{"product_id":"railblaza-spooling-station-starport-line-spooler","title":"RAILBLAZA Spooling Station with StarPort Mount, Black","description":"\u003cp class=\"nvn-hero\"\u003eRespooling a reel by yourself is a pain. The RAILBLAZA Spooling Station fixes that. It holds one filler spool up to 4.3 inches across and 2 inches thick, feeds line with even tension, and mounts two ways: screw it down as a fixed station, or clip it onto a RAILBLAZA StarPort with the included adapter. Simple, tough, and it lives on the boat or the bench.\u003c\/p\u003e\n\n\u003cdiv class=\"nvn-description\"\u003e\n\u003cp\u003eRespooling line at the dock shouldn't mean pinning a spool between your knees or roping a buddy into holding it steady. The RAILBLAZA Spooling Station gives that spool a solid home so you can wind fresh line onto a reel cleanly, with even tension, by yourself. It's a simple piece of gear that solves a genuinely annoying job.\u003c\/p\u003e\n\u003cp\u003eThe station holds one spool up to 2 inches thick and 4.3 inches in maximum diameter. That covers most of the mono, fluoro, and braid filler spools you'll pick up at the tackle shop. The spool sits on a fixed post so it feeds line smoothly as you crank, and there's enough drag from the mount to keep the line from backlashing off the spool while you work.\u003c\/p\u003e\n\u003cp\u003eHere's why that matters. Line that goes on under uneven tension buries into itself on the reel, and that's exactly what causes wind knots and dig-in later out on the water. Keeping the spool captured and turning smoothly lets you thumb light pressure on the line and lay it down tight and even. Do it right once at the dock and you'll fight fewer tangles all season.\u003c\/p\u003e\n\u003cp\u003eYou get two ways to mount it. Screw it down as a fixed mount using the two stainless steel self-tapping screws that come in the box, and it becomes a permanent spooling spot on a workbench, a bait station, or a garage wall. Or drop it onto a RAILBLAZA StarPort using the included StarPort adapter, and it becomes part of your modular RAILBLAZA setup. That means you can pop it into any StarPort base you've already got mounted on the boat, use it, then pull it and swap in a rod holder or a light. One accessory, a hundred places to run it.\u003c\/p\u003e\n\u003cp\u003eThe whole body is molded from UV-stabilized, fiberglass-reinforced plastic. So it handles sun and salt without getting brittle, and the fiberglass fill gives it the stiffness to take the load of a full spool without flexing. It's finished in black to keep it low-key on the deck. A quick rinse after a salty day and it'll last for years.\u003c\/p\u003e\n\u003cp\u003eWho's this for? Anglers who respool their own reels and are tired of the two-hand wrestling match. Kayak fishermen who already run RAILBLAZA StarPorts and want a spooling spot that clicks into the same tracks. Center console owners running downriggers who need a tidy place to wind leader and backing. And honestly, anyone with a home tackle bench who wants respooling to stop being a chore. If you switch between mono and braid setups a lot, having a dedicated spooling spot ready to go saves you real time.\u003c\/p\u003e\n\u003cp\u003eA couple of install notes worth knowing. If you're screwing it straight into gelcoat or a thin deck, pre-drill your pilot holes before running the self-tappers. That keeps the gelcoat from cracking around the fasteners. On a soft or flexy hull, back the mount with a small plate or a fender washer so a full, heavy spool doesn't work the screws loose over time. And when you load a 2-inch-thick spool, center it on the post. The thicker spools can slip a little if they're cocked to one side.\u003c\/p\u003e\n\u003cp\u003eKnow the limits before you buy. The 4.3-inch maximum diameter covers standard filler spools, but some of the big bulk braid spools run larger than that and won't fit. Check your spool's diameter if you buy line in bulk. And the black finish, while UV-stabilized, can start to chalk after a couple of hard seasons in strong tropical sun, so an occasional wipe-down keeps it looking right.\u003c\/p\u003e\n\u003cp\u003eBottom line, it's an inexpensive fix for a job every angler deals with. Mount it once, or run it on your StarPorts, and respooling turns into a one-person, five-minute task instead of a fight.\u003c\/p\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eKey Features\u003c\/h2\u003e\n\u003cul class=\"nvn-features\"\u003e\n  \u003cli\u003eHolds one spool up to 2 inches thick and 4.3 inches in diameter, covering most mono, fluoro, and braid filler spools\u003c\/li\u003e\n  \u003cli\u003eTwo mounting options: fixed-mount with the included stainless screws, or clip onto any RAILBLAZA StarPort with the included adapter\u003c\/li\u003e\n  \u003cli\u003eUV-stabilized, fiberglass-reinforced plastic body shrugs off sun and salt without going brittle\u003c\/li\u003e\n  \u003cli\u003eFixed feed post keeps the spool captured and turning smoothly so you wind on with even tension\u003c\/li\u003e\n  \u003cli\u003eIncludes 1 StarPort adapter and 2 stainless steel self-tapping screws, ready to mount out of the box\u003c\/li\u003e\n  \u003cli\u003eBlack finish keeps it low-profile on the deck or bench\u003c\/li\u003e\n  \u003cli\u003eSwaps in and out of existing StarPort bases so one accessory works all over the boat\u003c\/li\u003e\n  \u003cli\u003eCompact footprint fits a tackle bench, bait station, garage wall, or kayak track\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"nvn-trust\"\u003e\n  \u003ch2\u003eWhy Buy from NVN Marine\u003c\/h2\u003e\n  \u003cul\u003e\n    \u003cli\u003eAuthorized RAILBLAZA reseller, full manufacturer warranty\u003c\/li\u003e\n    \u003cli\u003eNMEA member and ABYC certified, advice from real boat techs\u003c\/li\u003e\n    \u003cli\u003eSame-day shipping before 3 PM ET on in-stock items\u003c\/li\u003e\n    \u003cli\u003eNY headquarters and Fort Lauderdale flagship retail store\u003c\/li\u003e\n  \u003c\/ul\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eFrequently Asked Questions\u003c\/h2\u003e\n\u003cdiv class=\"nvn-faq\"\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhat size spools does it hold?\u003c\/summary\u003e\n    \u003cp\u003eOne spool at a time, up to 2 inches thick and 4.3 inches in maximum diameter. That covers most standard mono, fluoro, and braid filler spools from the tackle shop.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eHow does it mount?\u003c\/summary\u003e\n    \u003cp\u003eTwo ways. Screw it down as a fixed mount with the two included stainless steel self-tapping screws, or clip it onto a RAILBLAZA StarPort base using the included StarPort adapter.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eDoes the StarPort adapter come with it?\u003c\/summary\u003e\n    \u003cp\u003eYes. The box includes one StarPort adapter and two stainless steel self-tapping screws. If you want to run it on the StarPort system, the StarPort base itself is a separate RAILBLAZA part. The fixed-mount option needs no base.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWill big bulk braid spools fit?\u003c\/summary\u003e\n    \u003cp\u003eThe station handles spools up to 4.3 inches in diameter. Some of the larger bulk braid spools run bigger than that and won't fit, so check your spool's diameter if you buy line in bulk.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhat's it made of?\u003c\/summary\u003e\n    \u003cp\u003eUV-stabilized, fiberglass-reinforced plastic. The UV stabilizer helps it resist sun fade, and the fiberglass fill gives it the stiffness to hold a full spool without flexing.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eCan I mount it on a kayak?\u003c\/summary\u003e\n    \u003cp\u003eYes, through the StarPort adapter if you already run RAILBLAZA StarPorts. On a soft or flexy hull, back the mount with a small plate or fender washer so a heavy full spool doesn't work the screws loose.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eDo I need to pre-drill for the screws?\u003c\/summary\u003e\n    \u003cp\u003eOn gelcoat or a thin deck, yes. Pre-drilling pilot holes before running the self-tappers keeps the gelcoat from cracking around the fasteners.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eCan I take it off when I'm not using it?\u003c\/summary\u003e\n    \u003cp\u003eIf it's on a StarPort, yes. Pop it out and swap in a rod holder, light, or another RAILBLAZA accessory in the same base. A fixed-mount install stays put.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhy use a spooling station instead of holding the spool by hand?\u003c\/summary\u003e\n    \u003cp\u003eA captured, freely turning spool lets you keep even tension on the line as you wind. That lays line onto the reel tight and even, which means fewer wind knots and less dig-in later on the water.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhat color is it?\u003c\/summary\u003e\n    \u003cp\u003eBlack. It's a low-profile look that blends in on most decks and benches.\u003c\/p\u003e\n  \u003c\/details\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eTechnical Specifications\u003c\/h2\u003e\n\u003ctable class=\"nvn-specs\"\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n\u003cth\u003eTitle\u003c\/th\u003e\n\u003ctd\u003eRAILBLAZA Spooling Station with StarPort Mount, Black\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eBrand\u003c\/th\u003e\n\u003ctd\u003eRAILBLAZA\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eManufacturer Part Number\u003c\/th\u003e\n\u003ctd\u003e09-4159-11\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eUPC\u003c\/th\u003e\n\u003ctd\u003e814162021779\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eColor\u003c\/th\u003e\n\u003ctd\u003eBlack\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003eUV Stabilized Fiberglass Reinforced Plastic\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eSpool Capacity\u003c\/th\u003e\n\u003ctd\u003e1 spool\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eMaximum Spool Thickness\u003c\/th\u003e\n\u003ctd\u003e2 in\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eMaximum Spool Diameter\u003c\/th\u003e\n\u003ctd\u003e4.3 in\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eMounting Options\u003c\/th\u003e\n\u003ctd\u003eFixed Mount or StarPort Mount\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eIncluded Adapter\u003c\/th\u003e\n\u003ctd\u003e1 StarPort Adapter\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eIncluded Fasteners\u003c\/th\u003e\n\u003ctd\u003e2 Stainless Steel Self-Tapping Screws\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003cscript type=\"application\/ld+json\"\u003e\n{\n    \"@context\": \"https:\/\/schema.org\",\n    \"@type\": \"FAQPage\",\n    \"mainEntity\": [\n        {\n            \"@type\": \"Question\",\n            \"name\": \"What size spools does it hold?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"One spool at a time, up to 2 inches thick and 4.3 inches in maximum diameter. That covers most standard mono, fluoro, and braid filler spools from the tackle shop.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"How does it mount?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Two ways. Screw it down as a fixed mount with the two included stainless steel self-tapping screws, or clip it onto a RAILBLAZA StarPort base using the included StarPort adapter.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Does the StarPort adapter come with it?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Yes. The box includes one StarPort adapter and two stainless steel self-tapping screws. If you want to run it on the StarPort system, the StarPort base itself is a separate RAILBLAZA part. The fixed-mount option needs no base.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Will big bulk braid spools fit?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"The station handles spools up to 4.3 inches in diameter. Some of the larger bulk braid spools run bigger than that and won't fit, so check your spool's diameter if you buy line in bulk.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"What's it made of?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"UV-stabilized, fiberglass-reinforced plastic. The UV stabilizer helps it resist sun fade, and the fiberglass fill gives it the stiffness to hold a full spool without flexing.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Can I mount it on a kayak?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Yes, through the StarPort adapter if you already run RAILBLAZA StarPorts. On a soft or flexy hull, back the mount with a small plate or fender washer so a heavy full spool doesn't work the screws loose.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Do I need to pre-drill for the screws?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"On gelcoat or a thin deck, yes. Pre-drilling pilot holes before running the self-tappers keeps the gelcoat from cracking around the fasteners.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Can I take it off when I'm not using it?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"If it's on a StarPort, yes. Pop it out and swap in a rod holder, light, or another RAILBLAZA accessory in the same base. A fixed-mount install stays put.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Why use a spooling station instead of holding the spool by hand?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"A captured, freely turning spool lets you keep even tension on the line as you wind. That lays line onto the reel tight and even, which means fewer wind knots and less dig-in later on the water.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"What color is it?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Black. It's a low-profile look that blends in on most decks and benches.\"\n            }\n        }\n    ]\n}\n\u003c\/script\u003e\n","brand":"RAILBLAZA","offers":[{"title":"Default Title","offer_id":45051459207261,"sku":"2008628","price":35.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0299\/7266\/0317\/files\/ImageServerAPI_c2e8f3b7-fcbb-4ce9-a465-6f2b5d01f75b.jpg?v=1789388125","url":"https:\/\/nvnmarine.com\/products\/railblaza-spooling-station-starport-line-spooler","provider":"NVN Marine","version":"1.0","type":"link"}