{"product_id":"jl-audio-xd-clraic2-25-2-channel-interconnect","title":"JL Audio XD-CLRAIC2-25 2-Channel Interconnect","description":"\u003cp class=\"nvn-hero\"\u003eThis is JL Audio's 2-channel twisted-pair interconnect, a 25-foot run of copper signal cable that carries a clean stereo signal from your source unit up to your amplifier. If your amp lives a long way from the helm, this is the cable that gets the signal there without dragging engine noise along with it.\u003c\/p\u003e\n\n\u003cdiv class=\"nvn-description\"\u003e\n\u003cp\u003eOn a boat, your amplifier almost never sits next to your source unit. The head unit's up at the helm, and the amp's tucked in a locker or under a seat somewhere aft. That's a long signal run, and every foot of it is a chance to pick up alternator whine, pump noise, and all the electrical hash a boat throws off. This JL Audio interconnect is built for exactly that kind of run. Twenty-five feet of it, so you can route it clean instead of stretching a shorter cable tight.\u003c\/p\u003e\n\u003cp\u003eThe twisted-pair core is the part that matters. The two conductors are twisted together down the whole length of the cable, and that geometry cancels out a lot of the noise a straight parallel cable would let through. Copper conductors carry the signal. It's a signal-level interconnect, the RCA-style cable that connects your source unit's preamp outputs to your amplifier's inputs. Two channels, so it handles a standard left and right stereo pair.\u003c\/p\u003e\n\u003cp\u003eWhere this earns its keep is the boats where the amp and the head unit are far apart. Center console with the stereo at the helm and the amp back by the batteries. Pontoon with a helm radio feeding speakers spread across the deck. Any rig where a short patch cable was never going to reach. Run this instead and you're not splicing extensions or leaving cable coiled up where it can pick up interference.\u003c\/p\u003e\n\u003cp\u003eKeep in mind this is the interconnect only. It carries signal, not power. You'll still need your power and ground wiring, speaker wire, and a remote turn-on lead to finish the amp install. And route it away from your power cables where you can. Even a good twisted-pair cable does better with a little separation from the high-current stuff.\u003c\/p\u003e\n\u003cp\u003eIt's a small part in the grand scheme of a stereo build, but the run between your source and your amp is exactly where a lot of noise problems start. Get that stretch right and the rest of the system tends to fall into place and sound the way it should.\u003c\/p\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eKey Features\u003c\/h2\u003e\n\u003cul class=\"nvn-features\"\u003e\n  \u003cli\u003e2-channel design carries a standard left and right stereo signal from source to amp\u003c\/li\u003e\n  \u003cli\u003eTwisted-pair core geometry rejects alternator whine and electrical noise on long runs\u003c\/li\u003e\n  \u003cli\u003eCopper conductors for clean, low-loss signal transfer\u003c\/li\u003e\n  \u003cli\u003e25-foot length reaches amplifiers mounted far from the helm without stretching a cable tight\u003c\/li\u003e\n  \u003cli\u003eSignal-level interconnect connects source unit preamp outputs to amplifier inputs\u003c\/li\u003e\n  \u003cli\u003eBuilt by JL Audio for real marine duty\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"nvn-trust\"\u003e\n  \u003ch2\u003eWhy Buy from NVN Marine\u003c\/h2\u003e\n  \u003cul\u003e\n    \u003cli\u003eAuthorized JL Audio reseller, full manufacturer warranty\u003c\/li\u003e\n    \u003cli\u003eNMEA member and ABYC certified, advice from real boat techs\u003c\/li\u003e\n    \u003cli\u003eSame-day shipping before 3 PM ET on in-stock items\u003c\/li\u003e\n    \u003cli\u003eNY headquarters and Fort Lauderdale flagship retail store\u003c\/li\u003e\n  \u003c\/ul\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eFrequently Asked Questions\u003c\/h2\u003e\n\u003cdiv class=\"nvn-faq\"\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhat does this cable actually do?\u003c\/summary\u003e\n    \u003cp\u003eIt's a signal interconnect. It carries the low-level stereo audio signal from your source unit's preamp outputs to your amplifier's inputs. It doesn't carry power or speaker-level output, just the clean signal the amp needs to work with.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eHow long is it?\u003c\/summary\u003e\n    \u003cp\u003e25 feet. That length is built for boats where the amplifier is mounted a good distance from the head unit, like a helm radio feeding an amp tucked back by the batteries.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhy twisted-pair instead of a regular cable?\u003c\/summary\u003e\n    \u003cp\u003eThe two conductors are twisted together along the whole length, and that cancels out a lot of the electrical noise a boat throws off. On a long run past pumps and an alternator, a straight cable is more likely to let that noise into your audio. Twisted-pair keeps it quieter.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eHow many channels does it carry?\u003c\/summary\u003e\n    \u003cp\u003eTwo. That's a standard left and right stereo pair, so one cable handles a full stereo feed to a two-channel amp or one pair of inputs on a larger amp.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eDoes it include power or speaker wire?\u003c\/summary\u003e\n    \u003cp\u003eNo. This is the signal interconnect only. You'll still need power and ground wiring, speaker wire, and a remote turn-on lead to complete the amplifier install.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eCan I run it right next to my power cables?\u003c\/summary\u003e\n    \u003cp\u003eBetter not to. Even a good twisted-pair interconnect does best with some separation from high-current power wiring. Route it down the opposite side of the boat where you can to keep the signal clean.\u003c\/p\u003e\n  \u003c\/details\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eTechnical Specifications\u003c\/h2\u003e\n\u003ctable class=\"nvn-specs\"\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n\u003cth\u003eTitle\u003c\/th\u003e\n\u003ctd\u003eJL Audio XD-CLRAIC2-25 2-Channel Twisted-Pair Audio Interconnect Cable, 25 Foot\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eBrand\u003c\/th\u003e\n\u003ctd\u003eJL Audio\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eManufacturer Part Number\u003c\/th\u003e\n\u003ctd\u003e010-13467-00\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eUPC\u003c\/th\u003e\n\u003ctd\u003e699440904278\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eModel Number\u003c\/th\u003e\n\u003ctd\u003eXD-CLRAIC2-25\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eCable Length\u003c\/th\u003e\n\u003ctd\u003e25 ft\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eChannels\u003c\/th\u003e\n\u003ctd\u003e2\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eConductor Material\u003c\/th\u003e\n\u003ctd\u003eCopper\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eCore Design\u003c\/th\u003e\n\u003ctd\u003eTwisted-pair\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eCable Type\u003c\/th\u003e\n\u003ctd\u003eAudio interconnect\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eConnector Type\u003c\/th\u003e\n\u003ctd\u003eRCA\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eSignal Level\u003c\/th\u003e\n\u003ctd\u003ePreamp \/ line level\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003cscript type=\"application\/ld+json\"\u003e\n{\n    \"@context\": \"https:\/\/schema.org\",\n    \"@type\": \"FAQPage\",\n    \"mainEntity\": [\n        {\n            \"@type\": \"Question\",\n            \"name\": \"What does this cable actually do?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"It's a signal interconnect. It carries the low-level stereo audio signal from your source unit's preamp outputs to your amplifier's inputs. It doesn't carry power or speaker-level output, just the clean signal the amp needs to work with.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"How long is it?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"25 feet. That length is built for boats where the amplifier is mounted a good distance from the head unit, like a helm radio feeding an amp tucked back by the batteries.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Why twisted-pair instead of a regular cable?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"The two conductors are twisted together along the whole length, and that cancels out a lot of the electrical noise a boat throws off. On a long run past pumps and an alternator, a straight cable is more likely to let that noise into your audio. Twisted-pair keeps it quieter.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"How many channels does it carry?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Two. That's a standard left and right stereo pair, so one cable handles a full stereo feed to a two-channel amp or one pair of inputs on a larger amp.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Does it include power or speaker wire?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"No. This is the signal interconnect only. You'll still need power and ground wiring, speaker wire, and a remote turn-on lead to complete the amplifier install.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Can I run it right next to my power cables?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Better not to. Even a good twisted-pair interconnect does best with some separation from high-current power wiring. Route it down the opposite side of the boat where you can to keep the signal clean.\"\n            }\n        }\n    ]\n}\n\u003c\/script\u003e\n","brand":"JL Audio","offers":[{"title":"Default Title","offer_id":45076273299549,"sku":"2009722","price":29.09,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0299\/7266\/0317\/files\/ImageServerAPI_46e51d22-923d-412c-853e-3802a16a86af.png?v=1789874993","url":"https:\/\/nvnmarine.com\/products\/jl-audio-xd-clraic2-25-2-channel-interconnect","provider":"NVN Marine","version":"1.0","type":"link"}