{"product_id":"t-h-marine-rigging-flange-kit-chrome-2-in-hose","title":"T-H Marine Rigging Flange Kit, Chrome, 2 in Hose","description":"\u003cp class=\"nvn-hero\"\u003eThe T-H Marine Rigging Flange Kit is the clean way to route a bundle of cables and hoses through your deck or splashwell. You get a chrome flange, a corrosion-proof polypropylene body, and 4 feet of 2-inch black rigging hose to carry steering, controls, and wiring down to the bilge. Install it once and forget it's there.\u003c\/p\u003e\n\n\u003cdiv class=\"nvn-description\"\u003e\n\u003cp\u003eEvery rigged boat has that one spot where a bundle of cables and hoses has to disappear through the deck or splashwell and come out clean on the other side. The T-H Marine Rigging Flange Kit is how you make that pass-through look like the builder did it at the factory. You get a chrome-finished flange, a polypropylene body built to shrug off spray, and a 4-foot length of 2-inch black rigging hose to carry your steering cable, control cables, and wiring down into the bilge.\u003c\/p\u003e\n\u003cp\u003eThis is bread-and-butter rigging gear. Anytime you're routing lines out of a transom well, through a console base, or down from a leaning post, you want them channeled and sealed, not flopping around a raw hole in the deck. We reach for a kit like this on repowers all the time. New outboard, new steering, new controls, and suddenly there's a fat bundle that needs a tidy home. The 2-inch hose swallows a surprising amount of gear. A hydraulic steering hose, a couple of control cables, and a wiring harness all fit with room to spare.\u003c\/p\u003e\n\u003cp\u003eThe body is polypropylene, so it won't corrode the way a metal fitting can when it's sitting in a damp bilge or a splashwell that never really dries out. The chrome cap handles the visible side and gives you a finished look right where people see it. It's a light part that carries no real load. Its whole job is to guide and protect the lines running through it, and to seal the hole they pass through.\u003c\/p\u003e\n\u003cp\u003eInstall is straightforward if you take your time. Cut your deck opening to match the flange, and here's the one gotcha worth repeating. On curved or crowned surfaces, measure twice so the flange seats flush and the cap sits right. Feed your cables and hoses through the 4-foot black hose first, then run the hose through the flange and down to wherever your bundle terminates. Bed the flange in a good marine sealant so nothing weeps around the collar. And at the hose barb, double-clamp it. On a planing hull that pounds all day, a single clamp can back off and let water track down the hose. Two clamps and you'll forget it's even there.\u003c\/p\u003e\n\u003cp\u003eThe included hose is 4 feet of 2-inch black flexible rigging hose. That's enough for most transom-to-bilge runs on a bay boat or center console. If you're rigging a taller helm and need more reach, you can extend the run with matching 2-inch inside-diameter hose. Want extra chafe protection on the wiring? Slip a length of 2-inch split loom inside the hose, especially where the bundle passes over a deck edge or a sharp fiberglass lip.\u003c\/p\u003e\n\u003cp\u003eOne more note on the hose. The 2-inch size is cut to fit standard 2-inch rigging hose, so any fittings or accessories you already run in that size will play nice with it. Keep your bends gentle. Rigging hose kinks if you crank it into too tight a radius, and a kink can pinch a control cable or restrict a hydraulic line. Give the run a smooth, sweeping path and it'll route cleanly for years.\u003c\/p\u003e\n\u003cp\u003eA couple of things to keep in mind before you order. It's a single kit, so if your cockpit has cables entering the deck in two separate spots, plan on grabbing a second one. And if the pass-through lives entirely below deck where nobody's looking, you may not care about the chrome dress at all, but the sealing and the organization are still worth having. Cables that are channeled and clamped don't chafe, don't rattle, and don't wick water into your bilge.\u003c\/p\u003e\n\u003cp\u003eBottom line, it's a simple part that does an outsized job. It keeps your rigging dry, organized, and looking sharp, and it's the kind of thing you install once and never think about again. If you're not sure the 2-inch size fits your bundle, measure the combined diameter of everything you plan to run and give us a shout. We rig boats for a living, and we're glad to talk it through before you cut a hole in your deck.\u003c\/p\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eKey Features\u003c\/h2\u003e\n\u003cul class=\"nvn-features\"\u003e\n  \u003cli\u003eChrome-finished flange gives a clean, factory look at the deck or splashwell where the rigging passes through\u003c\/li\u003e\n  \u003cli\u003ePolypropylene body won't corrode in a damp bilge or a splashwell that stays wet\u003c\/li\u003e\n  \u003cli\u003eFits standard 2-inch rigging hose, with room for a steering hose, control cables, and a wiring harness together\u003c\/li\u003e\n  \u003cli\u003eIncludes 4 feet of 2-inch black flexible rigging hose to channel and protect the run\u003c\/li\u003e\n  \u003cli\u003eSeals the deck pass-through when bedded in marine sealant, keeping water out of the bilge\u003c\/li\u003e\n  \u003cli\u003eDouble-clamp the hose barb for a connection that holds on a hard-pounding planing hull\u003c\/li\u003e\n  \u003cli\u003eExtend easily with matching 2-inch inside-diameter hose for taller helm runs\u003c\/li\u003e\n  \u003cli\u003eSold as a single complete kit, flange plus hose, ready to install\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"nvn-trust\"\u003e\n  \u003ch2\u003eWhy Buy from NVN Marine\u003c\/h2\u003e\n  \u003cul\u003e\n    \u003cli\u003eAuthorized T-H Marine Supplies reseller, full manufacturer warranty\u003c\/li\u003e\n    \u003cli\u003eNMEA member and ABYC certified, advice from real boat techs\u003c\/li\u003e\n    \u003cli\u003eSame-day shipping before 3 PM ET on in-stock items\u003c\/li\u003e\n    \u003cli\u003eNY headquarters and Fort Lauderdale flagship retail store\u003c\/li\u003e\n  \u003c\/ul\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eFrequently Asked Questions\u003c\/h2\u003e\n\u003cdiv class=\"nvn-faq\"\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhat does this rigging flange kit do?\u003c\/summary\u003e\n    \u003cp\u003eIt gives you a clean, sealed pass-through for cables and hoses where they cross the deck or splashwell. The chrome flange caps the hole for a finished look, and the included 4-foot hose channels your steering, control cables, and wiring down into the bilge.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhat size hose does it fit?\u003c\/summary\u003e\n    \u003cp\u003eIt's built for standard 2-inch rigging hose, and the included hose is that same 2-inch size. Any 2-inch fittings or accessories you already run will match up.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eHow long is the included hose?\u003c\/summary\u003e\n    \u003cp\u003eYou get 4 feet of 2-inch black flexible rigging hose in the kit. That's enough for most transom-to-bilge runs on a bay boat or center console.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhat's the flange made of?\u003c\/summary\u003e\n    \u003cp\u003eThe body is polypropylene, so it won't corrode in a wet bilge or splashwell, and the visible cap has a chrome finish for a clean look at the deck.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhat can I run through the 2-inch hose?\u003c\/summary\u003e\n    \u003cp\u003ePlenty. A hydraulic steering hose, a couple of control cables, and a wiring harness all fit through the 2-inch size together with room to spare.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eHow big do I cut the deck opening?\u003c\/summary\u003e\n    \u003cp\u003eCut the opening to match the flange so it seats flush. On curved or crowned surfaces, measure twice and go slow so the cap sits right against the deck.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eDo I need to seal it?\u003c\/summary\u003e\n    \u003cp\u003eYes. Bed the flange in a quality marine sealant when you install it so water can't weep around the collar and down into the bilge.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eShould I clamp the hose?\u003c\/summary\u003e\n    \u003cp\u003eDouble-clamp the hose at the barb. On a planing hull that pounds, a single clamp can back off over time and let water track down the hose, so two clamps is the safe call.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eCan I extend the hose if 4 feet isn't enough?\u003c\/summary\u003e\n    \u003cp\u003eYes. For a taller helm or a longer run, extend it with matching 2-inch inside-diameter rigging hose. Keep the bends gentle so nothing kinks.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eIs one kit enough for my boat?\u003c\/summary\u003e\n    \u003cp\u003eThis is a single kit. If your cockpit has cables entering the deck in two separate spots, plan on a second one so each run gets its own sealed pass-through.\u003c\/p\u003e\n  \u003c\/details\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eTechnical Specifications\u003c\/h2\u003e\n\u003ctable class=\"nvn-specs\"\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n\u003cth\u003eTitle\u003c\/th\u003e\n\u003ctd\u003eT-H Marine Chrome Rigging Flange Kit with 4 ft of 2-Inch Hose\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eBrand\u003c\/th\u003e\n\u003ctd\u003eT-H Marine Supplies\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eManufacturer Part Number\u003c\/th\u003e\n\u003ctd\u003eRFK-1CP-DP\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eUPC\u003c\/th\u003e\n\u003ctd\u003e733572038408\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eFlange Finish\u003c\/th\u003e\n\u003ctd\u003eChrome\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eBody Material\u003c\/th\u003e\n\u003ctd\u003ePolypropylene\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eCompatible Hose Size\u003c\/th\u003e\n\u003ctd\u003e2 inch\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eIncluded Hose Length\u003c\/th\u003e\n\u003ctd\u003e4 feet\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eIncluded Hose Color\u003c\/th\u003e\n\u003ctd\u003eBlack\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eSold As\u003c\/th\u003e\n\u003ctd\u003eSingle kit\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eProduct Type\u003c\/th\u003e\n\u003ctd\u003eRigging Flange Kit\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eApplication\u003c\/th\u003e\n\u003ctd\u003eDeck and splashwell cable and hose pass-through\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eMounting Style\u003c\/th\u003e\n\u003ctd\u003eSurface-mount flange\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003cscript type=\"application\/ld+json\"\u003e\n{\n    \"@context\": \"https:\/\/schema.org\",\n    \"@type\": \"FAQPage\",\n    \"mainEntity\": [\n        {\n            \"@type\": \"Question\",\n            \"name\": \"What does this rigging flange kit do?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"It gives you a clean, sealed pass-through for cables and hoses where they cross the deck or splashwell. The chrome flange caps the hole for a finished look, and the included 4-foot hose channels your steering, control cables, and wiring down into the bilge.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"What size hose does it fit?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"It's built for standard 2-inch rigging hose, and the included hose is that same 2-inch size. Any 2-inch fittings or accessories you already run will match up.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"How long is the included hose?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"You get 4 feet of 2-inch black flexible rigging hose in the kit. That's enough for most transom-to-bilge runs on a bay boat or center console.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"What's the flange made of?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"The body is polypropylene, so it won't corrode in a wet bilge or splashwell, and the visible cap has a chrome finish for a clean look at the deck.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"What can I run through the 2-inch hose?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Plenty. A hydraulic steering hose, a couple of control cables, and a wiring harness all fit through the 2-inch size together with room to spare.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"How big do I cut the deck opening?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Cut the opening to match the flange so it seats flush. On curved or crowned surfaces, measure twice and go slow so the cap sits right against the deck.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Do I need to seal it?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Yes. Bed the flange in a quality marine sealant when you install it so water can't weep around the collar and down into the bilge.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Should I clamp the hose?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Double-clamp the hose at the barb. On a planing hull that pounds, a single clamp can back off over time and let water track down the hose, so two clamps is the safe call.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Can I extend the hose if 4 feet isn't enough?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Yes. For a taller helm or a longer run, extend it with matching 2-inch inside-diameter rigging hose. Keep the bends gentle so nothing kinks.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Is one kit enough for my boat?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"This is a single kit. If your cockpit has cables entering the deck in two separate spots, plan on a second one so each run gets its own sealed pass-through.\"\n            }\n        }\n    ]\n}\n\u003c\/script\u003e\n","brand":"T-H Marine Supplies","offers":[{"title":"Default Title","offer_id":45072338944093,"sku":"2009223","price":58.79,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0299\/7266\/0317\/files\/ImageServerAPI_29a852c9-516e-4604-8adc-44cf0c06dcb0.jpg?v=1789739364","url":"https:\/\/nvnmarine.com\/products\/t-h-marine-rigging-flange-kit-chrome-2-in-hose","provider":"NVN Marine","version":"1.0","type":"link"}