{"product_id":"egis-4711-30-30a-push-button-circuit-breaker-spade","title":"Egis 4711-30 30A Push-Button Circuit Breaker | Spade","description":"\u003cp class=\"nvn-hero\"\u003eThe Egis Mobile Electric 4711-30 is a 30-amp push-to-reset circuit breaker that mounts through your panel and wires in with spade quick-connects. It protects a single DC circuit, resets with a button, and it's ignition protected for closed compartments. A clean, serviceable choice for any boat's accessory panel.\u003c\/p\u003e\n\n\u003cdiv class=\"nvn-description\"\u003e\n\u003cp\u003eThe Egis Mobile Electric 4711-30 is a 30-amp push-to-reset circuit breaker built to mount right through your panel or dash. It protects a single circuit, resets with the push of a button, and uses spade terminals so you can wire it in with standard female quick-connects instead of fighting ring lugs under a screw head. If you've ever had a fuse blow at the worst possible moment and realized you were fresh out of spares, you already know why a resettable breaker earns its spot on the boat. Wire it once, and you're done chasing fuses.\u003c\/p\u003e\n\u003cp\u003eThe spade terminals are the real story here. Each one takes a crimped female quick-connect, so you slide the wire on and move to the next circuit. No loose washers, no screwdriver dropped into the bilge, no stripped screw head two years from now. That makes this a clean choice when you're building out an accessory panel and want every circuit to look the same and come apart fast for service. The knurled nut and palnut hold it tight in the panel cutout, and the stainless steel hardware won't rust out on you a season or two down the road.\u003c\/p\u003e\n\u003cp\u003ePush-to-reset means the button pops out when the breaker trips. So you can see at a glance which circuit went down, then push it back in once you've cleared the fault. That beats crawling around under the helm with a test light hunting for a blown fuse. It's the kind of small thing you really appreciate at 5 AM when you're trying to get the livewell running before the bite turns on. One button, one circuit, no guesswork. And because it resets, you're not stuck dead in the water waiting on a spare you may not have.\u003c\/p\u003e\n\u003cp\u003eThe 50-volt DC rating covers everything you'll run on a standard boat. Twelve-volt, 24-volt, even a 32- or 42-volt house bank. At 30 amps this one sits in the middle of Egis's panel-mount range, which makes it a good fit for a bilge pump circuit, a livewell pump, a bank of cabin lights, a stereo amp, or the feed to a small accessory sub-panel. The rule of thumb is simple. Size the breaker to protect the wire, not the load, and you'll stay out of trouble.\u003c\/p\u003e\n\u003cp\u003eOn a 30-amp circuit we'd run 10-gauge wire as a practical minimum, and step up to 8-gauge on a long run where voltage drop starts to matter. Marine-grade tinned wire, always. The breaker's whole job is to open before that wire overheats, so matching the two is the point of the exercise. If you're not sure how long your run is, measure it and size up. Copper is cheap compared to a melted harness. And a breaker that nuisance-trips because the wire's undersized is just as annoying as no protection at all.\u003c\/p\u003e\n\u003cp\u003eIt's ignition protected, which means it's safe to install in a closed compartment where fuel or battery gases can collect. That's a real consideration if you're mounting near the engine or inside a battery box. One thing to know up front. The front of the breaker carries an IP40 rating and the back is IP00, so this is built for a dry panel location behind the dash, not out in the open weather. If you need to seal the button against spray, Egis offers a sealing boot separately. It doesn't come in the box, so add one to your order if your panel ever sees water.\u003c\/p\u003e\n\u003cp\u003eBottom line, the 4711-30 is a straightforward, serviceable breaker for anyone wiring a boat the right way. First-timer building a simple three-circuit panel or a rigger laying out a full accessory bus, it does the same honest job either way. And when something trips, you'll know exactly where to look. Keep a couple of spare quick-connects in your kit and this is a ten-minute install on most boats.\u003c\/p\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eKey Features\u003c\/h2\u003e\n\u003cul class=\"nvn-features\"\u003e\n  \u003cli\u003e30-amp rating protects a single DC circuit and trips before an overloaded wire can overheat\u003c\/li\u003e\n  \u003cli\u003ePush-to-reset button pops out on a trip so you can spot the faulted circuit and reset it by hand\u003c\/li\u003e\n  \u003cli\u003eSpade quick-connect terminals let you wire in with crimped female connectors, no ring lugs or loose screws\u003c\/li\u003e\n  \u003cli\u003e50-volt DC rating covers 12V, 24V, 32V and 42V systems\u003c\/li\u003e\n  \u003cli\u003eIgnition protected for safe mounting in closed compartments near fuel or battery gases\u003c\/li\u003e\n  \u003cli\u003eKnurled nut and palnut with stainless steel hardware for a tight, corrosion-resistant panel mount\u003c\/li\u003e\n  \u003cli\u003e14 to 140 degree Fahrenheit operating range handles a cold morning or a hot engine space\u003c\/li\u003e\n  \u003cli\u003eUL1500 listed with IP40 front and IP00 rear ratings for a dry behind-the-dash location\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"nvn-trust\"\u003e\n  \u003ch2\u003eWhy Buy from NVN Marine\u003c\/h2\u003e\n  \u003cul\u003e\n    \u003cli\u003eAuthorized Egis Mobile Electric reseller, full manufacturer warranty\u003c\/li\u003e\n    \u003cli\u003eNMEA member and ABYC certified, advice from real boat techs\u003c\/li\u003e\n    \u003cli\u003eSame-day shipping before 3 PM ET on in-stock items\u003c\/li\u003e\n    \u003cli\u003eNY headquarters and Fort Lauderdale flagship retail store\u003c\/li\u003e\n  \u003c\/ul\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eFrequently Asked Questions\u003c\/h2\u003e\n\u003cdiv class=\"nvn-faq\"\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhat amperage is the 4711-30?\u003c\/summary\u003e\n    \u003cp\u003eIt's a 30-amp breaker. The 4711 panel-mount line comes in several amp ratings, and this one protects a single circuit at 30 amps.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhat does push-to-reset mean?\u003c\/summary\u003e\n    \u003cp\u003eWhen the breaker trips on an overload, the button pops out. You see which circuit went down, clear the fault, and push the button back in to restore power. There's no fuse to replace.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhat are spade terminals and how do I connect to them?\u003c\/summary\u003e\n    \u003cp\u003eThey're flat quick-connect tabs. You crimp a matching female quick-connect onto your wire and slide it on. It's faster than ring lugs under a screw and comes apart cleanly for service.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWill this work on my 24-volt system?\u003c\/summary\u003e\n    \u003cp\u003eYes. It's rated to 50 volts DC, so it covers 12V, 24V, and even 32V or 42V banks.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhat size wire should I use with a 30-amp breaker?\u003c\/summary\u003e\n    \u003cp\u003eWe'd run 10-gauge marine-grade tinned wire as a practical minimum, and step up to 8-gauge on long runs where voltage drop matters. The breaker protects the wire, so size the wire to carry the load first.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eCan I mount this near the engine or in a battery box?\u003c\/summary\u003e\n    \u003cp\u003eYes. It's ignition protected, so it's safe in a closed compartment where fuel or battery gases can be present. Just keep it in a dry spot, since the housing isn't sealed against water.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eIs it waterproof?\u003c\/summary\u003e\n    \u003cp\u003eNo. The front is rated IP40 and the back is IP00, so it's made for a dry panel location behind the dash. If your panel sees spray, Egis offers a sealing boot that's sold separately.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eDoes a sealing boot come with it?\u003c\/summary\u003e\n    \u003cp\u003eNo. The boot is a separate accessory. If you want to seal the button against splash, add one to your order.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eIs this a single-pole breaker?\u003c\/summary\u003e\n    \u003cp\u003eYes. It protects one circuit. Use one breaker per circuit you want to protect.\u003c\/p\u003e\n  \u003c\/details\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eTechnical Specifications\u003c\/h2\u003e\n\u003ctable class=\"nvn-specs\"\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n\u003cth\u003eTitle\u003c\/th\u003e\n\u003ctd\u003eEgis Mobile Electric 4711-30 Push-Button Panel Mount Circuit Breaker\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eBrand\u003c\/th\u003e\n\u003ctd\u003eEgis Mobile Electric\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eManufacturer Part Number\u003c\/th\u003e\n\u003ctd\u003e4711-30\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eUPC\u003c\/th\u003e\n\u003ctd\u003e850053879302\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eAmperage\u003c\/th\u003e\n\u003ctd\u003e30 Amp\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eReset Type\u003c\/th\u003e\n\u003ctd\u003ePush-To-Reset\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eCircuit\u003c\/th\u003e\n\u003ctd\u003eSingle\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eVoltage Rating\u003c\/th\u003e\n\u003ctd\u003e50 Volt DC\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eTerminal Type\u003c\/th\u003e\n\u003ctd\u003eSpade (Quick-Connect)\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eOperating Temperature\u003c\/th\u003e\n\u003ctd\u003e14 to 140 degrees Fahrenheit\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eMounting\u003c\/th\u003e\n\u003ctd\u003ePanel Mount\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eHardware\u003c\/th\u003e\n\u003ctd\u003eKnurled Nut, Palnut, Stainless Steel\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eProtection Rating\u003c\/th\u003e\n\u003ctd\u003eUL1500 \/ IP40 \/ IP00\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eIgnition Protected\u003c\/th\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003cscript type=\"application\/ld+json\"\u003e\n{\n    \"@context\": \"https:\/\/schema.org\",\n    \"@type\": \"FAQPage\",\n    \"mainEntity\": [\n        {\n            \"@type\": \"Question\",\n            \"name\": \"What amperage is the 4711-30?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"It's a 30-amp breaker. The 4711 panel-mount line comes in several amp ratings, and this one protects a single circuit at 30 amps.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"What does push-to-reset mean?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"When the breaker trips on an overload, the button pops out. You see which circuit went down, clear the fault, and push the button back in to restore power. There's no fuse to replace.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"What are spade terminals and how do I connect to them?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"They're flat quick-connect tabs. You crimp a matching female quick-connect onto your wire and slide it on. It's faster than ring lugs under a screw and comes apart cleanly for service.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Will this work on my 24-volt system?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Yes. It's rated to 50 volts DC, so it covers 12V, 24V, and even 32V or 42V banks.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"What size wire should I use with a 30-amp breaker?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"We'd run 10-gauge marine-grade tinned wire as a practical minimum, and step up to 8-gauge on long runs where voltage drop matters. The breaker protects the wire, so size the wire to carry the load first.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Can I mount this near the engine or in a battery box?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Yes. It's ignition protected, so it's safe in a closed compartment where fuel or battery gases can be present. Just keep it in a dry spot, since the housing isn't sealed against water.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Is it waterproof?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"No. The front is rated IP40 and the back is IP00, so it's made for a dry panel location behind the dash. If your panel sees spray, Egis offers a sealing boot that's sold separately.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Does a sealing boot come with it?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"No. The boot is a separate accessory. If you want to seal the button against splash, add one to your order.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Is this a single-pole breaker?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Yes. It protects one circuit. Use one breaker per circuit you want to protect.\"\n            }\n        }\n    ]\n}\n\u003c\/script\u003e\n","brand":"Egis Mobile Electric","offers":[{"title":"Default Title","offer_id":67597777698909,"sku":"2010992","price":6.29,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0299\/7266\/0317\/files\/EME471120_001.jpg?v=1790923795","url":"https:\/\/nvnmarine.com\/products\/egis-4711-30-30a-push-button-circuit-breaker-spade","provider":"NVN Marine","version":"1.0","type":"link"}