Bulldog 6811S00 6-Inch Plastic Jack Wheel Service Kit
Bulldog 6811S00 6-Inch Plastic Jack Wheel Service Kit — Product description
When the wheel on your Bulldog trailer jack cracks or flat-spots, you don't need a whole new jack. This service kit gives you a fresh 6-inch plastic wheel built to fit Bulldog marine and recreational jacks, so you can get back to rolling your trailer around the yard or up the ramp. Quick swap, and you're done.
Anyone who's rolled a loaded boat trailer around a gravel lot knows the jack wheel takes a beating. It's the part that meets the ground, carries the tongue weight, and grinds over ramps, curbs, and stones every time you move the trailer. Eventually it cracks, flat-spots, or just wears down. When that happens, this Bulldog service kit lets you replace the wheel instead of the whole jack.
It's a 6-inch plastic wheel built to fit Bulldog marine and recreational trailer jacks. Plastic holds up well to the wet, salty conditions around a boat ramp, where a bare steel wheel would rust and seize. It won't leave marks on a clean garage floor either. If you launch and retrieve in salt water, that corrosion resistance is worth a lot over the life of the jack.
Bulldog builds jacks for towing and trailering that get used hard, and they're the choice of military and manufacturers for a reason. But the wheel is a wear item. It's meant to be serviced. Swapping in a fresh one restores smooth rolling so you're not fighting a wheel that won't turn while you're trying to line up the hitch by yourself.
The swap is straightforward. Pull the old wheel off the jack's caster fork, drop the new one in, and reinstall the axle bolt. Most folks have it done in a few minutes with basic hand tools. No need to remove the jack from the trailer. If your current wheel is chewed up or has gone flat, this gets you back to easy maneuvering in no time.
Good fit for boat trailers, utility trailers, and any recreational setup running a Bulldog jack with a 6-inch wheel. Check your existing wheel diameter before ordering so you match the size. If yours measures 6 inches, this is the replacement you want.
Key Features
- 6-inch plastic wheel, the correct replacement size for compatible Bulldog trailer jacks
- Plastic construction shrugs off rust and corrosion in wet, salty boat-ramp conditions
- Bulldog service part that swaps the wheel instead of replacing the entire jack
- Rolls smooth again so you can maneuver a loaded trailer by hand
- Fits Bulldog marine and recreational jacks that use a 6-inch wheel
- Installs in minutes with basic hand tools, no need to pull the jack off the trailer
Why Buy from NVN Marine
- Authorized Bulldog reseller, full manufacturer warranty
- NMEA member and ABYC certified, advice from real boat techs
- Same-day shipping before 3 PM ET on in-stock items
- NY headquarters and Fort Lauderdale flagship retail store
Technical specifications
| Title | Bulldog Trailer Jack Service Kit, 6-Inch Plastic Wheel |
|---|---|
| Brand | Bulldog |
| Manufacturer Part Number | 6811S00 |
| UPC | 088154093512 |
| Wheel Diameter | 6 inches |
| Wheel Material | Plastic |
| Fits | Marine and Recreational Jacks |
| Kit Type | Service / Replacement Kit |
Frequently asked questions
What size wheel is in this kit?
It's a 6-inch diameter plastic wheel. Measure your current jack wheel before ordering so you match the size.
Will this fit my Bulldog jack?
It's made for Bulldog marine and recreational trailer jacks that use a 6-inch wheel. Check that your jack takes a 6-inch wheel and you're set.
Why plastic instead of steel?
Plastic won't rust or corrode, which matters a lot if you launch in salt water or leave the trailer outside. It also won't mark up a clean floor.
Is this just the wheel or a whole new jack?
It's a service kit to replace the wheel on a jack you already own. You keep the jack and swap in the fresh wheel.
Is it hard to install?
Not at all. Pull the old wheel off the caster fork, drop the new one in, and reinstall the axle bolt. A few minutes with basic hand tools and you're done.
Can I use this on a boat trailer?
Yes. It fits Bulldog marine jacks, and the plastic wheel is a good match for the wet conditions around a boat ramp.
