{"product_id":"norcold-638374-ac-heating-element-for-polar-n7-n8-n10","title":"Norcold 638374 AC Heating Element for Polar N7 N8 N10 Fridges","description":"\u003cp class=\"nvn-hero\"\u003eThe Norcold 638374 is the 110-volt AC heating element for Polar Series N7, N8, and N10 refrigerators. If your fridge cools fine on gas but goes warm on shore power, this is almost always the part that failed. It's a genuine Norcold drop-in that mounts to the cooling unit and gets your electric mode working again.\u003c\/p\u003e\n\n\u003cdiv class=\"nvn-description\"\u003e\n\u003cp\u003eWhen a Norcold Polar fridge quits cooling on shore power but still runs fine on gas, the AC heating element is usually the part that let go. This is that element. The Norcold 638374 is the 110-volt AC heater for the N7, N8, and N10 Polar Series absorption refrigerators, and it's a direct replacement for the factory original.\u003c\/p\u003e\n\u003cp\u003eHere's what it does. A Norcold Polar fridge doesn't have a compressor. It's an absorption unit, so it makes cold by heating a sealed ammonia solution and letting it cycle through the cooling coils. When you're plugged into shore power or running the generator, this AC element is what supplies that heat. Off the grid, the fridge switches to LP gas and a separate burner takes over. So if your box chills down fine on propane but goes warm the moment you plug in, the electric side has failed, and most of the time that's the heating element. The board and the gas side are almost always fine when that's the symptom.\u003c\/p\u003e\n\u003cp\u003eBefore you order, it's worth being sure the element is the culprit. Two things fail on the electric side of these fridges, the heater and the board that feeds it. Pulling the two leads and reading the element with a meter settles it in about a minute. A healthy element shows continuity. A dead one reads open and won't warm up no matter what the board sends it. If voltage is reaching the element and it still won't heat, this is your part. If nothing reaches it at all, look upstream at the fuse and the AC board first.\u003c\/p\u003e\n\u003cp\u003eThe 638374 fits the Polar N7, N8, and N10 families, and it's the same AC element used in the N611LT. If you're not sure which Norcold you've got, the model tag is usually inside the fridge on the upper liner or on a sticker behind the lower vent. Match the part number on your old element before you order. Norcold built these fridges in AC-only, DC, and dual-voltage versions, and the heaters aren't interchangeable. This one is the 110-volt AC part. If your old heater is stamped with a different number, order that one instead so you don't end up with a mismatch.\u003c\/p\u003e\n\u003cp\u003eSwapping it is a back-of-the-fridge job, not an inside-the-box one. Depending on your rig you'll reach it through the lower exterior vent or by sliding the fridge out. Kill the power first, both the shore cord and the 12-volt supply, and shut the gas off at the bottle before you touch anything. The element sits against the boiler tube of the cooling unit, held in place with a clamp or pocket, with two leads to disconnect. Old one out, new one in, leads back on, and you're back in business.\u003c\/p\u003e\n\u003cp\u003eOne thing this won't fix. If your fridge won't cool on gas either, or you catch a whiff of ammonia behind it, the sealed cooling unit itself has failed and a new heater won't bring it back. This is a repair part for a fridge with a good cooling unit and a dead electric heater, nothing more. But that's by far the most common failure, and when it's the element, this gets you back to plugging in at the campground and letting the fridge run quiet all night.\u003c\/p\u003e\n\u003cp\u003eIt's a genuine Norcold part, so it drops into the factory location without adapters or splicing. Just remember an absorption fridge is slow by design. Give it several hours to pull temperature down after the swap, and don't judge it by the first half hour. Once it's cold, this element will hold it there every time you're on power. That steady, quiet cold is the whole point of an absorption fridge, and a fresh element brings it right back.\u003c\/p\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eKey Features\u003c\/h2\u003e\n\u003cul class=\"nvn-features\"\u003e\n  \u003cli\u003e110-volt AC heating element that restores electric-mode cooling on Norcold Polar refrigerators\u003c\/li\u003e\n  \u003cli\u003eDirect fit for Polar Series N7, N8, and N10, and the same element used in the N611LT\u003c\/li\u003e\n  \u003cli\u003eGenuine Norcold replacement, drops into the factory location with no adapters or wire splicing\u003c\/li\u003e\n  \u003cli\u003eTwo-lead connection for a straightforward back-of-the-fridge swap\u003c\/li\u003e\n  \u003cli\u003eMounts against the cooling unit boiler tube where the original element sat\u003c\/li\u003e\n  \u003cli\u003eManufacturer part number 638374, UPC 610848166198 for exact matching against your old heater\u003c\/li\u003e\n  \u003cli\u003eFor absorption fridges that cool on LP gas but no longer cool on shore power\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"nvn-trust\"\u003e\n  \u003ch2\u003eWhy Buy from NVN Marine\u003c\/h2\u003e\n  \u003cul\u003e\n    \u003cli\u003eAuthorized Norcold reseller, full manufacturer warranty\u003c\/li\u003e\n    \u003cli\u003eNMEA member and ABYC certified, advice from real boat techs\u003c\/li\u003e\n    \u003cli\u003eSame-day shipping before 3 PM ET on in-stock items\u003c\/li\u003e\n    \u003cli\u003eNY headquarters and Fort Lauderdale flagship retail store\u003c\/li\u003e\n  \u003c\/ul\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eFrequently Asked Questions\u003c\/h2\u003e\n\u003cdiv class=\"nvn-faq\"\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhich refrigerators does the Norcold 638374 fit?\u003c\/summary\u003e\n    \u003cp\u003eIt's the 110-volt AC heating element for Norcold Polar Series N7, N8, and N10 refrigerators, and it's also the element used in the N611LT. Match the part number on your old heater before ordering to be sure.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eMy Norcold cools on gas but not on electric. Is this the part I need?\u003c\/summary\u003e\n    \u003cp\u003eUsually, yes. When an absorption fridge chills fine on LP but goes warm on shore power, the AC heating element has typically failed. Confirm by reading the element for continuity, an open reading means it needs replacing.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eIs this the AC element or the DC element?\u003c\/summary\u003e\n    \u003cp\u003eThis is the 110-volt AC element. Norcold built these fridges in AC-only, DC, and dual-voltage versions with different heaters that aren't interchangeable, so make sure your fridge uses the AC part before ordering.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eDo I have to pull the whole refrigerator to replace it?\u003c\/summary\u003e\n    \u003cp\u003eNot always. On many rigs you can reach the element through the lower exterior vent. On tighter installs you'll need to slide the fridge out. Either way it's a back-of-the-fridge job, not an inside-the-box one.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eCan I install this myself?\u003c\/summary\u003e\n    \u003cp\u003eIf you're comfortable disconnecting power and swapping two leads, yes. Shut off the shore cord, the 12-volt supply, and the LP gas first. The element sits against the cooling unit's boiler tube and comes off with a clamp or pocket.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eHow do I tell if it's the element or the control board?\u003c\/summary\u003e\n    \u003cp\u003eRead the element with a multimeter. Continuity means the heater is good and the problem is upstream at the fuse or AC board. No continuity means the element is open, and this is your part.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eHow long before the fridge gets cold after I replace it?\u003c\/summary\u003e\n    \u003cp\u003eAbsorption fridges cool slowly. Give it several hours to pull down to temperature, and don't judge it in the first half hour. Once it's cold it'll hold there whenever you're on power.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eIs this a genuine Norcold part?\u003c\/summary\u003e\n    \u003cp\u003eYes. The 638374 is a Norcold factory element that drops into the original location with no adapters or wire splicing.\u003c\/p\u003e\n  \u003c\/details\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eTechnical Specifications\u003c\/h2\u003e\n\u003ctable class=\"nvn-specs\"\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n\u003cth\u003eTitle\u003c\/th\u003e\n\u003ctd\u003eNorcold 638374 AC Heating Element for Polar N7\/N8\/N10\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eBrand\u003c\/th\u003e\n\u003ctd\u003eNorcold\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eManufacturer Part Number\u003c\/th\u003e\n\u003ctd\u003e638374\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eUPC\u003c\/th\u003e\n\u003ctd\u003e610848166198\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eVoltage\u003c\/th\u003e\n\u003ctd\u003e110 Volt AC\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eComponent Type\u003c\/th\u003e\n\u003ctd\u003eCooling Unit Heater Element\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eCompatible Series\u003c\/th\u003e\n\u003ctd\u003eNorcold Polar N7 \/ N8 \/ N10\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eAlso Fits\u003c\/th\u003e\n\u003ctd\u003eNorcold N611LT\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eRefrigerator Type\u003c\/th\u003e\n\u003ctd\u003eAbsorption (gas\/electric)\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003ePower Source\u003c\/th\u003e\n\u003ctd\u003eAC electric (shore power or generator)\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eApplication\u003c\/th\u003e\n\u003ctd\u003eRV \/ Motorhome Refrigerator\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eSold As\u003c\/th\u003e\n\u003ctd\u003eSingle element\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003cscript type=\"application\/ld+json\"\u003e\n{\n    \"@context\": \"https:\/\/schema.org\",\n    \"@type\": \"FAQPage\",\n    \"mainEntity\": [\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Which refrigerators does the Norcold 638374 fit?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"It's the 110-volt AC heating element for Norcold Polar Series N7, N8, and N10 refrigerators, and it's also the element used in the N611LT. Match the part number on your old heater before ordering to be sure.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"My Norcold cools on gas but not on electric. Is this the part I need?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Usually, yes. When an absorption fridge chills fine on LP but goes warm on shore power, the AC heating element has typically failed. Confirm by reading the element for continuity, an open reading means it needs replacing.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Is this the AC element or the DC element?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"This is the 110-volt AC element. Norcold built these fridges in AC-only, DC, and dual-voltage versions with different heaters that aren't interchangeable, so make sure your fridge uses the AC part before ordering.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Do I have to pull the whole refrigerator to replace it?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Not always. On many rigs you can reach the element through the lower exterior vent. On tighter installs you'll need to slide the fridge out. Either way it's a back-of-the-fridge job, not an inside-the-box one.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Can I install this myself?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"If you're comfortable disconnecting power and swapping two leads, yes. Shut off the shore cord, the 12-volt supply, and the LP gas first. The element sits against the cooling unit's boiler tube and comes off with a clamp or pocket.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"How do I tell if it's the element or the control board?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Read the element with a multimeter. Continuity means the heater is good and the problem is upstream at the fuse or AC board. No continuity means the element is open, and this is your part.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"How long before the fridge gets cold after I replace it?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Absorption fridges cool slowly. Give it several hours to pull down to temperature, and don't judge it in the first half hour. Once it's cold it'll hold there whenever you're on power.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Is this a genuine Norcold part?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Yes. The 638374 is a Norcold factory element that drops into the original location with no adapters or wire splicing.\"\n            }\n        }\n    ]\n}\n\u003c\/script\u003e\n","brand":"Norcold","offers":[{"title":"Default Title","offer_id":68069100585053,"sku":"2009137","price":44.69,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0299\/7266\/0317\/files\/ImageServerAPI_c0238db1-653e-49f5-a5e6-7f6c1e2b4ca7.jpg?v=1795117550","url":"https:\/\/nvnmarine.com\/products\/norcold-638374-ac-heating-element-for-polar-n7-n8-n10","provider":"NVN Marine","version":"1.0","type":"link"}