{"product_id":"dometic-9100-power-awning-hardware-reduced-pitch","title":"Dometic 9100 Power Awning Hardware, Reduced Pitch, Black, LED","description":"\u003cp class=\"nvn-hero\"\u003eThis is the genuine Dometic 9100 power awning hardware set, reduced pitch, in black, with the LED wire routed out the bottom. It's the electric arm assembly that drives a 9100 PowerChannel patio awning on a straight-side coach. If your old hardware is worn or you're rebuilding an awning, this is the full set that gets it opening and closing right again.\u003c\/p\u003e\n\n\u003cdiv class=\"nvn-description\"\u003e\n\u003cp\u003eThe Dometic 9100 has been the go-to power patio awning on a lot of travel trailers and fifth wheels for years, and this is the hardware that makes it move. Not the fabric. The hardware. You're looking at the full set of powered arms and mounting castings for a 9100 PowerChannel awning, built in the reduced-pitch configuration, finished in black, with the LED wiring set up to exit at the bottom. If you've ever had an awning arm seize up, strip out, or take a hit backing into a low branch, you know why you'd want the whole set rather than chasing one worn part at a time.\u003c\/p\u003e\n\u003cp\u003eSo what's reduced pitch? It's the arm geometry. Dometic builds the 9100 hardware in a few pitch styles so the awning sits at the right angle for how your coach is built. The reduced-pitch set holds the awning at a shallower slope, which is what you want on a lot of straight-side coaches where a steeper standard arm would ride too high or throw the fabric out at an awkward angle. If your rig came with reduced-pitch hardware from the factory, or your dealer spec'd it, this is the matching replacement. Match the pitch to what you're replacing and the awning opens, tensions, and closes the way it was designed to.\u003c\/p\u003e\n\u003cp\u003eThis set is made for coaches with straight sides, which covers most modern travel trailers and fifth wheels. It's a powered awning, so the arms carry the motor drive and you run the whole thing off a wall switch instead of cranking it by hand. Extend it at the campsite, pull it back in before you roll out, all from a button. The black finish is the darker trim look a lot of newer coaches ship with, so it blends in rather than standing out against the sidewall.\u003c\/p\u003e\n\u003cp\u003eThe LED wire exit at the bottom matters more than it sounds. A lot of 9100 awnings run an LED light strip along the roller, and that wiring has to get from the awning down into the coach without flapping loose or chafing. This hardware routes that LED wire out the bottom of the arm, which keeps it tucked and protected. If your existing awning has bottom-exit LED wiring, this set keeps the same routing so you're not re-drilling the sidewall or re-running harness.\u003c\/p\u003e\n\u003cp\u003eBecause it's a full set, you get the hardware for both sides, left and right, so you can rebuild the mount end to end. One thing to be clear on: this is the hardware, not the awning fabric. The fabric roll is a separate Dometic part sized to your coach's opening width. So if you're replacing torn fabric too, you'll want to order that alongside this. If your fabric is still good and it's the arms or the mounting that failed, this gets you back in business on its own.\u003c\/p\u003e\n\u003cp\u003eIs this a driveway job? It can be, if you're handy and you've got a helper and a solid ladder. Swapping power awning hardware means supporting the roller, disconnecting the LED and motor wiring, and getting the mounting brackets lined up and torqued on the sidewall. It's a two-person afternoon, not a five-minute swap. Take your time on the wiring connections and the pitch setting, because that's what decides whether the awning sheds water and rolls up clean. If you'd rather have a shop handle it, any RV service center that works on Dometic awnings will know this hardware.\u003c\/p\u003e\n\u003cp\u003eBottom line, if you've got a 9100 power awning on a straight-side coach and the hardware's shot, this is the genuine Dometic reduced-pitch set to bring it back. Order the fabric with it if yours is done, match the pitch to what you're replacing, and you'll have shade back over the campsite the way the factory intended.\u003c\/p\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eKey Features\u003c\/h2\u003e\n\u003cul class=\"nvn-features\"\u003e\n  \u003cli\u003eGenuine Dometic 9100 power awning hardware, full set for both sides so you can rebuild the mount end to end\u003c\/li\u003e\n  \u003cli\u003eReduced-pitch arm geometry holds the awning at a shallower slope suited to straight-side coaches\u003c\/li\u003e\n  \u003cli\u003eElectric powered operation, extend and retract from a wall switch with no hand cranking\u003c\/li\u003e\n  \u003cli\u003eBlack finish matches the darker trim on newer travel trailers and fifth wheels\u003c\/li\u003e\n  \u003cli\u003eLED wire exits at the bottom of the arm, keeping roller-light wiring tucked and protected\u003c\/li\u003e\n  \u003cli\u003eBuilt for coaches with straight sides, the most common modern trailer and fifth-wheel wall style\u003c\/li\u003e\n  \u003cli\u003eFits the Dometic 9100 PowerChannel power patio awning platform\u003c\/li\u003e\n  \u003cli\u003eHardware-only set, pair with a coach-width Dometic fabric roll for a full awning rebuild\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"nvn-trust\"\u003e\n  \u003ch2\u003eWhy Buy from NVN Marine\u003c\/h2\u003e\n  \u003cul\u003e\n    \u003cli\u003eAuthorized Dometic reseller, full manufacturer warranty\u003c\/li\u003e\n    \u003cli\u003eNMEA member and ABYC certified, advice from real boat techs\u003c\/li\u003e\n    \u003cli\u003eSame-day shipping before 3 PM ET on in-stock items\u003c\/li\u003e\n    \u003cli\u003eNY headquarters and Fort Lauderdale flagship retail store\u003c\/li\u003e\n  \u003c\/ul\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eFrequently Asked Questions\u003c\/h2\u003e\n\u003cdiv class=\"nvn-faq\"\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhat exactly comes in this Dometic 9100 hardware set?\u003c\/summary\u003e\n    \u003cp\u003eThis is the full powered hardware set for a Dometic 9100 patio awning, meaning the arm assemblies and mounting hardware for both sides. It's the reduced-pitch version in black with the LED wire routed out the bottom. It does not include the awning fabric, which is a separate Dometic part sized to your coach.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhat does reduced pitch mean?\u003c\/summary\u003e\n    \u003cp\u003ePitch is the angle the awning arms hold the fabric at. Dometic makes the 9100 hardware in different pitch styles so it fits how your coach is built. Reduced pitch sets the awning at a shallower slope, which suits a lot of straight-side coaches. Match the pitch to the hardware you're replacing.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWill this fit my awning?\u003c\/summary\u003e\n    \u003cp\u003eIt's built for the Dometic 9100 PowerChannel power patio awning on coaches with straight sides. If your rig runs a 9100 series power awning and came with reduced-pitch, bottom-exit LED hardware, this is the matching set. If you're not sure which pitch you have, check your existing hardware or your Dometic model number before ordering.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eIs the awning fabric included?\u003c\/summary\u003e\n    \u003cp\u003eNo. This is the hardware only. If your fabric is torn or faded, you'll want to order a Dometic fabric roll matched to your coach's opening width and run it at the same time. If the fabric's still good, this hardware gets you going on its own.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eIs this a powered awning or manual?\u003c\/summary\u003e\n    \u003cp\u003ePowered. The arms carry the electric drive, so you extend and retract from a wall switch instead of cranking it by hand.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhat's the LED wire exit at bottom about?\u003c\/summary\u003e\n    \u003cp\u003eMany 9100 awnings run an LED light strip on the roller. This hardware routes that LED wiring out the bottom of the arm so it stays tucked and protected. If your current awning uses bottom-exit LED wiring, this set keeps the same routing.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eCan I install this myself?\u003c\/summary\u003e\n    \u003cp\u003eIf you're handy, have a helper and a good ladder, yes. You'll support the roller, disconnect the motor and LED wiring, and mount and torque the brackets to the sidewall. Plan on a two-person afternoon. Any RV service center that works on Dometic awnings can also handle it.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eHow do I manually retract the awning if power fails?\u003c\/summary\u003e\n    \u003cp\u003eDometic's operating instructions for the 9100 series cover the manual override procedure. Because it varies by model, we'd point you to your model-specific Dometic manual rather than guess at the steps.\u003c\/p\u003e\n  \u003c\/details\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eTechnical Specifications\u003c\/h2\u003e\n\u003ctable class=\"nvn-specs\"\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n\u003cth\u003eTitle\u003c\/th\u003e\n\u003ctd\u003eDometic 9100 Power Awning Hardware, Reduced Pitch, Black, With Bottom LED Wire Exit, Full Set\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eBrand\u003c\/th\u003e\n\u003ctd\u003eDometic\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eManufacturer Part Number\u003c\/th\u003e\n\u003ctd\u003e8952003.400UL\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eUPC\u003c\/th\u003e\n\u003ctd\u003e0713814245665\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eAlternate Part Number\u003c\/th\u003e\n\u003ctd\u003e9108853274\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eAwning Series\u003c\/th\u003e\n\u003ctd\u003eDometic 9100 Power Patio Awning\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eComponent Type\u003c\/th\u003e\n\u003ctd\u003ePower Awning Hardware Set\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eConfiguration\u003c\/th\u003e\n\u003ctd\u003eFull Set (both sides)\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eDrive\u003c\/th\u003e\n\u003ctd\u003eElectric (Powered)\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003ePitch\u003c\/th\u003e\n\u003ctd\u003eReduced Pitch\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eColor\u003c\/th\u003e\n\u003ctd\u003eBlack\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eLED Wire Exit\u003c\/th\u003e\n\u003ctd\u003eBottom\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eCoach Fit\u003c\/th\u003e\n\u003ctd\u003eStraight Sides\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eApplication\u003c\/th\u003e\n\u003ctd\u003eRV \/ Coach\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003cscript type=\"application\/ld+json\"\u003e\n{\n    \"@context\": \"https:\/\/schema.org\",\n    \"@type\": \"FAQPage\",\n    \"mainEntity\": [\n        {\n            \"@type\": \"Question\",\n            \"name\": \"What exactly comes in this Dometic 9100 hardware set?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"This is the full powered hardware set for a Dometic 9100 patio awning, meaning the arm assemblies and mounting hardware for both sides. It's the reduced-pitch version in black with the LED wire routed out the bottom. It does not include the awning fabric, which is a separate Dometic part sized to your coach.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"What does reduced pitch mean?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Pitch is the angle the awning arms hold the fabric at. Dometic makes the 9100 hardware in different pitch styles so it fits how your coach is built. Reduced pitch sets the awning at a shallower slope, which suits a lot of straight-side coaches. Match the pitch to the hardware you're replacing.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Will this fit my awning?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"It's built for the Dometic 9100 PowerChannel power patio awning on coaches with straight sides. If your rig runs a 9100 series power awning and came with reduced-pitch, bottom-exit LED hardware, this is the matching set. If you're not sure which pitch you have, check your existing hardware or your Dometic model number before ordering.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Is the awning fabric included?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"No. This is the hardware only. If your fabric is torn or faded, you'll want to order a Dometic fabric roll matched to your coach's opening width and run it at the same time. If the fabric's still good, this hardware gets you going on its own.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Is this a powered awning or manual?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Powered. The arms carry the electric drive, so you extend and retract from a wall switch instead of cranking it by hand.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"What's the LED wire exit at bottom about?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Many 9100 awnings run an LED light strip on the roller. This hardware routes that LED wiring out the bottom of the arm so it stays tucked and protected. If your current awning uses bottom-exit LED wiring, this set keeps the same routing.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Can I install this myself?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"If you're handy, have a helper and a good ladder, yes. You'll support the roller, disconnect the motor and LED wiring, and mount and torque the brackets to the sidewall. Plan on a two-person afternoon. Any RV service center that works on Dometic awnings can also handle it.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"How do I manually retract the awning if power fails?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Dometic's operating instructions for the 9100 series cover the manual override procedure. Because it varies by model, we'd point you to your model-specific Dometic manual rather than guess at the steps.\"\n            }\n        }\n    ]\n}\n\u003c\/script\u003e\n","brand":"Dometic","offers":[{"title":"Default Title","offer_id":44788387577949,"sku":"2007323","price":640.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0299\/7266\/0317\/files\/ImageServerAPI_b2f028f8-8c71-4807-a20b-c262086ef5a5.png?v=1785012282","url":"https:\/\/nvnmarine.com\/products\/dometic-9100-power-awning-hardware-reduced-pitch","provider":"NVN Marine","version":"1.0","type":"link"}