or sealing?\u003c\/summary\u003e\n    \u003cp\u003eNo. Polyethylene doesn't rot or absorb water, so there's no sealing, painting, or fiberglassing needed. That's the main advantage over plywood.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWill a quarter inch hold up as a hatch cover?\u003c\/summary\u003e\n    \u003cp\u003eAt a quarter inch, a wide unsupported span will flex under load. For a hatch cover or a longer span, frame the edges or add a backing rib to stiffen it. For faceplates and mounting boards against a solid surface, the quarter inch is plenty.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eHow do I keep it from warping before I install it?\u003c\/summary\u003e\n    \u003cp\u003eDon't leave a loose sheet sitting in direct sun. Thin poly can warp in the heat. Pre-fit your piece, then clamp it or fasten it promptly so it sets flat.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhat's the best way to bond it permanently?\u003c\/summary\u003e\n    \u003cp\u003ePolyethylene is slick, so back up your mechanical fasteners with a marine polyurethane adhesive sealant. Screws plus sealant hold far better than adhesive on its own.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eHow much area does one sheet cover?\u003c\/summary\u003e\n    \u003cp\u003eThe sheet is 24 by 54 inches, which works out to 9 square feet. That's enough for several small faceplates or one larger panel.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eCan I drill and countersink it?\u003c\/summary\u003e\n    \u003cp\u003eYes. It drills easily and countersinks clean, so you can set fasteners flush for a finished look.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWill the white show scuffs?\u003c\/summary\u003e\n    \u003cp\u003eArctic White shows scuffs and scrapes sooner than a darker color, so it's better suited to faceplates, trim, and mounting boards up off the deck than to high-traffic foot areas.\u003c\/p\u003e\n  \u003c\/details\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eTechnical Specifications\u003c\/h2\u003e\n\u003ctable class=\"nvn-specs\"\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n\u003cth\u003eTitle\u003c\/th\u003e\n\u003ctd\u003e24 Inch Length x 54 Inch Width; 1\/4 Inch Thickness; Arctic White; Polyethylene\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eBrand\u003c\/th\u003e\n\u003ctd\u003eTACO Marine\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eManufacturer\u003c\/th\u003e\n\u003ctd\u003eTACO Metals\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eManufacturer Part Number\u003c\/th\u003e\n\u003ctd\u003eP10-2524WHA54-1\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eUPC\u003c\/th\u003e\n\u003ctd\u003e630838012212\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003ePolyethylene\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eColor\u003c\/th\u003e\n\u003ctd\u003eArctic White\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eSheet Length\u003c\/th\u003e\n\u003ctd\u003e24 in\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eSheet Width\u003c\/th\u003e\n\u003ctd\u003e54 in\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eSheet Thickness\u003c\/th\u003e\n\u003ctd\u003e1\/4 in\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eCoverage Area\u003c\/th\u003e\n\u003ctd\u003e9 sq ft (24 in x 54 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eProduct Type\u003c\/th\u003e\n\u003ctd\u003eMarine Lumber Sheet\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003cscript type=\"application\/ld+json\"\u003e\n{\n    \"@context\": \"https:\/\/schema.org\",\n    \"@type\": \"FAQPage\",\n    \"mainEntity\": [\n        {\n            \"@type\": \"Question\",\n            \"name\": \"What is this sheet made of?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"It's TACO Marine polyethylene marine lumber. Polyethylene is a weatherproof plastic that doesn't rot, swell, or absorb water, which is why it's used for boat parts instead of wood.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"What can I use it for?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Custom electronics faceplates, mounting boards for pumps and electrical gear, backing plates behind cleats and hardware, hatch trim, and small custom covers. It's blank stock you cut to fit your project.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"How do I cut it cleanly?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Use a sharp carbide blade at a lower speed. Run it too fast and the friction melts the plastic and binds the cut. On thin stock like this, a score-and-snap works well for straight cuts and the saw handles the curves.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Does it need paint or sealing?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"No. Polyethylene doesn't rot or absorb water, so there's no sealing, painting, or fiberglassing needed. That's the main advantage over plywood.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Will a quarter inch hold up as a hatch cover?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"At a quarter inch, a wide unsupported span will flex under load. For a hatch cover or a longer span, frame the edges or add a backing rib to stiffen it. For faceplates and mounting boards against a solid surface, the quarter inch is plenty.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"How do I keep it from warping before I install it?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Don't leave a loose sheet sitting in direct sun. Thin poly can warp in the heat. Pre-fit your piece, then clamp it or fasten it promptly so it sets flat.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"What's the best way to bond it permanently?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Polyethylene is slick, so back up your mechanical fasteners with a marine polyurethane adhesive sealant. Screws plus sealant hold far better than adhesive on its own.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"How much area does one sheet cover?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"The sheet is 24 by 54 inches, which works out to 9 square feet. That's enough for several small faceplates or one larger panel.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Can I drill and countersink it?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Yes. It drills easily and countersinks clean, so you can set fasteners flush for a finished look.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Will the white show scuffs?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Arctic White shows scuffs and scrapes sooner than a darker color, so it's better suited to faceplates, trim, and mounting boards up off the deck than to high-traffic foot areas.\"\n            }\n        }\n    ]\n}\n\u003c\/script\u003e\n","brand":"TACO Marine","offers":[{"title":"Default Title","offer_id":45059707240541,"sku":"2008469","price":114.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0299\/7266\/0317\/files\/ImageServerAPI_8519db6a-72a7-4a0f-a025-79e8aa95a292.jpg?v=1789520188","url":"https:\/\/nvnmarine.com\/products\/taco-marine-poly-sheet-24x54-1-4in-arctic-white","provider":"NVN Marine","version":"1.0","type":"link"}