{"product_id":"coleman-mach-9430-4572-non-ducted-ceiling-assembly","title":"Coleman Mach Non-Ducted Ceiling Assembly, Black, Wall Thermostat","description":"\u003cp class=\"nvn-hero\"\u003eThe Coleman Mach 9430-4572 is the non-ducted ceiling assembly for rooftop RV air conditioners, finished in black and built for wall-thermostat control. It's the interior trim panel that holds the return-air filter and directs cooled air into the cabin. No control knobs, no ductwork. The wall thermostat and control package are sold separately.\u003c\/p\u003e\n\n\u003cdiv class=\"nvn-description\"\u003e\n\u003cp\u003eThe Coleman Mach non-ducted ceiling assembly is the interior half of a rooftop RV air conditioner install. It's the part you actually see and touch inside the coach, the trim panel that seals against the ceiling, holds the return-air filter, and directs cooled air down into the living space. This one is the 9430-4572, finished in black, and it's built for setups that run off a wall thermostat instead of knobs on the ceiling.\u003c\/p\u003e\n\u003cp\u003eNon-ducted means the air conditioner sends its cold air straight into the room through this assembly, with no ductwork running through the roof. It's the common layout on single-zone rigs, smaller travel trailers, truck campers, and vans where one rooftop unit cools the whole cabin. Air gets pulled up through the return grille, passes the filter, runs across the evaporator, and comes back out the discharge louvers you can aim by hand. Simple, effective, and easy to service when you need to get at the filter.\u003c\/p\u003e\n\u003cp\u003eHere's the key detail on this version. It's set up for a wall thermostat, so there are no control knobs built into the ceiling. You run temperature and fan speed from a thermostat mounted on the wall, which a lot of owners prefer because you're not reaching up to the ceiling every time you want to bump the fan or drop the temp. The wall thermostat and control package aren't part of this assembly, so if you don't already have them wired in, you'll need to add them to finish the job.\u003c\/p\u003e\n\u003cp\u003eMost folks buying this are replacing a cracked, yellowed, or brittle assembly, or moving an older manual-knob setup over to thermostat control. UV and years of heat cycling are hard on these plastic panels. A fresh one tightens everything back up, kills the rattles, and gives you a clean return-air grille and filter pocket again. The black finish looks sharp against darker headliners and matches coaches that came with black interior trim from the factory.\u003c\/p\u003e\n\u003cp\u003eIt's designed for Coleman Mach non-ducted rooftop air conditioners. Before you order, it's worth pulling your existing assembly and checking your unit against the black wall-thermostat configuration. Coleman builds ducted and non-ducted assemblies, plus manual-knob and thermostat versions, and they aren't interchangeable. If your rig runs ductwork through the roof, you want a ducted assembly instead, not this one. And if your current assembly has knobs on it and you want to keep controlling the AC from the ceiling, that's a different part too.\u003c\/p\u003e\n\u003cp\u003eInstallation is straightforward for anyone comfortable working overhead. The assembly mounts up to the air conditioner's base pan from inside, sandwiching the ceiling between the rooftop unit and this interior trim. Kill power to the AC first, park on level ground, and grab a second set of hands. It helps to have someone holding the panel up while you start the fasteners. Snug the fasteners evenly so the assembly seals flat against the ceiling foam, then drop in the return filter and you're back in business. A clean seal keeps cold air from leaking up around the panel and helps the unit cool the way it should. Keep that filter clean through the season and this assembly will move air quietly for years.\u003c\/p\u003e\n\u003cp\u003eOne thing to be clear on. This is the interior ceiling assembly only. It doesn't include the rooftop air conditioner itself, and it doesn't include the wall thermostat or control package. If you're building or repairing a full system, order those pieces alongside it so you're not waiting on a second shipment mid-project. If you just need to refresh the interior trim on an existing non-ducted Coleman Mach setup that already runs on a wall thermostat, this is the right part, and it drops straight in.\u003c\/p\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eKey Features\u003c\/h2\u003e\n\u003cul class=\"nvn-features\"\u003e\n  \u003cli\u003eNon-ducted design sends cooled air straight into the cabin, so no roof ductwork is required\u003c\/li\u003e\n  \u003cli\u003eWall-thermostat ready with no ceiling knobs, so you set temperature and fan speed from the wall\u003c\/li\u003e\n  \u003cli\u003eBlack finish blends with darker headliners and factory black interior trim\u003c\/li\u003e\n  \u003cli\u003eBuilt for Coleman Mach non-ducted rooftop air conditioners\u003c\/li\u003e\n  \u003cli\u003eHolds the return-air filter and directs airflow through hand-aimable discharge louvers\u003c\/li\u003e\n  \u003cli\u003eInterior trim panel seals the ceiling opening between the rooftop unit and the cabin\u003c\/li\u003e\n  \u003cli\u003eDirect replacement for cracked, yellowed, or brittle non-ducted assemblies\u003c\/li\u003e\n  \u003cli\u003eManufacturer part number 9430-4572 from Coleman RVP\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"nvn-trust\"\u003e\n  \u003ch2\u003eWhy Buy from NVN Marine\u003c\/h2\u003e\n  \u003cul\u003e\n    \u003cli\u003eAuthorized Coleman reseller, full manufacturer warranty\u003c\/li\u003e\n    \u003cli\u003eNMEA member and ABYC certified, advice from real boat techs\u003c\/li\u003e\n    \u003cli\u003eSame-day shipping before 3 PM ET on in-stock items\u003c\/li\u003e\n    \u003cli\u003eNY headquarters and Fort Lauderdale flagship retail store\u003c\/li\u003e\n  \u003c\/ul\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eFrequently Asked Questions\u003c\/h2\u003e\n\u003cdiv class=\"nvn-faq\"\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eIs a wall thermostat included with this ceiling assembly?\u003c\/summary\u003e\n    \u003cp\u003eNo. This assembly is built to run off a wall thermostat, but the thermostat and control package are sold separately. If your rig doesn't already have them wired in, you'll need to add them to complete the installation.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhat does non-ducted mean?\u003c\/summary\u003e\n    \u003cp\u003eNon-ducted means the air conditioner discharges cold air directly into the room through this ceiling assembly, with no ductwork running through the roof. It's the typical single-zone layout on smaller trailers, truck campers, and vans where one rooftop unit cools the whole cabin.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eDoes this assembly have control knobs?\u003c\/summary\u003e\n    \u003cp\u003eNo. This is the wall-thermostat version, so there are no knobs on the ceiling. You control temperature and fan speed from a wall-mounted thermostat instead. If you want knobs on the ceiling, you'd need a manual-control assembly, which is a different part.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhat color is it?\u003c\/summary\u003e\n    \u003cp\u003eBlack. It's a clean match for darker headliners and coaches that came with black interior trim from the factory.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhich air conditioners does it fit?\u003c\/summary\u003e\n    \u003cp\u003eIt's designed for Coleman Mach non-ducted rooftop air conditioners. Before ordering, pull your existing assembly and confirm your unit is a non-ducted model set up for wall-thermostat control, since ducted and manual-knob versions aren't interchangeable.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhat exactly does a ceiling assembly do?\u003c\/summary\u003e\n    \u003cp\u003eIt's the interior trim panel between the rooftop AC and the cabin. It seals the ceiling opening, holds the return-air filter, pulls cabin air up across the evaporator, and directs the cooled air back out through discharge louvers you can aim by hand.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eDoes this include the air conditioner?\u003c\/summary\u003e\n    \u003cp\u003eNo. This is the interior ceiling assembly only. It doesn't include the rooftop air conditioner unit or the wall thermostat. If you're building a full system, order those pieces alongside it.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eCan I use this to replace an old cracked assembly?\u003c\/summary\u003e\n    \u003cp\u003eYes, that's the most common reason to buy one. If your existing non-ducted, wall-thermostat Coleman Mach assembly is cracked, yellowed, or rattling, this drops in as a direct replacement and freshens up the return grille and filter pocket.\u003c\/p\u003e\n  \u003c\/details\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eTechnical Specifications\u003c\/h2\u003e\n\u003ctable class=\"nvn-specs\"\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n\u003cth\u003eTitle\u003c\/th\u003e\n\u003ctd\u003eFor Coleman Mach Air Conditioner Non-Ducted Ceiling Assembly, Black, For Use With Wall Thermostat\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eBrand\u003c\/th\u003e\n\u003ctd\u003eColeman\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eManufacturer\u003c\/th\u003e\n\u003ctd\u003eColeman RVP\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eManufacturer Part Number\u003c\/th\u003e\n\u003ctd\u003e9430-4572\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eUPC\u003c\/th\u003e\n\u003ctd\u003e755790203192\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eComponent Type\u003c\/th\u003e\n\u003ctd\u003eCeiling Assembly\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eDuct Configuration\u003c\/th\u003e\n\u003ctd\u003eNon-Ducted\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eControl Type\u003c\/th\u003e\n\u003ctd\u003eWall Thermostat (sold separately)\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eColor\u003c\/th\u003e\n\u003ctd\u003eBlack\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eApplication\u003c\/th\u003e\n\u003ctd\u003eColeman Mach Rooftop RV Air Conditioner\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eKeystone Part Number\u003c\/th\u003e\n\u003ctd\u003e94304572\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eCompatibility\u003c\/th\u003e\n\u003ctd\u003eColeman Mach non-ducted air conditioners\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003cscript type=\"application\/ld+json\"\u003e\n{\n    \"@context\": \"https:\/\/schema.org\",\n    \"@type\": \"FAQPage\",\n    \"mainEntity\": [\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Is a wall thermostat included with this ceiling assembly?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"No. This assembly is built to run off a wall thermostat, but the thermostat and control package are sold separately. If your rig doesn't already have them wired in, you'll need to add them to complete the installation.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"What does non-ducted mean?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Non-ducted means the air conditioner discharges cold air directly into the room through this ceiling assembly, with no ductwork running through the roof. It's the typical single-zone layout on smaller trailers, truck campers, and vans where one rooftop unit cools the whole cabin.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Does this assembly have control knobs?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"No. This is the wall-thermostat version, so there are no knobs on the ceiling. You control temperature and fan speed from a wall-mounted thermostat instead. If you want knobs on the ceiling, you'd need a manual-control assembly, which is a different part.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"What color is it?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Black. It's a clean match for darker headliners and coaches that came with black interior trim from the factory.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Which air conditioners does it fit?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"It's designed for Coleman Mach non-ducted rooftop air conditioners. Before ordering, pull your existing assembly and confirm your unit is a non-ducted model set up for wall-thermostat control, since ducted and manual-knob versions aren't interchangeable.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"What exactly does a ceiling assembly do?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"It's the interior trim panel between the rooftop AC and the cabin. It seals the ceiling opening, holds the return-air filter, pulls cabin air up across the evaporator, and directs the cooled air back out through discharge louvers you can aim by hand.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Does this include the air conditioner?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"No. This is the interior ceiling assembly only. It doesn't include the rooftop air conditioner unit or the wall thermostat. If you're building a full system, order those pieces alongside it.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Can I use this to replace an old cracked assembly?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Yes, that's the most common reason to buy one. If your existing non-ducted, wall-thermostat Coleman Mach assembly is cracked, yellowed, or rattling, this drops in as a direct replacement and freshens up the return grille and filter pocket.\"\n            }\n        }\n    ]\n}\n\u003c\/script\u003e\n","brand":"Coleman","offers":[{"title":"Default Title","offer_id":45057361248349,"sku":"2008342","price":138.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0299\/7266\/0317\/files\/ImageServerAPI_d1c9f006-53af-48f4-bc45-f39b29ef1b1a.jpg?v=1789476063","url":"https:\/\/nvnmarine.com\/products\/coleman-mach-9430-4572-non-ducted-ceiling-assembly","provider":"NVN Marine","version":"1.0","type":"link"}