Navico DST-820 Plastic Thru-Hull Triducer Multisensor, 6M Cable
Navico DST-820 Plastic Thru-Hull Triducer Multisensor, 6M Cable — Product description
The Navico DST-820 is a plastic thru-hull multisensor that measures speed, depth, water temperature and heel and trim from a single 2-inch hole. It uses a Gen2 paddlewheel for accurate speed from under 0.3 knots up to 45 knots, and the 6 meter NMEA 2000 cable is already attached.
The Navico DST-820 puts speed, depth and water temperature into one plastic thru-hull sensor. Instead of cutting separate holes for a paddlewheel, a depth transducer and a temperature probe, you cut one 51 mm (2") hole and run one cable. That's less drilling below the waterline and a lot less to go wrong. The 6 m (20') NMEA 2000 cable comes with it, so once the sensor is bedded and in place you're ready to plug into your backbone.
Speed is where this sensor earns its keep. The Gen2 paddlewheel gives you precise start-up data below 0.3 knots, linear accuracy from 0.6 knots, and stable readings all the way to 45 knots. Speed output runs at 5.7 Hz, which is 5 times per second, so the number on your display moves smoothly instead of jumping around. Sailors know why that matters. Good speed through water helps you fine-tune sail trim and rig balance, and racers use it for accurate VMG and target speed calculations. Cruisers and anglers get a cleaner number for planning fuel and arrival times.
There's also an integrated attitude sensor inside. It reports heel and trim at 10 times per second, and that data feeds the more advanced calibration options. If your boat reads differently when it's heeled over than when it's sitting flat, you can enter manual speed values for multiple heel angles and up to 10 speeds. That kind of calibration used to mean expensive PC software. Now it's done from your phone.
Which brings us to setup. The DST-820 has Bluetooth BLE built in and works with the free CAST app for calibration. You scan a QR code, enter a one-time security password on your mobile device, and you're connected. It's built to meet UK PSTI security standards, so the link between the sensor and your phone is protected. Basic calibration is quick, and the advanced heel-compensated calibration is there when you want to dial it in properly. You can do it all from the cockpit, independent of your onboard instruments.
Depth runs from 0.5 m (1.6') to 100 m (330') with a 10° x 44° conventional beam, and the sensor reports water temperature from -10° to 40°C (14° to 104°F) with an accuracy of plus or minus 0.5°C. Depth updates once per second. Treat it as a navigation sensor that keeps you off the bottom and tells you what the water is doing. It's not meant to be a fish-finding transducer, so if your priority is sonar imaging, plan around that.
On the install side, the low profile housing is retractable and rated for a maximum deadrise angle of 22°. It's made for fiberglass or metal hulls, with a usable shaft length of 121 mm (4.75"). The hole size is the standard 51 mm (2"), and it's listed to fit most existing 2" housings, which makes it a practical upgrade if you're replacing an older sensor. Power is 9 to 16 VDC at 80 W rating, and the NMEA 2000 load equivalency number (LEN) is 2, so add that to your network power budget before you wire in.
A few practical notes before you order. Plan the cable route from the hull to your NMEA 2000 backbone ahead of time, and keep the 6 m length in mind when you pick a mounting spot. Mount it where the paddlewheel sits in clean, undisturbed water, away from strakes and other hull fittings. Once the boat's back in the water, check for leaks before you leave the dock, then run the app calibration on a calm day for the best results.
Who's it for? Cruising and racing sailboats, leisure yachts, and fishing boats that want accurate speed, depth and temperature on the same network. If you're replacing a tired paddlewheel and want a sensor that does more, this is a clean way to do it. Just remember the housing is plastic and the hull list is fiberglass or metal, so check your hull before you order. If you're not sure about fit or network connections, our crew is happy to talk it through before you cut anything.
Key Features
- Gen2 paddlewheel: precise speed data below 0.3 knots, linear from 0.6 knots, stable up to 45 knots
- 5.7 Hz speed output (5 times per second) for smooth, fast-updating speed through water
- Integrated attitude sensor reports heel and trim at 10 times per second
- Heel-compensated speed calibration with manual entries for multiple heel angles and up to 10 speeds
- Secure Bluetooth BLE connection to the CAST app, with QR-code setup and a one-time password
- Meets UK PSTI security standards for the sensor-to-phone connection
- Depth from 0.5 m (1.6') to 100 m (330') plus water temperature from -10° to 40°C
- Low profile retractable housing in plastic, fits a 51 mm (2") hole in fiberglass or metal hulls
- 6 m (20') NMEA 2000 cable, LEN 2, runs on 9 to 16 VDC
- Fits most existing 2" housings, so it works as a retrofit
Why Buy from NVN Marine
- Authorized Navico reseller, full manufacturer warranty
- NMEA member and ABYC certified, advice from real boat techs
- Same-day shipping before 3 PM ET on in-stock items
- NY headquarters and Fort Lauderdale flagship retail store
Technical specifications
| Title | Navico DST-820 Plastic Thru-Hull Triducer Multisensor w/6M Cable |
|---|---|
| Brand | Navico |
| Manufacturer Part Number | 000-15735-002 |
| UPC | 9420064142064 |
| Weight | 2.646 lbs |
| Package Dimensions (L x W x H) | 7.756 x 10.000 x 3.740 in |
| Country of Origin | United States |
| Functions | Depth, Speed, Temperature, Attitude |
| Mounting Style | Low Profile Thru-Hull |
| Protocol Output | NMEA 2000 |
| Housing | Plastic |
| Hull Material | Fiberglass or metal |
| Hole Size | 51 mm (2") |
| Max Deadrise Angle | 22° |
| Retractable Housing | Yes |
| Usable Shaft Length | 121 mm (4.75") |
| Acoustic Window | Urethane |
| Attitude Sensor | Yes |
| Bluetooth Capable | Yes, Bluetooth BLE |
| Cable Length | 6 m (20') NMEA 2000 cable |
| Power Rating | 80 W |
| Voltage | 9 to 16 VDC |
| NMEA 2000 LEN | 2 |
| Conventional Beam | 10° x 44° |
| Depth Range | 0.5 m (1.6') to 100 m (330') |
| Speed Range | Up to 45 knots |
| Data Rate | Depth: 1X/second, Speed: 5X/second, Heel/Trim: 10X/second |
| Pulses | 20,000 p/nm (5.6 Hz per knot) |
| Water Temperature Range | -10° to 40°C (14° to 104°F) |
| Temperature Accuracy | ±0.5°C (±1.8°F) |
| Tilted Element | No |
| Retrofits | Fits most 2" housings |
| Certifications | CE |
| Common Use | Cruising/Racing Sailboats, Leisure/Yachting, Fishing |
Frequently asked questions
What does the DST-820 measure?
It measures speed through water, depth, and water temperature. It also has an integrated attitude sensor that reports heel and trim.
Does it come with a cable?
Yes. The 6 m (20') NMEA 2000 cable is part of this package.
What network does it use?
It outputs NMEA 2000. The NMEA 2000 LEN is 2, so include it when you total up the power load on your network.
What size hole does it need?
The hole size is 51 mm (2"). The housing is a low profile thru-hull style and it's listed to fit most existing 2" housings.
What hull materials is it made for?
Fiberglass or metal hulls. The housing itself is plastic and the maximum deadrise angle is 22°.
How accurate is the speed reading?
The Gen2 paddlewheel gives precise start-up data below 0.3 knots, linear accuracy from 0.6 knots, and stable readings up to 45 knots. Speed output is 5.7 Hz.
How do I calibrate it?
You use the free CAST app over Bluetooth BLE. Scan the QR code, enter the one-time security password, and pick basic or advanced calibration. Advanced calibration allows manual speed entries for multiple heel angles and up to 10 speeds.
What's the depth range?
Depth is measured from 0.5 m (1.6') to 100 m (330'). The conventional beam is 10° x 44° and depth updates once per second.
What voltage does it need?
It runs on 9 to 16 VDC with an 80 W power rating.
Is the DST-820 a fish-finding transducer?
No. It's a multisensor for speed, depth and temperature data on your network. Sonar imaging is a different job.
How secure is the Bluetooth connection?
Setup uses a QR code and a one-time security password entered on your mobile device. The sensor is compliant with UK PSTI security standards.