Lewmar 393780200 Opening Portlight, Gray Lens, Silver Frame
Lewmar 393780200 Opening Portlight, Gray Lens, Silver Frame — Product description
The Lewmar 393780200 is an opening portlight with a silver aluminum frame, gray acrylic lens, flyscreen, and white ABS trim. It fits a 15-15/16 x 6-3/4 inch cut-out, so it's a straightforward swap when you're replacing a worn port and want fresh air below.
If you're replacing an old opening port on a cabin side or a hull, the Lewmar 393780200 is built around one number that matters more than any other: the cut-out. The hole in your boat needs to measure 15-15/16 inches wide by 6-3/4 inches tall. That's the opening this portlight is made for. Get that right and everything else follows.
It's a rectangular opening portlight with a silver aluminum frame and a gray acrylic lens. The frame measures 16-3/4 inches wide by 7-1/2 inches tall overall, and it stands 5/32 inch deep. A flyscreen is built in, so you can crack it open for air without inviting every bug on the dock inside. White ABS plastic trim finishes the cabin side, and a clip handle holds it shut. Twelve M5 x 25 screws come with it.
Who's it for? Boaters swapping out a tired, crazed, or leaking port on a cruiser, a trawler, or a sailboat with a sensible cabin side. It also suits anyone who wants more ventilation below on a hot summer weekend. The gray lens cuts glare and gives the cabin a bit of privacy, while still letting plenty of light through.
Take measurements before you order, and measure the cut-out, not the frame. The frame is larger than the hole and sits over the edges. If your old opening is bigger than 15-15/16 by 6-3/4 or isn't square, this frame won't cover it. If it's smaller, you'll be cutting. Radius the corners to match the spigot, because sharp square corners tend to crack gelcoat and leave a gap the sealant can't bridge.
Plan your bedding too. A cut-out that's been fastened before often has old holes that won't line up with the new ones. Fill and seal the unused holes so water doesn't find its way into the core. Use butyl tape or a marine sealant you can cut out later, not something that locks the frame in for good. You'll thank yourself when it's time to service the port years down the road.
About those screws. Twelve M5 x 25 fasteners are supplied, and 25 mm won't suit every cabin side. Thin laminate may call for a shorter length, and a thick core or an old backing ring may need longer ones. Dry-fit before you bed anything. Fender washers or a backing plate help spread the load on cored topsides.
Don't overtighten. The white ABS trim can crack if you crank the frame down to stop a leak, or if it spans an uneven liner. If it leaks, fix the bedding. Don't crush the trim to make up for it.
Care is simple. Fresh water and a mild boat soap keep the gray acrylic looking right. Skip acetone, MEK, and aggressive plastic cleaners, since acrylic crazes quickly. Rinse the aluminum frame after a trip in salt water and keep the bedding intact, because trapped salt water is what pits an aluminum flange over time.
One honest limit. This is a ventilation and light portlight. It isn't a substitute for a classified deadlight in a high-impact hull zone or below the waterline. Check your boat's design before you pick a location. Also note that the flyscreen and the handle hardware are the parts that wear first on any opening port, so it's worth knowing they're there to maintain.
We stock Lewmar portlights and hardware, so if you're matching other ports on the same boat, send us the old part numbers and we'll help you line up the sizes. The crew here has fitted plenty of these, and we'd rather talk you through a measurement than see you cut a hole twice.
Key Features
- 15-15/16 x 6-3/4 inch cut-out, so you can measure your existing opening and know right away if it fits.
- 16-3/4 x 7-1/2 inch overall frame, which covers the edges of the cut-out.
- Silver aluminum frame for a strong, low-profile look on the hull or cabin side.
- Gray acrylic lens cuts glare and adds a little privacy below.
- Built-in flyscreen lets you ventilate the cabin and keep bugs out.
- White ABS plastic trim finishes the inside of the cabin cleanly.
- Clip handle holds the port closed and opens it for airflow.
- Twelve M5 x 25 screws included for mounting.
Why Buy from NVN Marine
- Authorized Lewmar reseller, full manufacturer warranty
- NMEA member and ABYC certified, advice from real boat techs
- Same-day shipping before 3 PM ET on in-stock items
- NY headquarters and Fort Lauderdale flagship retail store
Technical specifications
| Title | Lewmar Opening Portlight, Gray Acrylic Lens, Silver Aluminum Frame, With Flyscreen |
|---|---|
| Brand | Lewmar |
| Manufacturer Part Number | 393780200 |
| UPC | 743683120336 |
| Product Type | Opening Portlight |
| Cut-Out Width | 15-15/16 Inch |
| Cut-Out Height | 6-3/4 Inch |
| Overall Width | 16-3/4 Inch |
| Overall Height | 7-1/2 Inch |
| Overall Depth | 5/32 Inch |
| Frame Material | Aluminum |
| Frame Finish | Silver |
| Lens Material | Acrylic |
| Lens Color | Gray |
| Flyscreen | Included |
| Inside Trim | White ABS Plastic |
| Handle | Clip Handle |
| Fasteners | Twelve M5 x 25 Screws |
Frequently asked questions
What cut-out size does the Lewmar 393780200 need?
The cut-out is 15-15/16 inches wide by 6-3/4 inches tall. The overall frame is 16-3/4 inches wide by 7-1/2 inches tall, so it sits over the edges of the hole.
What's the frame made of?
The frame is aluminum in a silver finish. The inside trim is white ABS plastic.
What color and material is the lens?
The lens is gray acrylic.
Does it have a flyscreen?
Yes. A flyscreen is part of the opening portlight, so you can ventilate the cabin and keep insects out.
What fasteners come with it?
Twelve M5 x 25 screws are listed with the portlight. Check the length against your cabin side thickness and dry-fit before bedding.
How does it latch shut?
It uses a clip handle.
Can I use it below the waterline?
We don't recommend it. It's an opening portlight for ventilation and light, not a classified deadlight, so check your boat's design and hull zone before choosing a location.
What should I use to bed it?
Butyl tape or a marine sealant you can cut out later works well. Avoid anything that permanently locks the frame in place, since you'll want to service the port eventually.
How do I clean the acrylic lens?
Use fresh water and a mild boat soap. Avoid acetone, MEK, and strong plastic cleaners, which can craze acrylic.