{"product_id":"sierra-18-8152-10-1-4-vinyl-fuel-line-10-ft-roll","title":"Sierra 18-8152-10 1\/4\" Vinyl Fuel Line, 10 ft Roll","description":"\u003cp class=\"nvn-hero\"\u003eSierra's 18-8152-10 is a 10 foot roll of 1\/4 inch vinyl fuel line for gasoline, sized to fit the barbs on portable tanks, primer bulbs, and small outboards. Yellow vinyl, 3\/8 inch outside diameter, rated to 35 PSI. Universal fit, so you cut what you need, clamp both ends, and get a tired fuel run breathing again.\u003c\/p\u003e\n\n\u003cdiv class=\"nvn-description\"\u003e\n\u003cp\u003eThis is Sierra's 18-8152-10 vinyl fuel line, a 10 foot roll of 1\/4 inch inside diameter hose that's a handy thing to keep in the boat's spares bin. It's yellow vinyl with a 3\/8 inch outside diameter, and it's built for gasoline. Universal fit, so it works across a lot of small marine setups without hunting down an exact OEM part number.\u003c\/p\u003e\n\u003cp\u003eThe 1\/4 inch inside diameter is the size you'll see on a ton of portable tank hookups, primer bulb runs, and small outboard fuel feeds. If your old line has gone stiff, cracked at the barb, or just looks tired, this gives you a fresh 10 foot length to cut from. Ten feet is usually plenty to redo a portable tank hose and still have some left over for a vent line or a second job later in the season.\u003c\/p\u003e\n\u003cp\u003eWhere does it fit best? Think portable six gallon tanks, primer bulb assemblies, tank vent lines, and the fuel runs on smaller kickers and outboards in the 6 to 25 horse range. It's a utility line, the kind you reach for when you need to get a small engine fed and running again. For a permanent, sealed below deck fuel feed on a bigger boat, you want hose that carries the proper USCG and SAE rating for that job. Know what you're using it for and it'll do its part.\u003c\/p\u003e\n\u003cp\u003eA word on fuel. This line is made for gasoline. It is not intended for diesel. The working pressure is rated at 35 PSI, which covers the low pressure suction and feed side of a carbureted outboard or a portable tank setup. It is not a high pressure EFI supply line, so don't put it on the pressure side of a fuel injection system. Match the hose to the job and you're in good shape.\u003c\/p\u003e\n\u003cp\u003eInstall is straightforward. Cut it clean and square with a sharp knife or a hose cutter so the end seats fully on the barb. Push it all the way onto the fitting, then secure every connection with a proper hose clamp. Vinyl line can back off a barbed fitting if it's just pushed on, so clamp both ends. On anything that sees vibration or heat near the engine, a lot of us run a second clamp for peace of mind. Keep runs as short as the layout allows and support long spans so the line isn't hanging on the fittings.\u003c\/p\u003e\n\u003cp\u003eNow the honest part, because we'd rather you know. Vinyl fuel line is a great budget utility hose, but it does age. Over a couple of seasons, especially with today's ethanol blended pump gas and plenty of sun, vinyl can stiffen, discolor, or get brittle at the ends. That's normal for the material. Inspect it each spring, flex it in your hands, and if it's hard, cracked, or weeping at a fitting, cut it back or replace it. Keeping it out of constant direct sunlight and cutting it to the length you actually need both help it last. Treat it as a serviceable part, not a forever part, and it'll keep your small rig running clean.\u003c\/p\u003e\n\u003cp\u003eSierra has been supplying marine replacement parts to boaters and OEM builders for decades, and their catalog covers the everyday consumables that keep engines fed, sealed, and running. This 10 foot roll is one of those grab and go items worth keeping aboard. Whether you're rigging a portable tank for the tender, freshening up the fuel run on a small outboard, or replacing a cracked vent line, it's a simple, universal fix at a fair price. Cut what you need, clamp it down, and get back on the water.\u003c\/p\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eKey Features\u003c\/h2\u003e\n\u003cul class=\"nvn-features\"\u003e\n  \u003cli\u003e1\/4 inch inside diameter and 3\/8 inch outside diameter, sized to fit the barbs on most portable tanks, primer bulbs, and small outboard fuel runs\u003c\/li\u003e\n  \u003cli\u003e10 foot roll gives you enough length to redo a tank hose and still have line left over for a vent or a spare job\u003c\/li\u003e\n  \u003cli\u003e35 PSI working pressure suits the low pressure feed and suction side of carbureted outboards and portable tanks\u003c\/li\u003e\n  \u003cli\u003eYellow vinyl construction is easy to route and easy to spot when you're tracing a line in a crowded bilge\u003c\/li\u003e\n  \u003cli\u003eRated for gasoline, not for diesel, so it's an easy match for most small marine gas engines\u003c\/li\u003e\n  \u003cli\u003eUniversal fit means no chasing an exact OEM part number, just cut it to length and clamp it on\u003c\/li\u003e\n  \u003cli\u003eSierra marine replacement part, MPN 18-8152-10, from a brand that supplies OEM engine builders and boat manufacturers\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"nvn-trust\"\u003e\n  \u003ch2\u003eWhy Buy from NVN Marine\u003c\/h2\u003e\n  \u003cul\u003e\n    \u003cli\u003eAuthorized Sierra Marine reseller, full manufacturer warranty\u003c\/li\u003e\n    \u003cli\u003eNMEA member and ABYC certified, advice from real boat techs\u003c\/li\u003e\n    \u003cli\u003eSame-day shipping before 3 PM ET on in-stock items\u003c\/li\u003e\n    \u003cli\u003eNY headquarters and Fort Lauderdale flagship retail store\u003c\/li\u003e\n  \u003c\/ul\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eFrequently Asked Questions\u003c\/h2\u003e\n\u003cdiv class=\"nvn-faq\"\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhat size is this fuel line?\u003c\/summary\u003e\n    \u003cp\u003eIt's 1\/4 inch inside diameter with a 3\/8 inch outside diameter. That 1\/4 inch ID is the common size for portable tank hookups, primer bulb runs, and many small outboard fuel feeds.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eHow much line comes on the roll?\u003c\/summary\u003e\n    \u003cp\u003eYou get a 10 foot roll. That's usually plenty to redo a portable tank hose and still have some length left for a vent line or another small job.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhat is the working pressure rating?\u003c\/summary\u003e\n    \u003cp\u003eIt's rated at 35 PSI. That covers the low pressure feed and suction side of a carbureted outboard or a portable tank setup. It is not a high pressure line for the supply side of a fuel injection system.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eCan I use this line with diesel fuel?\u003c\/summary\u003e\n    \u003cp\u003eNo. This vinyl line is made for gasoline and is not intended for diesel fuel. Use a hose rated for diesel on a diesel engine.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eIs it okay with today's ethanol blended pump gas?\u003c\/summary\u003e\n    \u003cp\u003eIt handles gasoline, including common E10 pump gas, for its service life. Vinyl does age faster with ethanol blends and sun exposure, so inspect it each season and replace it once it stiffens, discolors, or cracks at the ends.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhat can I use this fuel line for?\u003c\/summary\u003e\n    \u003cp\u003eIt's a universal utility line for portable fuel tanks, primer bulb assemblies, tank vent lines, and the fuel runs on smaller kickers and outboards in the 6 to 25 horse range.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eDo I need hose clamps?\u003c\/summary\u003e\n    \u003cp\u003eYes. Push the line fully onto the barb and clamp every connection. Vinyl can back off a barbed fitting if it's only pushed on, so clamp both ends, and add a second clamp anywhere there's vibration or heat.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eIs this a universal fit?\u003c\/summary\u003e\n    \u003cp\u003eYes. It's sold by inside diameter rather than by a specific engine part number, so you cut it to the length you need and clamp it to your fittings.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eIs vinyl line suitable for a permanent below deck fuel feed?\u003c\/summary\u003e\n    \u003cp\u003eIt's best used as a utility line for portable tanks, vents, and short accessible runs. For a permanent, sealed below deck fuel feed on a larger boat, choose hose carrying the proper USCG and SAE rating for that application.\u003c\/p\u003e\n  \u003c\/details\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eTechnical Specifications\u003c\/h2\u003e\n\u003ctable class=\"nvn-specs\"\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n\u003cth\u003eTitle\u003c\/th\u003e\n\u003ctd\u003eSierra 18-8152-10 Vinyl Fuel Line, 1\/4 Inch ID, 10 Foot Roll\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eBrand\u003c\/th\u003e\n\u003ctd\u003eSierra Marine\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eManufacturer Part Number\u003c\/th\u003e\n\u003ctd\u003e18-8152-10\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eUPC\u003c\/th\u003e\n\u003ctd\u003e808282267247\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e10 Feet\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eInside Diameter\u003c\/th\u003e\n\u003ctd\u003e1\/4 Inch\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eOutside Diameter\u003c\/th\u003e\n\u003ctd\u003e3\/8 Inch\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eWorking Pressure\u003c\/th\u003e\n\u003ctd\u003e35 PSI\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eColor\u003c\/th\u003e\n\u003ctd\u003eYellow\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eVinyl\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eFuel Compatibility\u003c\/th\u003e\n\u003ctd\u003eGasoline (Not Intended For Diesel Fuel)\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eFitment\u003c\/th\u003e\n\u003ctd\u003eUniversal\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eProduct Type\u003c\/th\u003e\n\u003ctd\u003eVinyl Fuel Line\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003cscript type=\"application\/ld+json\"\u003e\n{\n    \"@context\": \"https:\/\/schema.org\",\n    \"@type\": \"FAQPage\",\n    \"mainEntity\": [\n        {\n            \"@type\": \"Question\",\n            \"name\": \"What size is this fuel line?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"It's 1\/4 inch inside diameter with a 3\/8 inch outside diameter. That 1\/4 inch ID is the common size for portable tank hookups, primer bulb runs, and many small outboard fuel feeds.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"How much line comes on the roll?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"You get a 10 foot roll. That's usually plenty to redo a portable tank hose and still have some length left for a vent line or another small job.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"What is the working pressure rating?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"It's rated at 35 PSI. That covers the low pressure feed and suction side of a carbureted outboard or a portable tank setup. It is not a high pressure line for the supply side of a fuel injection system.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Can I use this line with diesel fuel?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"No. This vinyl line is made for gasoline and is not intended for diesel fuel. Use a hose rated for diesel on a diesel engine.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Is it okay with today's ethanol blended pump gas?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"It handles gasoline, including common E10 pump gas, for its service life. Vinyl does age faster with ethanol blends and sun exposure, so inspect it each season and replace it once it stiffens, discolors, or cracks at the ends.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"What can I use this fuel line for?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"It's a universal utility line for portable fuel tanks, primer bulb assemblies, tank vent lines, and the fuel runs on smaller kickers and outboards in the 6 to 25 horse range.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Do I need hose clamps?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Yes. Push the line fully onto the barb and clamp every connection. Vinyl can back off a barbed fitting if it's only pushed on, so clamp both ends, and add a second clamp anywhere there's vibration or heat.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Is this a universal fit?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Yes. It's sold by inside diameter rather than by a specific engine part number, so you cut it to the length you need and clamp it to your fittings.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Is vinyl line suitable for a permanent below deck fuel feed?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"It's best used as a utility line for portable tanks, vents, and short accessible runs. For a permanent, sealed below deck fuel feed on a larger boat, choose hose carrying the proper USCG and SAE rating for that application.\"\n            }\n        }\n    ]\n}\n\u003c\/script\u003e\n","brand":"Sierra Marine","offers":[{"title":"Default Title","offer_id":45072317382749,"sku":"2009206","price":48.69,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0299\/7266\/0317\/files\/ImageServerAPI_9817775f-7356-40b8-a981-853bf4459a88.jpg?v=1789737277","url":"https:\/\/nvnmarine.com\/products\/sierra-18-8152-10-1-4-vinyl-fuel-line-10-ft-roll","provider":"NVN Marine","version":"1.0","type":"link"}