{"product_id":"lumishore-eclipse-sl100-rgb-5m-marine-strip-light","title":"Lumishore Eclipse SL100 RGB 5m Strip Light 12V DC","description":"\u003cp class=\"nvn-hero\"\u003eThe Lumishore Eclipse SL100 is a 5-meter RGB accent strip that hides where the light comes from and shows only the glow. IP68, 60 LEDs per meter, and cut-to-length so it fits your exact run. Tuck it under a gunwale or behind a liner, dial in any color, and light up the boat without a single visible bulb.\u003c\/p\u003e\n\n\u003cdiv class=\"nvn-description\"\u003e\n\u003cp\u003eLumishore made its name on underwater lights, and the Eclipse SL100 brings that same marine-grade thinking topside. This is a 5-meter RGB strip built to hide in the places you'd never think to light. Tuck it under a gunwale, behind a ceiling liner, along the base of your seating, and the whole cockpit picks up a soft, even glow with no visible bulb and no hot spot. That's the whole idea here. You see the light, not the fixture. For a lot of boats it's the difference between a dark cockpit after sunset and a space that actually feels finished.\u003c\/p\u003e\n\u003cp\u003eThe strip runs 60 LEDs per meter, so the light lays down smooth instead of dotty. And because it's full RGB, you can dial in whatever color fits the moment. Cool white when you're cleaning up at the dock, a low red to save your night vision at the helm, a deep blue for a mellow evening on the hook. Set it once for the mood you like, or change it as the night goes on. It's fully encapsulated and potted, rated IP68, which is exactly what you want on a boat where spray and washdowns are just part of the deal.\u003c\/p\u003e\n\u003cp\u003eHere's what makes it friendly to install. The SL100 is cut-to-length, seal-ends, plug-and-play. You trim it at the marked cut points to match the exact run you've got, cap and seal the cut end against water, and wire it in. We've rigged these into gunwale channels and under helm dashes, and the flexible strip takes a gentle curve without fighting you. One honest tip from experience: the factory adhesive backing holds fine on clean, dry fiberglass, but if you're sticking it to a curved or damp surface, back it up with a bead of marine sealant or a few clips every several inches. Salt air and vibration will test cheap tape, so don't give it the chance.\u003c\/p\u003e\n\u003cp\u003eIt's a 12V DC system, happy anywhere in the 10 to 15 volt range, so it wires straight into your house bank through a switch or an existing lighting circuit. On a full 5-meter run you might notice the far end going a touch dimmer or shifting color slightly. That's normal voltage drop on any long LED run, nothing wrong with the strip. If you're chasing perfectly even color across the whole length, feed power from both ends or split the run into shorter zones. Seal those cut ends properly, mount the driver somewhere with a little airflow instead of buried in a sealed locker, and this strip will ride out season after season.\u003c\/p\u003e\n\u003cp\u003eBecause it's RGB, the Eclipse SL100 does a lot of jobs from one strip. Warm tones for a relaxed dinner at anchor. Bright white when you're rigging lines in the dark or scrubbing the deck. A calm blue or green trailing along the waterline that looks great from the dock. And on an overnight run, a low red setting keeps the cockpit usable without wrecking the helmsman's night vision. One strip, a dozen moods.\u003c\/p\u003e\n\u003cp\u003eThe SL100 really comes alive on Lumishore's Lumi-Link control, which lets you set colors and zones and even sync it with Lumishore EOS or SUPRA underwater lights for one coordinated show. Stick with the Lumishore controller for the RGB strip. Generic third-party dimmers can cause flicker or lockups, and that's a headache you don't need. So who's this for? Center consoles adding accent light to a T-top, cruisers dressing up a cabin, pontoon owners who want the deck to pop after sunset. It's decorative and courtesy lighting, not a spotlight or a floodlight, and that's exactly its job. Subtle, clean, and built to handle the water far better than the strip lights off a hardware-store shelf.\u003c\/p\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eKey Features\u003c\/h2\u003e\n\u003cul class=\"nvn-features\"\u003e\n  \u003cli\u003e60 LEDs per meter for smooth, even light with no visible dots or hot spots\u003c\/li\u003e\n  \u003cli\u003eFull RGB color mixing, so one strip covers white work light, red night-vision, and any accent color\u003c\/li\u003e\n  \u003cli\u003eIP68 rated, fully encapsulated and potted for spray, washdowns, and salt air\u003c\/li\u003e\n  \u003cli\u003e5 meter length, cut-to-length at marked points to fit your exact run\u003c\/li\u003e\n  \u003cli\u003ePlug-and-play wiring with sealable cut ends, no soldering for a basic install\u003c\/li\u003e\n  \u003cli\u003eRuns on 12V DC (10 to 15V range), wires straight into your boat's house circuit\u003c\/li\u003e\n  \u003cli\u003eFlexible strip bends into gunwale channels, under dashes, and behind liners\u003c\/li\u003e\n  \u003cli\u003ePairs with Lumishore Lumi-Link control for zones, color sync, and integration with Lumishore underwater lights\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"nvn-trust\"\u003e\n  \u003ch2\u003eWhy Buy from NVN Marine\u003c\/h2\u003e\n  \u003cul\u003e\n    \u003cli\u003eAuthorized Lumishore reseller, full manufacturer warranty\u003c\/li\u003e\n    \u003cli\u003eNMEA member and ABYC certified, advice from real boat techs\u003c\/li\u003e\n    \u003cli\u003eSame-day shipping before 3 PM ET on in-stock items\u003c\/li\u003e\n    \u003cli\u003eNY headquarters and Fort Lauderdale flagship retail store\u003c\/li\u003e\n  \u003c\/ul\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eFrequently Asked Questions\u003c\/h2\u003e\n\u003cdiv class=\"nvn-faq\"\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhat color options does the Eclipse SL100 give me?\u003c\/summary\u003e\n    \u003cp\u003eIt's full RGB, so you mix any color you want from one strip. Warm white for work light, red to protect night vision at the helm, blue or green for accent. You set the color through a Lumishore controller.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eCan I cut the strip to fit my boat?\u003c\/summary\u003e\n    \u003cp\u003eYes. The SL100 is cut-to-length at the marked cut points. Trim it to your run, seal the cut end properly against water, and wire it in. Only cut at the marked points so you don't kill a section.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eIs it really waterproof?\u003c\/summary\u003e\n    \u003cp\u003eIt carries an IP68 rating and the strip itself is fully encapsulated and potted. The one weak spot on any strip light is a cut end, so seal your cut ends with marine-grade sealant or heat-shrink and you're set.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhat voltage does it need?\u003c\/summary\u003e\n    \u003cp\u003eIt runs on 12V DC and is happy anywhere from about 10 to 15 volts, which is normal boat-battery territory. Wire it through a switch to your house bank or an existing lighting circuit.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhy does the far end look dimmer on a long run?\u003c\/summary\u003e\n    \u003cp\u003eThat's ordinary voltage drop on a 5-meter LED run, not a fault. If you want perfectly even color end to end, feed power from both ends of the strip or split the run into shorter zones.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eHow do I mount it so it stays put?\u003c\/summary\u003e\n    \u003cp\u003eThe strip has adhesive backing that holds well on clean, dry surfaces. On curved or damp spots, back it up with marine sealant or small mounting clips every few inches. Boat vibration and salt air are hard on tape alone.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhere do people install these?\u003c\/summary\u003e\n    \u003cp\u003eUnder gunwales, along seating bases, behind ceiling liners, under the helm dash, around T-tops and hardtops. Anywhere you want light without seeing the source. It's accent and courtesy lighting, not a spotlight.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eCan I sync it with my other Lumishore lights?\u003c\/summary\u003e\n    \u003cp\u003eYes. Run it on Lumishore's Lumi-Link control and you can coordinate the SL100 with Lumishore EOS or SUPRA underwater lights for one synchronized color show.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eShould I use a third-party dimmer or controller?\u003c\/summary\u003e\n    \u003cp\u003eStick with the Lumishore controller for the RGB SL100. Generic PWM dimmers can cause flicker or lockups. The matched controller keeps the colors clean and stable.\u003c\/p\u003e\n  \u003c\/details\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eTechnical Specifications\u003c\/h2\u003e\n\u003ctable class=\"nvn-specs\"\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n\u003cth\u003eTitle\u003c\/th\u003e\n\u003ctd\u003eLumishore Eclipse SL100 RGB 5m Strip Light 12\/24vDC\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eBrand\u003c\/th\u003e\n\u003ctd\u003eLumishore\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eManufacturer Part Number\u003c\/th\u003e\n\u003ctd\u003e010-04539-00\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eUPC\u003c\/th\u003e\n\u003ctd\u003e847772004283\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eSeries\u003c\/th\u003e\n\u003ctd\u003eEclipse SL100\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eColor\u003c\/th\u003e\n\u003ctd\u003eRGB (multicolor)\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e5m (cuttable)\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eLED Density\u003c\/th\u003e\n\u003ctd\u003e60 LEDs per meter\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eVoltage Range\u003c\/th\u003e\n\u003ctd\u003e12V DC (10-15V DC)\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eWaterproof Rating\u003c\/th\u003e\n\u003ctd\u003eIP68\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eConstruction\u003c\/th\u003e\n\u003ctd\u003eFully encapsulated and potted\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eInstallation\u003c\/th\u003e\n\u003ctd\u003eCut to length, seal ends, plug and play\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eControl\u003c\/th\u003e\n\u003ctd\u003eCompatible with Lumishore Lumi-Link\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eCategory\u003c\/th\u003e\n\u003ctd\u003eLighting\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003cscript type=\"application\/ld+json\"\u003e\n{\n    \"@context\": \"https:\/\/schema.org\",\n    \"@type\": \"FAQPage\",\n    \"mainEntity\": [\n        {\n            \"@type\": \"Question\",\n            \"name\": \"What color options does the Eclipse SL100 give me?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"It's full RGB, so you mix any color you want from one strip. Warm white for work light, red to protect night vision at the helm, blue or green for accent. You set the color through a Lumishore controller.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Can I cut the strip to fit my boat?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Yes. The SL100 is cut-to-length at the marked cut points. Trim it to your run, seal the cut end properly against water, and wire it in. Only cut at the marked points so you don't kill a section.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Is it really waterproof?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"It carries an IP68 rating and the strip itself is fully encapsulated and potted. The one weak spot on any strip light is a cut end, so seal your cut ends with marine-grade sealant or heat-shrink and you're set.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"What voltage does it need?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"It runs on 12V DC and is happy anywhere from about 10 to 15 volts, which is normal boat-battery territory. Wire it through a switch to your house bank or an existing lighting circuit.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Why does the far end look dimmer on a long run?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"That's ordinary voltage drop on a 5-meter LED run, not a fault. If you want perfectly even color end to end, feed power from both ends of the strip or split the run into shorter zones.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"How do I mount it so it stays put?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"The strip has adhesive backing that holds well on clean, dry surfaces. On curved or damp spots, back it up with marine sealant or small mounting clips every few inches. Boat vibration and salt air are hard on tape alone.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Where do people install these?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Under gunwales, along seating bases, behind ceiling liners, under the helm dash, around T-tops and hardtops. Anywhere you want light without seeing the source. It's accent and courtesy lighting, not a spotlight.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Can I sync it with my other Lumishore lights?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Yes. Run it on Lumishore's Lumi-Link control and you can coordinate the SL100 with Lumishore EOS or SUPRA underwater lights for one synchronized color show.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Should I use a third-party dimmer or controller?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Stick with the Lumishore controller for the RGB SL100. Generic PWM dimmers can cause flicker or lockups. The matched controller keeps the colors clean and stable.\"\n            }\n        }\n    ]\n}\n\u003c\/script\u003e\n","brand":"Lumishore","offers":[{"title":"Default Title","offer_id":44996544921693,"sku":"1004660","price":199.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0299\/7266\/0317\/files\/LMS0100453900_001.jpg?v=1788627658","url":"https:\/\/nvnmarine.com\/products\/lumishore-eclipse-sl100-rgb-5m-marine-strip-light","provider":"NVN Marine","version":"1.0","type":"link"}