Sea-Dog 18 AWG Red Primary Wire 250 ft | 8018024
Sea-Dog 18 AWG Red Primary Wire 250 ft | 8018024 — Product description
A full 250 foot spool of Sea-Dog 18 AWG red primary wire. It's a good fit for low-draw DC circuits like gauges, lights and switch leads, and it's enough length to finish the job without a second trip.
This is a 250 foot spool of Sea-Dog 18 AWG red primary wire, and it's the kind of thing you want on the shelf before the project starts. Nothing slows a wiring job down like running out of wire three feet short of the switch. A full 250 feet gives you room to do the whole job and still have some left over.
18 AWG is a light-gauge size. It's a natural fit for low-draw circuits on a boat, like indicator lights, gauges, switch signal leads, small accessories and control wiring. It isn't meant for big loads. Bilge pumps, windlasses, trolling motors and anything pulling serious amperage need heavier wire, so size your run to the load before you cut. If you're not sure, check the amp draw of the device and the length of the run, then match them to a wire gauge chart.
Red is the traditional color for positive on a DC system, so this spool makes it easy to keep your wiring readable. Pair it with a black or other color spool for the return side and the next person to open the panel, which might be you, will thank you for it. Good color discipline is one of those small habits that saves real troubleshooting time out on the water.
Because it's sold as a single-conductor spool, you cut it to the exact lengths you need. That makes it handy for rewiring a console, adding a few accessories at the helm, running a new set of switch leads, or just keeping a spool in the shop for repairs. We can't tell you more about the insulation or conductor construction than the part number and title give us, so if a job calls for a specific rating or standard, confirm it with Sea-Dog before you buy. Sea-Dog part number 8018024.
A few quick tips. Use proper crimp terminals sized for 18 AWG. Seal your connections where they might see moisture. And support the wire so it doesn't chafe against sharp edges. Do those three things and a simple wire run will outlast the boat's next few seasons.
Key Features
- 18 AWG gauge for low-draw DC circuits like lights, gauges and switch leads
- Red insulation color, the usual choice for positive leads
- 250 foot spool, enough for a whole rewire
- Single-conductor primary wire you cut to length
- Sea-Dog part number 8018024
Why Buy from NVN Marine
- Authorized Sea-Dog reseller, full manufacturer warranty
- NMEA member and ABYC certified, advice from real boat techs
- Same-day shipping before 3 PM ET on in-stock items
- NY headquarters and Fort Lauderdale flagship retail store
Technical specifications
| Title | Sea-Dog 18 AWG Red Primary Wire - 250' |
|---|---|
| Brand | Sea-Dog |
| Manufacturer Part Number | 8018024 |
| UPC | 035514802826 |
| Wire Gauge | 18 AWG |
| Color | Red |
| Length | 250 ft |
| Wire Type | Primary Wire |
| Category | Electrical | Wire |
Frequently asked questions
What size is this wire?
It's 18 AWG, sold on a 250 foot spool in red.
What is it used for?
18 AWG primary wire suits low-draw DC circuits like indicator lights, gauges and switch leads. Match the gauge to your load and run length before you buy.
Can I use it for a bilge pump or trolling motor?
Not on its own. Higher-draw gear needs heavier wire. Check the device's amp draw and run length against a wire gauge chart.
How much wire is on the spool?
250 feet, so you can cut as many runs as the job needs.
What's the part number?
The Sea-Dog part number is 8018024 and the UPC is 035514802826.
Is it single conductor?
Yes, it's primary wire, a single conductor sold by the spool. Pair it with another color for the return side.