{"product_id":"t-h-marine-90-degree-flush-mount-rod-holder-white","title":"T-H Marine 90 Degree Flush Mount Rod Holder | White","description":"\u003cp class=\"nvn-hero\"\u003eT-H Marine's 90 degree flat-top rod holder is the simplest way to add a home for a rod. It drops into a 2 inch hole and holds a single rod dead vertical, so the topside stays clean. White finish, 9-1\/2 inches overall, flush trim cap with nothing to snag.\u003c\/p\u003e\n\n\u003cdiv class=\"nvn-description\"\u003e\n\u003cp\u003eIf you keep running out of places to stand your rods, a flush-mount holder is the simplest fix there is. This is T-H Marine's 90 degree flat-top model in white. It drops into a 2 inch hole in your gunwale, deck, or console, and it holds a single rod straight up and out of the way. The whole unit measures 9-1\/2 inches overall, so most of that length sits below the deck where you never see it, keeping the topside clean and open.\u003c\/p\u003e\n\u003cp\u003eThe flat top is the part that matters here. Instead of a raised collar or a gimbal cap, the trim finishes flush with the surface it's mounted in. That means there's nothing to snag a line on and nothing to stub a toe on when you're moving around the cockpit in a hurry. And because the tube holds the rod at 90 degrees, your rod stands dead vertical. That's exactly what you want for storage and for running down the lake, where a rod leaning out at an angle is just asking to catch a dock piling or a low branch.\u003c\/p\u003e\n\u003cp\u003eInstallation is honest work with a hole saw. You cut a 2 inch hole, drop the body through, and fasten it down. We always tell folks to run a backing plate, or at least a set of fender washers under the deck, if the fiberglass or aluminum is on the thin side. A rod loaded up with a heavy jig and a stiff wind puts real strain on the mount, and you want that load spread out. Mounting hardware isn't called out in the product data, so plan on a few stainless screws or through-bolts sized to your deck. Snug them down evenly so the trim cap seats flat, and you're done.\u003c\/p\u003e\n\u003cp\u003eThe 2 inch hole is a common standard, so if you're replacing an older holder that's gone brittle from years of UV, there's a good chance this one drops straight into the existing cutout with no new drilling. Measure first. If your old hole is a touch smaller, a step bit or hole saw opens it up in a minute. If it's larger, you'll want a bigger holder or a trim ring to close the gap cleanly.\u003c\/p\u003e\n\u003cp\u003eDepth matters too. At 9-1\/2 inches overall, the tube runs deep enough to hold a rod butt securely without letting things rock around up top. That length also means you need clearance under the deck, so check for wiring, hoses, or the side of a livewell before you commit to a spot. A quick reach-under with your hand saves a lot of aggravation later.\u003c\/p\u003e\n\u003cp\u003eWhere does this one earn its keep? Think vertical rod storage along the gunwale of a bass boat or a center console. Think a bank of them across the transom or along a pontoon rail, so everybody aboard has a home for their rod between spots. Anglers who fish with friends love having a dedicated spot per person. The white finish is a clean match for most gelcoat, and it looks just as right on a painted aluminum jon boat. It's not a trolling holder, since the rod sits straight up instead of kicked out to the side. If you're setting a spread, you'll want an angled holder for that job. But for holding, transporting, and keeping the deck organized, this is the one to reach for.\u003c\/p\u003e\n\u003cp\u003eEach holder takes one rod, which keeps things simple and lets you place them exactly where you need them rather than committing to a fixed multi-rod rack. Space a run of them about a rod-width apart and you've got a tidy line that won't tangle. As for upkeep, there really isn't any. Give it a rinse when you rinse the boat, and that's it.\u003c\/p\u003e\n\u003cp\u003eThere's not much that can go wrong with a part like this. One piece, one job, and it keeps doing it season after season in salt and sun. Buy a couple, put them where your hands actually reach, and you'll wonder how you got along without them.\u003c\/p\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eKey Features\u003c\/h2\u003e\n\u003cul class=\"nvn-features\"\u003e\n  \u003cli\u003e90 degree flat-top design holds a single rod straight up and down for clean vertical storage\u003c\/li\u003e\n  \u003cli\u003eFlush mount body drops into a standard 2 inch diameter hole\u003c\/li\u003e\n  \u003cli\u003e9-1\/2 inch overall length seats the rod butt securely below the deck\u003c\/li\u003e\n  \u003cli\u003eFlat trim cap finishes flush with the surface, nothing to snag a line or catch a toe\u003c\/li\u003e\n  \u003cli\u003eWhite finish matches most gelcoat and painted aluminum\u003c\/li\u003e\n  \u003cli\u003eSingle rod capacity lets you place holders exactly where you reach for them\u003c\/li\u003e\n  \u003cli\u003eOne-piece build stands up to salt and sun with just a freshwater rinse\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"nvn-trust\"\u003e\n  \u003ch2\u003eWhy Buy from NVN Marine\u003c\/h2\u003e\n  \u003cul\u003e\n    \u003cli\u003eAuthorized T-H Marine Supplies reseller, full manufacturer warranty\u003c\/li\u003e\n    \u003cli\u003eNMEA member and ABYC certified, advice from real boat techs\u003c\/li\u003e\n    \u003cli\u003eSame-day shipping before 3 PM ET on in-stock items\u003c\/li\u003e\n    \u003cli\u003eNY headquarters and Fort Lauderdale flagship retail store\u003c\/li\u003e\n  \u003c\/ul\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eFrequently Asked Questions\u003c\/h2\u003e\n\u003cdiv class=\"nvn-faq\"\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhat size hole does this rod holder need?\u003c\/summary\u003e\n    \u003cp\u003eIt drops into a 2 inch diameter hole. Cut it with a hole saw, drop the body through, and fasten it down.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eHow long is the holder?\u003c\/summary\u003e\n    \u003cp\u003e9-1\/2 inches overall. Most of that sits below the deck, so plan for clearance underneath before you pick a spot.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eAt what angle does it hold the rod?\u003c\/summary\u003e\n    \u003cp\u003e90 degrees, so the rod stands straight up and down. That's ideal for storage and transport, not for setting a trolling spread.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eHow many rods does it hold?\u003c\/summary\u003e\n    \u003cp\u003eOne. Each holder takes a single rod, which lets you place them exactly where you want them.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhat color is it?\u003c\/summary\u003e\n    \u003cp\u003eWhite. It's a clean match for most gelcoat and looks right on painted aluminum too.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eIs a fishing rod included?\u003c\/summary\u003e\n    \u003cp\u003eNo. This is the rod holder only. The rod itself isn't part of the package.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eDoes it come with mounting hardware?\u003c\/summary\u003e\n    \u003cp\u003eMounting hardware isn't listed in the product data, so plan on supplying your own stainless screws or through-bolts sized to your deck. We recommend a backing plate or fender washers on thin decks.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhere can I mount it?\u003c\/summary\u003e\n    \u003cp\u003eAnywhere you've got a flat surface and clearance below. The gunwale, deck, console, transom, or a pontoon rail are all common spots. It's a flush mount, so the top finishes even with the surface.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eCan I use it for trolling?\u003c\/summary\u003e\n    \u003cp\u003eIt holds the rod vertical at 90 degrees, so it's built for storage and transport rather than trolling. For a trolling spread you'll want an angled holder.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWill it hold up in salt water?\u003c\/summary\u003e\n    \u003cp\u003eIt's built for saltwater use. Give it a freshwater rinse when you rinse the boat and it'll last for years.\u003c\/p\u003e\n  \u003c\/details\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eTechnical Specifications\u003c\/h2\u003e\n\u003ctable class=\"nvn-specs\"\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n\u003cth\u003eTitle\u003c\/th\u003e\n\u003ctd\u003eT-H Marine 90 Degree Flush Mount Rod Holder, Flat Top, White\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eBrand\u003c\/th\u003e\n\u003ctd\u003eT-H Marine\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eManufacturer Part Number\u003c\/th\u003e\n\u003ctd\u003eRH-2FW-DP\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eUPC\u003c\/th\u003e\n\u003ctd\u003e733572011951\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eProduct Type\u003c\/th\u003e\n\u003ctd\u003eFlush Mount Rod Holder\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eMount Type\u003c\/th\u003e\n\u003ctd\u003eFlush Mount\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eRod Angle\u003c\/th\u003e\n\u003ctd\u003e90 Degrees (vertical)\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eTop Style\u003c\/th\u003e\n\u003ctd\u003eFlat Top\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eRod Capacity\u003c\/th\u003e\n\u003ctd\u003e1 Rod\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eColor\u003c\/th\u003e\n\u003ctd\u003eWhite\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eOverall Length\u003c\/th\u003e\n\u003ctd\u003e9-1\/2 in\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eMounting Hole Diameter\u003c\/th\u003e\n\u003ctd\u003e2 in\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003cscript type=\"application\/ld+json\"\u003e\n{\n    \"@context\": \"https:\/\/schema.org\",\n    \"@type\": \"FAQPage\",\n    \"mainEntity\": [\n        {\n            \"@type\": \"Question\",\n            \"name\": \"What size hole does this rod holder need?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"It drops into a 2 inch diameter hole. Cut it with a hole saw, drop the body through, and fasten it down.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"How long is the holder?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"9-1\/2 inches overall. Most of that sits below the deck, so plan for clearance underneath before you pick a spot.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"At what angle does it hold the rod?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"90 degrees, so the rod stands straight up and down. That's ideal for storage and transport, not for setting a trolling spread.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"How many rods does it hold?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"One. Each holder takes a single rod, which lets you place them exactly where you want them.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"What color is it?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"White. It's a clean match for most gelcoat and looks right on painted aluminum too.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Is a fishing rod included?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"No. This is the rod holder only. The rod itself isn't part of the package.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Does it come with mounting hardware?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Mounting hardware isn't listed in the product data, so plan on supplying your own stainless screws or through-bolts sized to your deck. We recommend a backing plate or fender washers on thin decks.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Where can I mount it?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Anywhere you've got a flat surface and clearance below. The gunwale, deck, console, transom, or a pontoon rail are all common spots. It's a flush mount, so the top finishes even with the surface.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Can I use it for trolling?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"It holds the rod vertical at 90 degrees, so it's built for storage and transport rather than trolling. For a trolling spread you'll want an angled holder.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Will it hold up in salt water?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"It's built for saltwater use. Give it a freshwater rinse when you rinse the boat and it'll last for years.\"\n            }\n        }\n    ]\n}\n\u003c\/script\u003e\n","brand":"T-H Marine","offers":[{"title":"Default Title","offer_id":45097283616861,"sku":"2010892","price":9.69,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0299\/7266\/0317\/files\/ImageServerAPI_5101e4a9-ca80-4a39-a415-d7485e041693.jpg?v=1790326171","url":"https:\/\/nvnmarine.com\/products\/t-h-marine-90-degree-flush-mount-rod-holder-white","provider":"NVN Marine","version":"1.0","type":"link"}