{"product_id":"hella-marine-32-led-light-bar-9000lm-spot-beam","title":"Hella Marine Black Series 32-Inch LED Light Bar, 9000LM Spot","description":"\u003cp class=\"nvn-hero\"\u003eThe Hella Marine Black Series 32-inch LED light bar throws a tight spot beam and 9000 lumens off the bow, so you pick out channel markers, pots, and debris long before you're on top of them. Multivoltage 12V or 24V, sealed flush-mount housing, mounting hardware in the box, built to Hella Marine's fit-and-forget standard.\u003c\/p\u003e\n\n\u003cdiv class=\"nvn-description\"\u003e\n\u003cp\u003eHella Marine built the Black Series light bar for boaters who run before dawn or come home after dark. This is the 32-inch model, a slim spot-beam bar packing 33 clear LEDs and 9000 lumens of clean white output. Point it forward off a hardtop or T-top and it reaches way out there, which is exactly what you want when you're idling into an unlit channel or watching for a floating log at cruise.\u003c\/p\u003e\n\u003cp\u003eThe spot beam is the key spec here. It's a tight, focused pattern that throws light a long way down-range instead of spreading it wide and close. On the water that means you see the far marker, the anchored boat running no lights, the line of pots before you're in them. If you're after a close-in wash across the cockpit, this isn't that bar. This one's job is distance. A lot of guys run a spot bar up high for reach and a separate flood down low for the near field, and that combo is tough to beat.\u003c\/p\u003e\n\u003cp\u003eNow the power side, because it matters on this one. The bar draws 8.9 to 12.5 amps at 12 volts, or 4.2 to 6.1 amps at 24 volts, so it's happy on either system. That 12-amp draw at 12V is real, though. Run it on 10-gauge wire at a minimum, fuse it properly, and keep the run as short as you can so you don't dim the output on a long pull from the console. On a 24V boat the current drops by half and the wiring gets a lot easier. Either way, give it its own switch. At 9000 lumens it's far too bright to tie into your nav light circuit.\u003c\/p\u003e\n\u003cp\u003eThe 33-LED array runs off a wide-range driver, which is why you see that current range instead of a single number. It handles the voltage swings a boat's electrical system throws at it and holds output steady. Fuse each side on a 24V setup, and use marine-grade connectors at the pigtail. Heat and a bad crimp are what kill light bars early, not the LEDs themselves. Do the connections right the first time and it's a fit-and-forget piece.\u003c\/p\u003e\n\u003cp\u003eBuild quality is where Hella Marine earns its name. The housing is black, the lens is clear, and the whole unit is a sealed flush-mount design that sits clean against a hardtop or bar. Mounting hardware comes in the box. On a boat that pounds through chop, we'd back the mounting feet with a proper backing plate and through-bolt them rather than trusting self-tappers alone. Salt air and vibration are hard on anything mounted up high, and a bar this bright is worth mounting once and mounting right.\u003c\/p\u003e\n\u003cp\u003eOne more thing worth knowing. Nine thousand lumens is a lot of light, more than most boats have ever had up front. Kill it before you meet traffic in a channel so you're not blinding another skipper, and keep it off when you're running with your nav lights in a crowded harbor. It's a tool for reach and awareness in the dark, not something you leave burning the whole ride. Used that way, on the right stretch of open water, it changes how confident you feel picking your way home at night.\u003c\/p\u003e\n\u003cp\u003eSo who's it for? Center console owners running offshore before sunup, bay boat guys fishing the flats after dark, anyone with a hardtop or T-top who wants real reach out front. The 32-inch length fits most hardtops without hanging past the edges, and the flush mount keeps the profile low and clean. It's a premium bar at a premium output, built to the fit-and-forget standard Hella Marine is known for. Wire it right, mount it solid, and it'll hold its spot on the hardtop for years.\u003c\/p\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eKey Features\u003c\/h2\u003e\n\u003cul class=\"nvn-features\"\u003e\n  \u003cli\u003e9000 lumens of clean white LED output, bright enough to pick out markers and debris well down-range\u003c\/li\u003e\n  \u003cli\u003eSpot beam pattern for long-distance reach instead of a wide, close-in spread\u003c\/li\u003e\n  \u003cli\u003e33 clear LED array in a slim 32-inch bar that fits most hardtops and T-tops\u003c\/li\u003e\n  \u003cli\u003eMultivoltage design runs on 12V (8.9 to 12.5A) or 24V (4.2 to 6.1A) systems\u003c\/li\u003e\n  \u003cli\u003e165-watt total draw driven through a wide-range driver for stable output across voltage swings\u003c\/li\u003e\n  \u003cli\u003eSealed flush-mount housing in black with a clear lens, built for salt-air service\u003c\/li\u003e\n  \u003cli\u003eMounting hardware included in the box for a straightforward install\u003c\/li\u003e\n  \u003cli\u003eHella Marine fit-and-forget build standard for enduring reliability at sea\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"nvn-trust\"\u003e\n  \u003ch2\u003eWhy Buy from NVN Marine\u003c\/h2\u003e\n  \u003cul\u003e\n    \u003cli\u003eAuthorized Hella Marine reseller, full manufacturer warranty\u003c\/li\u003e\n    \u003cli\u003eNMEA member and ABYC certified, advice from real boat techs\u003c\/li\u003e\n    \u003cli\u003eSame-day shipping before 3 PM ET on in-stock items\u003c\/li\u003e\n    \u003cli\u003eNY headquarters and Fort Lauderdale flagship retail store\u003c\/li\u003e\n  \u003c\/ul\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eFrequently Asked Questions\u003c\/h2\u003e\n\u003cdiv class=\"nvn-faq\"\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhat kind of beam does this light bar throw?\u003c\/summary\u003e\n    \u003cp\u003eA spot beam. It's a tight, focused pattern that throws light a long way down-range for distance and reach, not a wide flood that washes the close-in area. If you want a near-field wash across the cockpit, pair it with a separate flood bar.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWill it run on my 12-volt boat?\u003c\/summary\u003e\n    \u003cp\u003eYes. It's multivoltage. On 12V it draws 8.9 to 12.5 amps, and on 24V it draws 4.2 to 6.1 amps, so it works on either system without a converter.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eHow bright is it?\u003c\/summary\u003e\n    \u003cp\u003e9000 lumens from a 33-LED clear array. That's a serious amount of light, more than most boats carry up front, so it reaches well out ahead of the bow.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhat size wire should I use?\u003c\/summary\u003e\n    \u003cp\u003eAt up to 12.5 amps on a 12V system, run 10-gauge wire at a minimum, fuse the circuit, and keep the run as short as you can so you don't lose output to voltage drop on a long pull from the console. On 24V the current is roughly half, so the wiring is easier.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eHow long is the bar?\u003c\/summary\u003e\n    \u003cp\u003e32 inches. It fits most hardtops and T-tops without hanging past the edges, and the flush mount keeps the profile low.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eDoes it come with mounting hardware?\u003c\/summary\u003e\n    \u003cp\u003eYes, mounting hardware is included in the box. On a boat that pounds through chop, we'd add a backing plate and through-bolt the feet rather than relying on self-tappers alone.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eCan I flush mount it on a hardtop?\u003c\/summary\u003e\n    \u003cp\u003eYes. It's a sealed flush-mount design that sits clean against a hardtop or bar with a low profile.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eIs it sealed for marine use?\u003c\/summary\u003e\n    \u003cp\u003eYes. The sealed housing and clear lens are built to Hella Marine's fit-and-forget standard for salt-air service. A fresh-water rinse now and then helps it last.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eShould I wire it into my nav lights?\u003c\/summary\u003e\n    \u003cp\u003eNo. Give it its own switch. At 9000 lumens it's far brighter than nav lighting and should run independently so you can kill it before meeting traffic in a channel.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eDo I need both a spot and a flood bar?\u003c\/summary\u003e\n    \u003cp\u003eNot required, but a lot of boaters run a spot bar up high for long-range reach and a separate flood down low for the near field. This bar covers the spot side of that setup.\u003c\/p\u003e\n  \u003c\/details\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eTechnical Specifications\u003c\/h2\u003e\n\u003ctable class=\"nvn-specs\"\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n\u003cth\u003eTitle\u003c\/th\u003e\n\u003ctd\u003eHella Marine Black Series 32-Inch LED Light Bar\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eBrand\u003c\/th\u003e\n\u003ctd\u003eHella Marine\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eManufacturer Part Number\u003c\/th\u003e\n\u003ctd\u003e358176311\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eUPC\u003c\/th\u003e\n\u003ctd\u003e760687179610\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eSeries\u003c\/th\u003e\n\u003ctd\u003eBlack Series\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003ctd\u003e32 Inches\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eLED Count\u003c\/th\u003e\n\u003ctd\u003e33 Clear Bulbs\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eLight Output\u003c\/th\u003e\n\u003ctd\u003e9000 Lumens\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eBeam Pattern\u003c\/th\u003e\n\u003ctd\u003eSpot Beam\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003ePower Draw\u003c\/th\u003e\n\u003ctd\u003e165 Watts\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eCurrent at 12 Volt\u003c\/th\u003e\n\u003ctd\u003e8.9 to 12.5 Amp\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eCurrent at 24 Volt\u003c\/th\u003e\n\u003ctd\u003e4.2 to 6.1 Amp\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eOperating Voltage\u003c\/th\u003e\n\u003ctd\u003e12V \/ 24V\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eLens\u003c\/th\u003e\n\u003ctd\u003eClear Lens\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eHousing Color\u003c\/th\u003e\n\u003ctd\u003eBlack\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eMounting\u003c\/th\u003e\n\u003ctd\u003eFlush Mount\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eIncluded Hardware\u003c\/th\u003e\n\u003ctd\u003eMounting hardware included\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003cscript type=\"application\/ld+json\"\u003e\n{\n    \"@context\": \"https:\/\/schema.org\",\n    \"@type\": \"FAQPage\",\n    \"mainEntity\": [\n        {\n            \"@type\": \"Question\",\n            \"name\": \"What kind of beam does this light bar throw?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"A spot beam. It's a tight, focused pattern that throws light a long way down-range for distance and reach, not a wide flood that washes the close-in area. If you want a near-field wash across the cockpit, pair it with a separate flood bar.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Will it run on my 12-volt boat?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Yes. It's multivoltage. On 12V it draws 8.9 to 12.5 amps, and on 24V it draws 4.2 to 6.1 amps, so it works on either system without a converter.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"How bright is it?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"9000 lumens from a 33-LED clear array. That's a serious amount of light, more than most boats carry up front, so it reaches well out ahead of the bow.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"What size wire should I use?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"At up to 12.5 amps on a 12V system, run 10-gauge wire at a minimum, fuse the circuit, and keep the run as short as you can so you don't lose output to voltage drop on a long pull from the console. On 24V the current is roughly half, so the wiring is easier.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"How long is the bar?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"32 inches. It fits most hardtops and T-tops without hanging past the edges, and the flush mount keeps the profile low.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Does it come with mounting hardware?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Yes, mounting hardware is included in the box. On a boat that pounds through chop, we'd add a backing plate and through-bolt the feet rather than relying on self-tappers alone.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Can I flush mount it on a hardtop?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Yes. It's a sealed flush-mount design that sits clean against a hardtop or bar with a low profile.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Is it sealed for marine use?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Yes. The sealed housing and clear lens are built to Hella Marine's fit-and-forget standard for salt-air service. A fresh-water rinse now and then helps it last.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Should I wire it into my nav lights?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"No. Give it its own switch. At 9000 lumens it's far brighter than nav lighting and should run independently so you can kill it before meeting traffic in a channel.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Do I need both a spot and a flood bar?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Not required, but a lot of boaters run a spot bar up high for long-range reach and a separate flood down low for the near field. This bar covers the spot side of that setup.\"\n            }\n        }\n    ]\n}\n\u003c\/script\u003e\n","brand":"Hella Marine","offers":[{"title":"Default Title","offer_id":44998822854749,"sku":"2007698","price":253.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0299\/7266\/0317\/files\/ImageServerAPI_9d5bca1b-291b-42f1-9be7-fa9370483070.jpg?v=1788687780","url":"https:\/\/nvnmarine.com\/products\/hella-marine-32-led-light-bar-9000lm-spot-beam","provider":"NVN Marine","version":"1.0","type":"link"}