{"product_id":"hella-marine-led-light-bar-350-flood-light-958040521","title":"Hella Marine LED Light Bar 350 Wide Flood Light, 13.7 Inch","description":"\u003cp class=\"nvn-hero\"\u003eThe Hella Marine LED Light Bar 350 is a 13.7-inch surface-mount flood light built for real deck work. Twelve LEDs throw a wide beam with dual output, 1500 or 2200 lumens, so you can light the cockpit for line handling or crank it up for docking at night. Clear lens, black housing, brackets in the box.\u003c\/p\u003e\n\n\u003cdiv class=\"nvn-description\"\u003e\n\u003cp\u003eHella Marine builds lights you bolt on and forget about, and the LED Light Bar 350 fits that mold. This is a 13.7-inch surface-mount flood light with a twelve-LED array behind a clear lens, wrapped in a black housing that stays low-key on a hardtop or arch. It pulls 25 watts and throws a wide beam, so it's built to wash a whole area with light rather than punch a tight spot down the water. If you've ever tried to handle lines or work a transom in the dark with nothing but a headlamp, you already know why a proper deck flood earns its spot.\u003c\/p\u003e\n\u003cp\u003eThe part that makes this one handy is the dual output. You get 1500 lumens or 2200 lumens depending on how you wire it. Most folks run the two levels to a two-position switch at the helm. Low for close cockpit work where you don't want to blow out your night vision, high when you're backing into a slip or trying to find a cleat on a strange dock. It's a small thing, but on the water it matters. Bright isn't always better, and having a lower setting keeps the crew's eyes adjusted.\u003c\/p\u003e\n\u003cp\u003eInstall is straightforward. The brackets come in the box, and it's a true surface mount, so you're drilling a couple of holes and running a two-wire feed. At 25 watts you're only pulling around two amps, but don't skimp on the wire. Run 14-gauge minimum on a longer run so you don't lose brightness to voltage drop by the time the power reaches the light. If you're mounting to a thin fiberglass hardtop or a T-top panel, back it with a plate or big fender washers. Surface-mount brackets can flex and stress the gelcoat if there's nothing solid behind them.\u003c\/p\u003e\n\u003cp\u003eWhere does it go? Cockpit floods on an express cruiser, work lights under a hardtop, a pair on a radar arch aimed aft for backing down on fish, or a transom-mounted flood for cleaning up at the dock. The wide beam is the right call for all of that. You want coverage, not a spotlight. One tip from folks who run these on flybridge boats: angle the brackets down fifteen or twenty degrees so the beam hits the deck and not your own windshield. Glare bouncing back at the helm is the fastest way to hate an otherwise good light.\u003c\/p\u003e\n\u003cp\u003eBuild-wise, this is standard Hella Marine. Clear lens, sealed housing, corrosion-minded hardware. It's LED, so there's no filament to shake loose and no bulb to change. That said, do the install right. Put a little dielectric grease on the connections at the end caps before you button it up, especially if the light lives somewhere it catches spray. Salt air is patient, and a sealed connection now saves you a headache two seasons out. And keep it clear of exhaust risers and other heat sources. A black housing sitting in engine heat all day isn't doing itself any favors.\u003c\/p\u003e\n\u003cp\u003eA couple of practical notes before you buy. Think about how many you actually need. One 13.7-inch bar does a nice job over a single cockpit or a workstation, but a wide transom or a big open deck usually wants a pair to kill the shadows in the corners. And decide up front where the switch lives. Running the low and high outputs to a labeled two-position switch beats reaching for a breaker every time you want to change levels. It's the kind of thing that's easy to plan now and annoying to redo later. If you fish at night or run back to the ramp after dark, that little bit of forethought pays off every single trip.\u003c\/p\u003e\n\u003cp\u003eBottom line, it's a clean, honest deck flood from a brand that's been lighting boats for decades. Twelve LEDs, dual brightness, wide coverage, brackets included. If you need to light up a work area without a fussy install, this is an easy one to say yes to.\u003c\/p\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eKey Features\u003c\/h2\u003e\n\u003cul class=\"nvn-features\"\u003e\n  \u003cli\u003e13.7-inch surface-mount LED light bar with a twelve-LED array for wide-area deck coverage\u003c\/li\u003e\n  \u003cli\u003eDual light output, 1500 or 2200 lumens, wire to a two-position switch for low cockpit work or full docking brightness\u003c\/li\u003e\n  \u003cli\u003e25-watt draw, roughly 2 amps, easy on the electrical system for a light this bright\u003c\/li\u003e\n  \u003cli\u003eWide flood beam pattern washes the whole cockpit or work area instead of throwing a narrow spot\u003c\/li\u003e\n  \u003cli\u003eClear lens over a low-profile black housing that stays discreet on a hardtop or arch\u003c\/li\u003e\n  \u003cli\u003eMounting brackets included in the box for a straightforward surface-mount install\u003c\/li\u003e\n  \u003cli\u003eSolid-state LED construction, no bulbs to replace and no filament to vibrate loose\u003c\/li\u003e\n  \u003cli\u003eSealed marine-grade housing built for salt spray and UV exposure\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"nvn-trust\"\u003e\n  \u003ch2\u003eWhy Buy from NVN Marine\u003c\/h2\u003e\n  \u003cul\u003e\n    \u003cli\u003eAuthorized Hella Marine reseller, full manufacturer warranty\u003c\/li\u003e\n    \u003cli\u003eNMEA member and ABYC certified, advice from real boat techs\u003c\/li\u003e\n    \u003cli\u003eSame-day shipping before 3 PM ET on in-stock items\u003c\/li\u003e\n    \u003cli\u003eNY headquarters and Fort Lauderdale flagship retail store\u003c\/li\u003e\n  \u003c\/ul\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eFrequently Asked Questions\u003c\/h2\u003e\n\u003cdiv class=\"nvn-faq\"\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eHow bright is the LED Light Bar 350?\u003c\/summary\u003e\n    \u003cp\u003eIt's a dual-output light: 1500 lumens on the low setting and 2200 lumens on high. Wire the two levels to a two-position switch so you can run low for close cockpit work and high for docking.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eHow much power does it draw?\u003c\/summary\u003e\n    \u003cp\u003eIt's a 25-watt light, so you're pulling only about two amps. That's easy on the electrical system, but run 14-gauge wire minimum on a longer run so you don't lose brightness to voltage drop.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eDoes it come with mounting hardware?\u003c\/summary\u003e\n    \u003cp\u003eYes. The mounting brackets are included in the box. It's a surface mount, so you drill a couple of holes, fasten the brackets, and run a two-wire feed.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhat is the beam pattern?\u003c\/summary\u003e\n    \u003cp\u003eWide flood. It's built to wash a whole area with even light, like a cockpit or a work zone under a hardtop, rather than punch a tight spot at distance.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eHow long is the light?\u003c\/summary\u003e\n    \u003cp\u003e13.7 inches end to end, in a low-profile black housing that keeps a clean look on a hardtop, arch, or T-top.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eCan I run it at two different brightness levels?\u003c\/summary\u003e\n    \u003cp\u003eYes, that's the point of the dual 1500\/2200 lumen output. Most installers wire both levels to a two-position switch at the helm so the crew can pick low or high depending on the job.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eIs it built for saltwater?\u003c\/summary\u003e\n    \u003cp\u003eIt's a Hella Marine light, sealed and corrosion-minded. Do the install right, put dielectric grease on the connections at the end caps, and keep it clear of exhaust heat, and it'll hold up to salt air and spray.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhere should I mount it?\u003c\/summary\u003e\n    \u003cp\u003eCommon spots are cockpit floods on an express cruiser, work lights under a hardtop, a pair on a radar arch aimed aft, or a transom flood for the dock. On flybridge boats, angle the brackets down fifteen to twenty degrees so the beam doesn't glare back off your windshield.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eDoes it use replaceable bulbs?\u003c\/summary\u003e\n    \u003cp\u003eNo. It's a solid-state twelve-LED array, so there's no bulb to change and no filament to shake loose from vibration.\u003c\/p\u003e\n  \u003c\/details\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eTechnical Specifications\u003c\/h2\u003e\n\u003ctable class=\"nvn-specs\"\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n\u003cth\u003eTitle\u003c\/th\u003e\n\u003ctd\u003eHella Marine LED Light Bar 350 Wide Flood Light\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eBrand\u003c\/th\u003e\n\u003ctd\u003eHella Marine\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eManufacturer Part Number\u003c\/th\u003e\n\u003ctd\u003e958040521\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eUPC\u003c\/th\u003e\n\u003ctd\u003e760687161455\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eSeries\u003c\/th\u003e\n\u003ctd\u003eLED Light Bar 350\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eLamp Type\u003c\/th\u003e\n\u003ctd\u003eLED\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e13.7 inches\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eLED Count\u003c\/th\u003e\n\u003ctd\u003e12\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003ePower\u003c\/th\u003e\n\u003ctd\u003e25 Watts\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eLight Output\u003c\/th\u003e\n\u003ctd\u003e1500 \/ 2200 Lumens\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eBeam Pattern\u003c\/th\u003e\n\u003ctd\u003eWide Flood\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eLens\u003c\/th\u003e\n\u003ctd\u003eClear\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eHousing Color\u003c\/th\u003e\n\u003ctd\u003eBlack\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eMount Type\u003c\/th\u003e\n\u003ctd\u003eSurface Mount\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eMounting Brackets\u003c\/th\u003e\n\u003ctd\u003eIncluded\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003cscript type=\"application\/ld+json\"\u003e\n{\n    \"@context\": \"https:\/\/schema.org\",\n    \"@type\": \"FAQPage\",\n    \"mainEntity\": [\n        {\n            \"@type\": \"Question\",\n            \"name\": \"How bright is the LED Light Bar 350?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"It's a dual-output light: 1500 lumens on the low setting and 2200 lumens on high. Wire the two levels to a two-position switch so you can run low for close cockpit work and high for docking.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"How much power does it draw?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"It's a 25-watt light, so you're pulling only about two amps. That's easy on the electrical system, but run 14-gauge wire minimum on a longer run so you don't lose brightness to voltage drop.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Does it come with mounting hardware?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Yes. The mounting brackets are included in the box. It's a surface mount, so you drill a couple of holes, fasten the brackets, and run a two-wire feed.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"What is the beam pattern?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Wide flood. It's built to wash a whole area with even light, like a cockpit or a work zone under a hardtop, rather than punch a tight spot at distance.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"How long is the light?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"13.7 inches end to end, in a low-profile black housing that keeps a clean look on a hardtop, arch, or T-top.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Can I run it at two different brightness levels?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Yes, that's the point of the dual 1500\/2200 lumen output. Most installers wire both levels to a two-position switch at the helm so the crew can pick low or high depending on the job.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Is it built for saltwater?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"It's a Hella Marine light, sealed and corrosion-minded. Do the install right, put dielectric grease on the connections at the end caps, and keep it clear of exhaust heat, and it'll hold up to salt air and spray.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Where should I mount it?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Common spots are cockpit floods on an express cruiser, work lights under a hardtop, a pair on a radar arch aimed aft, or a transom flood for the dock. On flybridge boats, angle the brackets down fifteen to twenty degrees so the beam doesn't glare back off your windshield.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Does it use replaceable bulbs?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"No. It's a solid-state twelve-LED array, so there's no bulb to change and no filament to shake loose from vibration.\"\n            }\n        }\n    ]\n}\n\u003c\/script\u003e\n","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":44999401537629,"sku":"2007787","price":207.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0299\/7266\/0317\/files\/ImageServerAPI_e16b0140-0c90-4d24-99ab-bad4b53bbf2a.jpg?v=1788713610","url":"https:\/\/nvnmarine.com\/products\/hella-marine-led-light-bar-350-flood-light-958040521","provider":"NVN Marine","version":"1.0","type":"link"}