{"product_id":"egis-4711-10-10a-push-button-breaker-spade-terminal","title":"Egis 4711-10 10A Push-Button Breaker | Spade Terminal","description":"\u003cp class=\"nvn-hero\"\u003eThe Egis Mobile Electric 4711-10 is a 10-amp push-to-reset circuit breaker for marine DC panels. It protects a single circuit up to 50 volts, and the spade quick-connect terminals make wiring fast. Ignition protected for closed compartments, with a knurled nut and palnut for a clean panel mount. Press the button to reset, no spare fuse needed.\u003c\/p\u003e\n\n\u003cdiv class=\"nvn-description\"\u003e\n\u003cp\u003eThe Egis Mobile Electric 4711-10 is a 10-amp push-to-reset circuit breaker built for the DC side of your boat. It guards a single circuit up to 50 volts, and when something pulls too much current, you reset it with a button instead of hunting for a spare fuse. What sets this one apart from the rest of the Egis panel-mount line is the terminals. This model runs spade quick-connect terminals, so wiring it up and servicing it later is fast.\u003c\/p\u003e\n\u003cp\u003eHere's why push-to-reset earns its place at the helm. A fuse is a one-shot deal. It blows, you're in the dark, and you'd better have the right amp rating sitting in your spares kit. A push-to-reset breaker trips, the button pops out so you can see exactly which circuit went down, and you bring it back with a press. That's it. No tools, no spares, no fumbling in a locker at night. On a crowded panel, that popped button is the fastest fault-finding tool you've got.\u003c\/p\u003e\n\u003cp\u003eThe spade terminals are the real story on this model. Instead of landing a ring under a screw, you crimp a female quick-connect onto your wire and slide it straight on. It makes the first install quicker, and it makes swapping or re-landing a wire down the road a two-second job. For a 10-amp circuit, run at least 16 AWG wire, and size up to 14 AWG on longer runs to keep voltage drop in check. ABYC wants the breaker close to the source of power it's protecting, so plan your panel layout with that in mind.\u003c\/p\u003e\n\u003cp\u003eThe 50-volt DC rating gives you plenty of headroom. It covers 12-volt systems, 24-volt systems, and the 32- and 42-volt setups you'll find on some larger boats and electric-drive rigs. A 10-amp breaker sits right in the pocket for a lot of common loads. Think cabin and courtesy lighting, a livewell pump, a stereo head unit, nav electronics, or a general accessory feed. Match the breaker to the wire and the load, not the other way around, and you're set.\u003c\/p\u003e\n\u003cp\u003eBecause it's ignition protected, you can mount the 4711-10 in a closed compartment where fuel or battery vapors might collect, like an engine space or a battery box. That's not something you can say about every breaker, and it matters when your panel lives below deck. The housing is UL1500 listed, with an IP40 rating on the front face and IP00 on the rear. In plain terms, the business side shrugs off dust and fingers, but the back terminals are open, so mount it behind a dry panel and keep spray off the connections. A sealing boot isn't included, so if your install sees any moisture at the back, plan to protect those terminals yourself.\u003c\/p\u003e\n\u003cp\u003eEgis builds this push-to-reset line in a range of amp ratings, so the 4711-10's 10-amp point is just one choice in a family that scales up and down. Pick the amperage to match the wire gauge and the steady load on that circuit, not the device's peak draw alone. If you're protecting a feed that pulls 7 or 8 amps steady, 10 amps gives you a sensible margin without nuisance trips. If your load runs closer to the 10-amp mark all day, step up to the next size so you're not resetting it every time a pump kicks on.\u003c\/p\u003e\n\u003cp\u003eMounting comes down to a clean single-hole job. Egis includes a knurled nut and a palnut, so you snug it into the panel cutout and lock it down without chasing extra parts. The stainless steel hardware holds up to salt air, and the breaker is rated to operate from 14 to 140 degrees Fahrenheit, which comfortably covers a cold spring launch through a hot August afternoon in the engine room. It's a small part. But it's the kind of small part that keeps the rest of your electrical system honest.\u003c\/p\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eKey Features\u003c\/h2\u003e\n\u003cul class=\"nvn-features\"\u003e\n  \u003cli\u003e10-amp push-to-reset breaker protects a single DC circuit and resets with a button instead of a spare fuse\u003c\/li\u003e\n  \u003cli\u003eSpade quick-connect terminals for fast crimp-and-slide wiring and easy service\u003c\/li\u003e\n  \u003cli\u003e50 volt DC rating covers 12V, 24V, 32V, and 42V systems\u003c\/li\u003e\n  \u003cli\u003eIgnition protected for safe mounting in closed compartments with fuel or battery vapors\u003c\/li\u003e\n  \u003cli\u003ePush-to-reset button pops out as a visible trip indicator for quick fault-finding\u003c\/li\u003e\n  \u003cli\u003eKnurled nut and palnut included for a clean single-hole panel mount\u003c\/li\u003e\n  \u003cli\u003eUL1500 listed with IP40 front and IP00 rear protection rating\u003c\/li\u003e\n  \u003cli\u003eStainless steel hardware and a 14 to 140 degree Fahrenheit operating range for marine conditions\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"nvn-trust\"\u003e\n  \u003ch2\u003eWhy Buy from NVN Marine\u003c\/h2\u003e\n  \u003cul\u003e\n    \u003cli\u003eAuthorized Egis Mobile Electric reseller, full manufacturer warranty\u003c\/li\u003e\n    \u003cli\u003eNMEA member and ABYC certified, advice from real boat techs\u003c\/li\u003e\n    \u003cli\u003eSame-day shipping before 3 PM ET on in-stock items\u003c\/li\u003e\n    \u003cli\u003eNY headquarters and Fort Lauderdale flagship retail store\u003c\/li\u003e\n  \u003c\/ul\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eFrequently Asked Questions\u003c\/h2\u003e\n\u003cdiv class=\"nvn-faq\"\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhat does the Egis 4711-10 protect?\u003c\/summary\u003e\n    \u003cp\u003eIt protects a single DC circuit up to 10 amps at 50 volts or less. When the circuit draws more than 10 amps, the breaker trips and cuts power until you reset it.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhat's the difference between spade and screw terminals?\u003c\/summary\u003e\n    \u003cp\u003eThe 4711-10 uses spade quick-connect terminals. You crimp a female quick-connect onto your wire and slide it on, instead of landing a ring terminal under a screw. It's faster to wire and faster to service later.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhat wire gauge should I use on a 10-amp circuit?\u003c\/summary\u003e\n    \u003cp\u003eRun at least 16 AWG for a 10-amp circuit, and step up to 14 AWG on longer runs to hold down voltage drop. Match the wire and breaker to the load on that circuit.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eCan I use it on a 24-volt system?\u003c\/summary\u003e\n    \u003cp\u003eYes. The 50 volt DC rating covers 12V, 24V, and 32 or 42 volt systems, so it works across the common marine DC voltages.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eIs the 4711-10 ignition protected?\u003c\/summary\u003e\n    \u003cp\u003eYes. It's ignition protected, so you can mount it in a closed compartment where fuel or battery vapors might be present, like an engine space or battery box.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eHow do I reset it after it trips?\u003c\/summary\u003e\n    \u003cp\u003eJust press the button. The button pops out when the breaker trips, which also tells you at a glance which circuit went down. Push it back in to restore power, no spare fuse required.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eHow does it mount?\u003c\/summary\u003e\n    \u003cp\u003eIt's a single-hole panel mount. Egis includes a knurled nut and a palnut, so you drop it into the panel cutout and lock it down without extra hardware.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eDoes it come with a sealing boot?\u003c\/summary\u003e\n    \u003cp\u003eNo. The front carries an IP40 rating but the rear terminals are IP00 and open, so mount it behind a dry panel. If the back of the breaker could see moisture, plan to protect the terminals yourself.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhat's the operating temperature range?\u003c\/summary\u003e\n    \u003cp\u003eIt's rated to operate from 14 to 140 degrees Fahrenheit, which covers cold-weather launches through hot engine-room conditions in summer.\u003c\/p\u003e\n  \u003c\/details\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eTechnical Specifications\u003c\/h2\u003e\n\u003ctable class=\"nvn-specs\"\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n\u003cth\u003eTitle\u003c\/th\u003e\n\u003ctd\u003eEgis 4711-10 10A Push-To-Reset Circuit Breaker, Spade Terminal\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eBrand\u003c\/th\u003e\n\u003ctd\u003eEgis Mobile Electric\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eManufacturer Part Number\u003c\/th\u003e\n\u003ctd\u003e4711-10\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eUPC\u003c\/th\u003e\n\u003ctd\u003e850053879265\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eAmperage\u003c\/th\u003e\n\u003ctd\u003e10 Amp\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eReset Type\u003c\/th\u003e\n\u003ctd\u003ePush-To-Reset\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eCircuit\u003c\/th\u003e\n\u003ctd\u003eSingle\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eVoltage\u003c\/th\u003e\n\u003ctd\u003e50 Volt DC\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eTerminal Type\u003c\/th\u003e\n\u003ctd\u003eSpade Terminal\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eMounting\u003c\/th\u003e\n\u003ctd\u003ePanel Mount\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eIgnition Protected\u003c\/th\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eIncluded Hardware\u003c\/th\u003e\n\u003ctd\u003eKnurled Nut, Palnut, Stainless Steel Hardware\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eOperating Temperature\u003c\/th\u003e\n\u003ctd\u003e14 to 140 degrees Fahrenheit\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eProtection Rating\u003c\/th\u003e\n\u003ctd\u003eUL1500 \/ IP40 \/ IP00\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003cscript type=\"application\/ld+json\"\u003e\n{\n    \"@context\": \"https:\/\/schema.org\",\n    \"@type\": \"FAQPage\",\n    \"mainEntity\": [\n        {\n            \"@type\": \"Question\",\n            \"name\": \"What does the Egis 4711-10 protect?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"It protects a single DC circuit up to 10 amps at 50 volts or less. When the circuit draws more than 10 amps, the breaker trips and cuts power until you reset it.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"What's the difference between spade and screw terminals?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"The 4711-10 uses spade quick-connect terminals. You crimp a female quick-connect onto your wire and slide it on, instead of landing a ring terminal under a screw. It's faster to wire and faster to service later.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"What wire gauge should I use on a 10-amp circuit?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Run at least 16 AWG for a 10-amp circuit, and step up to 14 AWG on longer runs to hold down voltage drop. Match the wire and breaker to the load on that circuit.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Can I use it on a 24-volt system?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Yes. The 50 volt DC rating covers 12V, 24V, and 32 or 42 volt systems, so it works across the common marine DC voltages.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Is the 4711-10 ignition protected?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Yes. It's ignition protected, so you can mount it in a closed compartment where fuel or battery vapors might be present, like an engine space or battery box.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"How do I reset it after it trips?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Just press the button. The button pops out when the breaker trips, which also tells you at a glance which circuit went down. Push it back in to restore power, no spare fuse required.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"How does it mount?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"It's a single-hole panel mount. Egis includes a knurled nut and a palnut, so you drop it into the panel cutout and lock it down without extra hardware.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Does it come with a sealing boot?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"No. The front carries an IP40 rating but the rear terminals are IP00 and open, so mount it behind a dry panel. If the back of the breaker could see moisture, plan to protect the terminals yourself.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"What's the operating temperature range?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"It's rated to operate from 14 to 140 degrees Fahrenheit, which covers cold-weather launches through hot engine-room conditions in summer.\"\n            }\n        }\n    ]\n}\n\u003c\/script\u003e\n","brand":"Egis Mobile Electric","offers":[{"title":"Default Title","offer_id":67597772226653,"sku":"2010991","price":6.29,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0299\/7266\/0317\/files\/EME471110_001.jpg?v=1790923394","url":"https:\/\/nvnmarine.com\/products\/egis-4711-10-10a-push-button-breaker-spade-terminal","provider":"NVN Marine","version":"1.0","type":"link"}