{"product_id":"camco-40155-14x14-white-rv-roof-vent-lid-nvn-marine","title":"Camco 40155 14x14 White RV Roof Vent Lid | NVN Marine","description":"\u003cp class=\"nvn-hero\"\u003eThe Camco 40155 is a white, impact-resistant replacement lid for 14 inch by 14 inch RV roof vents. It's built for Ventline vents made before 2008 and Elixir vents from 1994 on. Molded polypropylene, pre-assembled, and packed with rust-resistant mounting hardware, so a cracked or sun-brittled lid is a quick afternoon fix that keeps your roof sealed.\u003c\/p\u003e\n\n\u003cdiv class=\"nvn-description\"\u003e\n\u003cp\u003eIf the vent lid over your galley or bathroom has gone chalky, cracked, or blown off down the highway, this is the fix. The Camco 40155 is a white replacement roof vent lid for standard 14 inch by 14 inch RV roof vents. It's the exact lid, not the whole vent assembly, so you're replacing just the part that took the beating from the sun.\u003c\/p\u003e\n\u003cp\u003eFitment matters here, so read this before you buy. This lid is made for Ventline vents built prior to 2008 and Elixir vents built from 1994 on. Those two share the same lid pattern and hinge layout. If your rig rolled out of the factory in that window, odds are good this is your lid. Not sure which brand you've got? Climb up on the roof and look at the old lid or the hinge base for a molded name. Measure the opening too. It should be a nominal 14 by 14, which is the most common RV vent size out there. Both the pre-2008 Ventline and the 1994-and-up Elixir use the same footprint, so if you can confirm either one you're set.\u003c\/p\u003e\n\u003cp\u003eVent lids live a hard life. They sit flat on the roof, baking in UV all summer, and polypropylene eventually goes brittle and chalky. One good hailstorm or a low branch at the campground, and a tired lid cracks or shatters. Sometimes they just let go at 65 on the interstate. When that happens you've got an open hole over your galley or bath, and the next rain finds it fast. Swapping the lid is a cheap afternoon job that keeps the water out.\u003c\/p\u003e\n\u003cp\u003eMany rigs carry two or three of these 14 by 14 vents. One over the galley, one in the bath, sometimes one in a bedroom. If one lid has gone brittle, the others aren't far behind, because they all caught the same sun. A lot of owners grab a couple at once and swap them all the same day. Saves a second trip up the ladder.\u003c\/p\u003e\n\u003cp\u003eThe 40155 is molded from impact-resistant polypropylene, so it shrugs off hail and the odd branch better than a sun-baked old lid. It's white, which reflects heat and matches most factory roof vents. Camco ships it pre-assembled with the hinge arms already attached, so there's no fiddly build up on the roof.\u003c\/p\u003e\n\u003cp\u003eEvery lid comes with its own mounting hardware, and it's rust-resistant, so it won't streak your roof or seize up in a year. Install is straightforward. Take out the hinge pins or screws holding the old lid, set the new one in the same spots, and drive the included hardware. Most folks are done in fifteen or twenty minutes with a screwdriver. Here's a quick tip. Before you toss the old lid, note how the hinge arms clip in. Some sit on pins, some screw down. The new 40155 uses the same style, so matching what came off makes the swap foolproof.\u003c\/p\u003e\n\u003cp\u003eOne more thing while you're up there. It's worth a look at your roof sealant around the vent flange whenever you pull a lid. If the butyl or lap sealant is cracked, hit it while the ladder's out. A fresh lid over a leaky flange still lets water sneak in, so a five-minute sealant check saves you a bigger repair later.\u003c\/p\u003e\n\u003cp\u003eKeep in mind this is the lid only. It's not the full vent, not the fan, not the interior garnish or screen. If your vent frame or fan motor is shot, you'll want the complete unit instead. But if the base and hinge are fine and it's just the cover that failed, this is all you need. The packaging is bilingual, English and French, so it's the same lid sold across the US and Canada.\u003c\/p\u003e\n\u003cp\u003eFor a common repair on a common vent, this is the honest fix. Match it to a Ventline pre-2008 or an Elixir 1994-and-up vent, measure your 14 by 14 opening, and you're back to a sealed roof for the price of a couple tanks of gas.\u003c\/p\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eKey Features\u003c\/h2\u003e\n\u003cul class=\"nvn-features\"\u003e\n  \u003cli\u003eWhite polypropylene construction reflects heat and matches most factory roof vents\u003c\/li\u003e\n  \u003cli\u003eImpact-resistant molding shrugs off hail and stray branches better than a sun-brittled lid\u003c\/li\u003e\n  \u003cli\u003eFits standard 14 inch by 14 inch RV roof vents\u003c\/li\u003e\n  \u003cli\u003eDesigned for Ventline vents built prior to 2008 and Elixir vents built from 1994 on\u003c\/li\u003e\n  \u003cli\u003eShips pre-assembled with the hinge arms already attached, no build required on the roof\u003c\/li\u003e\n  \u003cli\u003eIncludes all mounting hardware, and it's rust-resistant so it won't streak or seize\u003c\/li\u003e\n  \u003cli\u003eDirect replacement for a cracked, chalky, or missing vent lid\u003c\/li\u003e\n  \u003cli\u003eBilingual English and French packaging\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"nvn-trust\"\u003e\n  \u003ch2\u003eWhy Buy from NVN Marine\u003c\/h2\u003e\n  \u003cul\u003e\n    \u003cli\u003eAuthorized Camco reseller, full manufacturer warranty\u003c\/li\u003e\n    \u003cli\u003eNMEA member and ABYC certified, advice from real boat techs\u003c\/li\u003e\n    \u003cli\u003eSame-day shipping before 3 PM ET on in-stock items\u003c\/li\u003e\n    \u003cli\u003eNY headquarters and Fort Lauderdale flagship retail store\u003c\/li\u003e\n  \u003c\/ul\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eFrequently Asked Questions\u003c\/h2\u003e\n\u003cdiv class=\"nvn-faq\"\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhich vents does the Camco 40155 fit?\u003c\/summary\u003e\n    \u003cp\u003eIt's made for standard 14 inch by 14 inch RV roof vents, specifically Ventline vents built before 2008 and Elixir vents built from 1994 on. Measure your opening and confirm the brand before ordering.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eHow do I tell if I have a Ventline or Elixir vent?\u003c\/summary\u003e\n    \u003cp\u003eGet up on the roof and look at the old lid or the hinge base for a molded brand name. Both the pre-2008 Ventline and the 1994-and-up Elixir share this lid's pattern, so either one is a match.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhat color is this lid?\u003c\/summary\u003e\n    \u003cp\u003eWhite. It reflects heat and matches most factory roof vents. There's a smoke-tinted version in the family if you want the darker look, but this one is the white lid.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eDoes it come with mounting hardware?\u003c\/summary\u003e\n    \u003cp\u003eYes. Every lid ships with its own rust-resistant mounting hardware and comes pre-assembled with the hinge arms attached, so it's ready to install.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eIs this the whole vent or just the lid?\u003c\/summary\u003e\n    \u003cp\u003eJust the lid, the outer cover that hinges open. It doesn't include the vent frame, the fan, or the interior garnish or screen. If those are damaged you'll want the complete vent instead.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhat's it made of?\u003c\/summary\u003e\n    \u003cp\u003eImpact-resistant polypropylene. That's the same tough plastic the factory uses, and it holds up to hail and stray branches better than a sun-brittled old lid.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eHow long does it take to install?\u003c\/summary\u003e\n    \u003cp\u003eMost owners have it done in fifteen or twenty minutes with a screwdriver. Remove the old lid's hinge pins or screws, set the new one in the same spots, and drive the included hardware.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWill this fit a 14x14 vent from another vent maker?\u003c\/summary\u003e\n    \u003cp\u003eThis lid is engineered for the Ventline pre-2008 and Elixir 1994-up hinge pattern. If your vent isn't one of those, measure the opening and check the hinge layout first, since 14x14 lids aren't all interchangeable.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhy do RV vent lids need replacing?\u003c\/summary\u003e\n    \u003cp\u003eSun does them in. Years of UV make polypropylene brittle and chalky, and then hail, a branch, or highway wind cracks or tears off the lid. Replacing it keeps rain out of the coach.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eShould I reseal anything while I'm replacing the lid?\u003c\/summary\u003e\n    \u003cp\u003eIt's smart to check the roof sealant around the vent flange while you're up there. If the sealant is cracked, refresh it. A new lid over a leaky flange still lets water in.\u003c\/p\u003e\n  \u003c\/details\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eTechnical Specifications\u003c\/h2\u003e\n\u003ctable class=\"nvn-specs\"\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n\u003cth\u003eTitle\u003c\/th\u003e\n\u003ctd\u003eCamco 40155 RV Roof Vent Lid, 14 in x 14 in, White\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eBrand\u003c\/th\u003e\n\u003ctd\u003eCamco\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eManufacturer Part Number\u003c\/th\u003e\n\u003ctd\u003e40155\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eUPC\u003c\/th\u003e\n\u003ctd\u003e014717401555\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eColor\u003c\/th\u003e\n\u003ctd\u003eWhite\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eMaterial\u003c\/th\u003e\n\u003ctd\u003ePolypropylene\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eFits Vent Size\u003c\/th\u003e\n\u003ctd\u003e14 in x 14 in\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eCompatibility\u003c\/th\u003e\n\u003ctd\u003eVentline (prior to 2008), Elixir (1994 and on)\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eImpact Resistance\u003c\/th\u003e\n\u003ctd\u003eImpact-resistant\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eMounting Hardware\u003c\/th\u003e\n\u003ctd\u003eIncluded, rust-resistant\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eAssembly\u003c\/th\u003e\n\u003ctd\u003ePre-assembled\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003ePackaging Language\u003c\/th\u003e\n\u003ctd\u003eEnglish \/ French\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003cscript type=\"application\/ld+json\"\u003e\n{\n    \"@context\": \"https:\/\/schema.org\",\n    \"@type\": \"FAQPage\",\n    \"mainEntity\": [\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Which vents does the Camco 40155 fit?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"It's made for standard 14 inch by 14 inch RV roof vents, specifically Ventline vents built before 2008 and Elixir vents built from 1994 on. Measure your opening and confirm the brand before ordering.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"How do I tell if I have a Ventline or Elixir vent?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Get up on the roof and look at the old lid or the hinge base for a molded brand name. Both the pre-2008 Ventline and the 1994-and-up Elixir share this lid's pattern, so either one is a match.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"What color is this lid?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"White. It reflects heat and matches most factory roof vents. There's a smoke-tinted version in the family if you want the darker look, but this one is the white lid.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Does it come with mounting hardware?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Yes. Every lid ships with its own rust-resistant mounting hardware and comes pre-assembled with the hinge arms attached, so it's ready to install.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Is this the whole vent or just the lid?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Just the lid, the outer cover that hinges open. It doesn't include the vent frame, the fan, or the interior garnish or screen. If those are damaged you'll want the complete vent instead.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"What's it made of?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Impact-resistant polypropylene. That's the same tough plastic the factory uses, and it holds up to hail and stray branches better than a sun-brittled old lid.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"How long does it take to install?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Most owners have it done in fifteen or twenty minutes with a screwdriver. Remove the old lid's hinge pins or screws, set the new one in the same spots, and drive the included hardware.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Will this fit a 14x14 vent from another vent maker?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"This lid is engineered for the Ventline pre-2008 and Elixir 1994-up hinge pattern. If your vent isn't one of those, measure the opening and check the hinge layout first, since 14x14 lids aren't all interchangeable.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Why do RV vent lids need replacing?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Sun does them in. Years of UV make polypropylene brittle and chalky, and then hail, a branch, or highway wind cracks or tears off the lid. Replacing it keeps rain out of the coach.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Should I reseal anything while I'm replacing the lid?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"It's smart to check the roof sealant around the vent flange while you're up there. If the sealant is cracked, refresh it. A new lid over a leaky flange still lets water in.\"\n            }\n        }\n    ]\n}\n\u003c\/script\u003e\n","brand":"Camco","offers":[{"title":"Default Title","offer_id":45081195446365,"sku":"2010137","price":19.09,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0299\/7266\/0317\/files\/ImageServerAPI_75e76dbb-460b-4ab1-bd63-91fb5f1d194f.jpg?v=1790004918","url":"https:\/\/nvnmarine.com\/products\/camco-40155-14x14-white-rv-roof-vent-lid-nvn-marine","provider":"NVN Marine","version":"1.0","type":"link"}