Carver Bimini Top Hold-Down Straps 60 in | 62060
Carver Bimini Top Hold-Down Straps 60 in | 62060 — Product description
If your bimini top has started flapping or you've lost a strap over the side, this is the fix. Genuine Carver replacement hold-down straps, 60 inches of black polypropylene webbing with a snap-hook on the end, four to a pack. Enough to re-do the front and rear tie-downs on both sides and keep your top locked down where it belongs.
Bimini top straps are the little parts that do a big job. They're what keep your top from flapping, lifting, or worse, letting go when you're running at speed. This is the genuine Carver replacement set: 60 inches long, an inch wide, four straps to a pack. If your old hold-downs are sun-rotted, frayed at the hook, or you've lost one over the side, this set gets you squared away before your next trip out.
Each strap is black polypropylene webbing with a single snap-hook on the end. Polypropylene is the right call for a boat. It shrugs off saltwater, doesn't soak up water and get heavy, and it stands up to UV better than a lot of the cheaper webbing you'll find. The 60-inch length gives you plenty of reach from the top's bows down to your deck fittings, and there's room to trim and re-sew if your boat runs shorter.
The snap-hook clips straight onto your existing deck eyes or pad eyes. No tools, no drilling. If you've already got the eye hardware mounted, this is a five-minute swap. Pull the old strap off, clip the new one on, tension it down, and you're done. Four straps handles a standard top with a hold-down front and rear on each side.
A couple of things worth knowing before you order. This is the hold-down webbing only, not a full bimini top and not the frame. It's the tie-down strap that anchors an already-mounted top to your deck. And it ends in a snap-hook, so if your top uses a different attachment, like a jaw slide or a sewn webbing loop, check your hardware and measure first.
Carver's been building boat covers and tops for over 30 years, and it's the small wear parts like these where that experience shows. Do yourself a favor and keep a spare set in the console. The day a strap lets go is never a convenient one.
Key Features
- 60-inch length by 1-inch width, enough reach to run from the bimini bows down to most deck fittings
- Black polypropylene webbing, resists saltwater and UV without soaking up water or getting heavy
- Single snap-hook end clips to existing deck eyes or pad eyes, no tools or drilling needed
- Set of four straps covers front and rear hold-downs on both sides of a standard top
- Genuine Carver replacement part, matched to Carver bimini tops
- Direct swap for worn, faded, or lost original hold-down straps
Why Buy from NVN Marine
- Authorized Carver by Covercraft reseller, full manufacturer warranty
- NMEA member and ABYC certified, advice from real boat techs
- Same-day shipping before 3 PM ET on in-stock items
- NY headquarters and Fort Lauderdale flagship retail store
Technical specifications
| Title | Replacement Hold-Down Strap For Bimini Top; 60 Inch Length x 1 Inch Width; Black; Polypropylene; With Single Snap-Hook; Set Of 4 |
|---|---|
| Brand | Carver by Covercraft |
| Manufacturer Part Number | 62060 |
| UPC | 813095022525 |
| Length | 60 inches |
| Width | 1 inch |
| Color | Black |
| Material | Polypropylene |
| Hardware | Single Snap-Hook |
| Quantity | Set of 4 |
| Application | Bimini top hold-down / tie-down |
Frequently asked questions
What's in the set?
Four black polypropylene hold-down straps, each 60 inches long by 1 inch wide, each with a single snap-hook. That's enough for front and rear hold-downs on both sides of a standard top.
Will these fit my bimini top?
They're genuine Carver replacement hold-down straps and clip to standard deck eyes with the snap-hook. If your top uses a different attachment, like a jaw slide or a sewn loop, check your hardware before ordering.
Do I need tools to install them?
No. The snap-hook clips onto your existing deck eye or pad eye. Pull the old strap off, clip the new one on, and tension it down.
What are the straps made of?
Polypropylene webbing. It resists saltwater and UV and doesn't absorb water, so it won't get heavy or mildew the way some webbing does.
Is this a complete bimini top?
No. This is the hold-down strap set only, the webbing that anchors an already-mounted top to the deck. It isn't the top or the frame.
Are they long enough for my boat?
At 60 inches each they reach from the bimini bows to most deck fittings. If your boat runs shorter, you can trim and re-sew the strap to length.
