{"product_id":"hella-marine-black-series-3-2-led-cube-kit-flood","title":"Hella Marine Black Series 3.2\" LED Cube Kit, Flood Beam","description":"\u003cp class=\"nvn-hero\"\u003eHella Marine's Black Series 3.2 inch LED cube kit gives you two compact flood lights, a relay, a switch, and a sealed wiring harness in one box. 3000 lumens of wide, even white light for the cockpit or deck, multivolt for 12 or 24 volt systems, in a tough black housing built to Hella Marine's fit and forget standard.\u003c\/p\u003e\n\n\u003cdiv class=\"nvn-description\"\u003e\n\u003cp\u003eHella Marine built the Black Series 3.2 inch LED cube kit for boaters who need real, usable light on deck without hanging a big bar off the hardtop. You get two compact flood cubes, a relay, a switch, and a full wiring harness with a Deutsch DT connector in one box. Wire it in, aim it, and you've got a clean spread of white light across the cockpit or the swim platform.\u003c\/p\u003e\n\u003cp\u003eEach cube runs four LEDs behind a sealed lens and puts out a flood pattern rated at 3000 lumens for the pair. It's a true multivolt light. The kit draws 3.4 amps at 12 volts or 1.6 amps at 24 volts, so it drops onto either system without any extra hardware. That 40 watt draw is modest for the amount of light you get back, which matters when you're running lights off a house bank at anchor.\u003c\/p\u003e\n\u003cp\u003eFlood is the beam you want for work light. It throws wide and even instead of punching a tight spot out to the horizon. So it's the right call for lighting a cockpit while you're rigging lines, washing down a catch, or loading gear at a dark dock. We've rigged pairs like this as spreader lights under a T-top and as aft-facing deck floods on center consoles. Both work well. If you're after a long-throw beam to pick out a channel marker, that's a different job and a different light. This one is built to light up what's close, and it does that cleanly.\u003c\/p\u003e\n\u003cp\u003eMounting is a universal stud pattern, so each cube hangs off a single bolt through a half inch hole. On a solid aluminum T-top leg that's a five minute job. On thin console fiberglass, back it up with a proper backing plate or a fender washer so you don't crack the gelcoat when you snug it down. The housing is 2.7 inches deep, which clears the underside of most T-tops and hardtops, but measure your canvas zippers and clearances on a tight 25 to 28 foot center console before you commit to a spot.\u003c\/p\u003e\n\u003cp\u003eThe included relay and switch make the wiring straightforward, but treat the ground like it matters, because it does. Run a clean single-point ground and give the circuit its own fuse. At 3.4 amps a 10 amp fuse is the sensible size, and keeping these off a shared accessory circuit means they won't trip a breaker every time you flip them on with something else running. The DT connector on the harness is sealed and keeps corrosion out of the plug, which is exactly what you want on a boat.\u003c\/p\u003e\n\u003cp\u003eOne tip from experience: flood light this bright can bounce glare off bow rails and light-colored decks, so angle the cubes down about 15 degrees and you'll kill most of the reflection. The black housing looks sharp against a dark hardtop and disappears in daylight. It'll show salt streaks like anything else on a saltwater boat, so a quick freshwater rinse now and then keeps it looking right. For a small tender or a 20 foot skiff, 3000 lumens is a lot of light. It's really at home on bigger center consoles, cruisers, and sportfishers where you've got deck to cover.\u003c\/p\u003e\n\u003cp\u003eHella Marine makes this same 3.2 inch cube in a spot beam pattern if you need reach instead of spread. If your job is close-in deck and cockpit light, the flood kit you're looking at here is the one to grab. If you want both, a lot of boats run a flood pair for work light and a spot pair up high for distance, all off the same style of cube so the look stays consistent across the boat.\u003c\/p\u003e\n\u003cp\u003eBecause it's a Hella Marine light, it's built to the fit and forget standard the brand is known for. Sealed housing, marine-grade materials, and a lens that shrugs off UV and spray. These aren't a bargain-bin cube you'll be re-sealing next season. Buy the kit once, wire it in right, and it becomes one of those things on the boat you stop thinking about. That's the whole idea behind the Black Series line.\u003c\/p\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eKey Features\u003c\/h2\u003e\n\u003cul class=\"nvn-features\"\u003e\n  \u003cli\u003eFlood beam, 3000 lumens across the pair for wide, even deck and cockpit light\u003c\/li\u003e\n  \u003cli\u003e40 watt draw, 3.4 amps at 12 volts or 1.6 amps at 24 volts, true multivolt for either system\u003c\/li\u003e\n  \u003cli\u003eFour LEDs per cube behind a sealed lens for salt and UV resistance\u003c\/li\u003e\n  \u003cli\u003eCompact housing at 3.2 in wide by 3.3 in high by 2.7 in deep clears most T-tops and hardtops\u003c\/li\u003e\n  \u003cli\u003eUniversal single-stud mount installs off one half inch hole\u003c\/li\u003e\n  \u003cli\u003eComplete kit: two LED cubes, a relay, a switch, and a wiring harness with sealed Deutsch DT connector\u003c\/li\u003e\n  \u003cli\u003eBlack housing looks clean against dark hardtops and resists corrosion\u003c\/li\u003e\n  \u003cli\u003eFit and forget Hella Marine construction for long saltwater service\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"nvn-trust\"\u003e\n  \u003ch2\u003eWhy Buy from NVN Marine\u003c\/h2\u003e\n  \u003cul\u003e\n    \u003cli\u003eAuthorized Hella Marine reseller, full manufacturer warranty\u003c\/li\u003e\n    \u003cli\u003eNMEA member and ABYC certified, advice from real boat techs\u003c\/li\u003e\n    \u003cli\u003eSame-day shipping before 3 PM ET on in-stock items\u003c\/li\u003e\n    \u003cli\u003eNY headquarters and Fort Lauderdale flagship retail store\u003c\/li\u003e\n  \u003c\/ul\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eFrequently Asked Questions\u003c\/h2\u003e\n\u003cdiv class=\"nvn-faq\"\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eIs this a spot or a flood light?\u003c\/summary\u003e\n    \u003cp\u003eIt's a flood. The beam spreads wide and even, which is what you want for lighting up a cockpit, deck, or swim platform up close rather than throwing a tight beam out to the horizon.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eHow much light does the kit put out?\u003c\/summary\u003e\n    \u003cp\u003e3000 lumens for the pair, from a 40 watt draw. That's a lot of usable white work light for the power it pulls.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWill it run on a 24 volt system?\u003c\/summary\u003e\n    \u003cp\u003eYes. It's multivolt. The kit draws 3.4 amps at 12 volts or 1.6 amps at 24 volts, so it works on either system with no extra hardware.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhat comes in the box?\u003c\/summary\u003e\n    \u003cp\u003eTwo LED cube lights, a relay, a switch, and a wiring harness with a sealed Deutsch DT connector. It's a complete kit ready to wire in.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eHow does it mount?\u003c\/summary\u003e\n    \u003cp\u003eUniversal stud mount. Each cube hangs off a single bolt through a half inch hole. On thin console fiberglass, add a backing plate or fender washer so you don't crack the gelcoat.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhat size fuse should I use?\u003c\/summary\u003e\n    \u003cp\u003eAt 3.4 amps on 12 volts, a dedicated 10 amp fuse is the sensible size. Give the lights their own circuit rather than sharing with other accessories.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWill it fit under my T-top?\u003c\/summary\u003e\n    \u003cp\u003eThe housing is 2.7 inches deep, which clears the underside of most T-tops and hardtops. Measure canvas zippers and tight clearances on a 25 to 28 foot center console before you pick a spot.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eDoes it include wiring?\u003c\/summary\u003e\n    \u003cp\u003eYes. The relay, switch, and harness with the DT connector are all included. Run a clean single-point ground and its own fuse and the install is straightforward.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eIs it too bright for a small boat?\u003c\/summary\u003e\n    \u003cp\u003e3000 lumens is a lot of light for a small tender or a 20 foot skiff. It's really at home on bigger center consoles, cruisers, and sportfishers where you have more deck to cover.\u003c\/p\u003e\n  \u003c\/details\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eTechnical Specifications\u003c\/h2\u003e\n\u003ctable class=\"nvn-specs\"\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n\u003cth\u003eTitle\u003c\/th\u003e\n\u003ctd\u003eHella Marine Black Series 3.2 Inch LED Cube Kit, Flood Beam\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eBrand\u003c\/th\u003e\n\u003ctd\u003eHella Marine\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eManufacturer Part Number\u003c\/th\u003e\n\u003ctd\u003e358176811\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eUPC\u003c\/th\u003e\n\u003ctd\u003e4082300807660\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eBeam Pattern\u003c\/th\u003e\n\u003ctd\u003eFlood\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eLuminous Output\u003c\/th\u003e\n\u003ctd\u003e3000 Lumens\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eWattage\u003c\/th\u003e\n\u003ctd\u003e40 Watt\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eAmp Draw\u003c\/th\u003e\n\u003ctd\u003e3.4 A at 12 Volt \/ 1.6 A at 24 Volt\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eOperating Voltage\u003c\/th\u003e\n\u003ctd\u003e12 Volt \/ 24 Volt\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eLED Count\u003c\/th\u003e\n\u003ctd\u003e4 LEDs per cube\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eHousing Color\u003c\/th\u003e\n\u003ctd\u003eBlack\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eHousing Shape\u003c\/th\u003e\n\u003ctd\u003eRectangular\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eDimensions (W x H x D)\u003c\/th\u003e\n\u003ctd\u003e3.2 in x 3.3 in x 2.7 in\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eMount Type\u003c\/th\u003e\n\u003ctd\u003eUniversal Stud Mount\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eConnector\u003c\/th\u003e\n\u003ctd\u003eDeutsch DT\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eKit Contents\u003c\/th\u003e\n\u003ctd\u003e2 LED cubes, 1 relay, 1 switch, 1 wiring harness\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003cscript type=\"application\/ld+json\"\u003e\n{\n    \"@context\": \"https:\/\/schema.org\",\n    \"@type\": \"FAQPage\",\n    \"mainEntity\": [\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Is this a spot or a flood light?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"It's a flood. The beam spreads wide and even, which is what you want for lighting up a cockpit, deck, or swim platform up close rather than throwing a tight beam out to the horizon.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"How much light does the kit put out?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"3000 lumens for the pair, from a 40 watt draw. That's a lot of usable white work light for the power it pulls.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Will it run on a 24 volt system?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Yes. It's multivolt. The kit draws 3.4 amps at 12 volts or 1.6 amps at 24 volts, so it works on either system with no extra hardware.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"What comes in the box?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Two LED cube lights, a relay, a switch, and a wiring harness with a sealed Deutsch DT connector. It's a complete kit ready to wire in.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"How does it mount?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Universal stud mount. Each cube hangs off a single bolt through a half inch hole. On thin console fiberglass, add a backing plate or fender washer so you don't crack the gelcoat.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"What size fuse should I use?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"At 3.4 amps on 12 volts, a dedicated 10 amp fuse is the sensible size. Give the lights their own circuit rather than sharing with other accessories.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Will it fit under my T-top?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"The housing is 2.7 inches deep, which clears the underside of most T-tops and hardtops. Measure canvas zippers and tight clearances on a 25 to 28 foot center console before you pick a spot.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Does it include wiring?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Yes. The relay, switch, and harness with the DT connector are all included. Run a clean single-point ground and its own fuse and the install is straightforward.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Is it too bright for a small boat?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"3000 lumens is a lot of light for a small tender or a 20 foot skiff. It's really at home on bigger center consoles, cruisers, and sportfishers where you have more deck to cover.\"\n            }\n        }\n    ]\n}\n\u003c\/script\u003e\n","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":45052046966877,"sku":"2008168","price":133.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0299\/7266\/0317\/files\/ImageServerAPI_c100388b-26e6-476d-9776-711f60ad67a0.jpg?v=1789408604","url":"https:\/\/nvnmarine.com\/products\/hella-marine-black-series-3-2-led-cube-kit-flood","provider":"NVN Marine","version":"1.0","type":"link"}