{"product_id":"bps-marine-bps-6-ultrasonic-antifouling-system","title":"BPS Marine BPS-6 6-Transducer Ultrasonic Antifouling System 12VDC","description":"\u003cp class=\"nvn-hero\"\u003eThe BPS Marine BPS-6 is a six-transducer ultrasonic antifouling system for hulls up to 65 feet. The transducers epoxy to the inside of the hull surface, so there are no thru-hulls to cut. It runs off your house battery and covers hull, drives, and rudders from one control module.\u003c\/p\u003e\n\n\u003cdiv class=\"nvn-description\"\u003e\n\u003cp\u003eGrowth on the bottom of a boat is a slow tax. It adds drag, costs you fuel and top speed, and sends you back to the yard or the diver more often than you'd like. The BPS Marine BPS-6 goes after that problem with sound instead of paint. Six ultrasonic transducers send high-frequency waves through the hull, aimed at keeping growth from getting a grip in the first place.\u003c\/p\u003e\n\u003cp\u003eThis is the larger of the single-controller systems. One BPS-6 is rated for hulls up to 65 feet. If you've got a bigger boat, BPS Marine says you can add more systems to cover the extra length. And if you run a boat under 52 feet with pods or stern drives, this one system is meant to cover the whole boat, drives included.\u003c\/p\u003e\n\u003cp\u003eThat drive coverage is where ultrasonics earn their keep. Stern drives, rudders, stabilizers, and sea strainers are awkward places to paint and even worse places to scrub. Ultrasonic waves travel through complex parts that a brush can't reach, which is why a lot of owners with outdrives look at this kind of system.\u003c\/p\u003e\n\u003cp\u003eInstallation doesn't involve cutting anything. The transducers mount directly to your hull surface with the epoxy that's in the box. Each transducer comes with 15 feet of attached signal cable, and three extra 15 foot extension cables are included so you can reach the controller from the far corners of the boat. The control module has an integrated power cable and connects with a simple two-wire hookup to your battery bank or distribution panel. It runs on 12 or 24 volts DC and the average power draw is 1.5Ah, so plan for it on a boat that sits on the hook or on the dock for long stretches.\u003c\/p\u003e\n\u003cp\u003eEach transducer is rated at 60 watts. Instead of sitting on one frequency, the system sweeps a multi-frequency range from 20kHz to 42kHz. The idea behind the sweep is to cover a wider range of growth than a single tone would. BPS Marine says the frequencies used are outside the hearing range of humans and marine mammals, and the system is chemical-free, so nothing leaches into the water. That matters in marinas with strict rules on bottom paint.\u003c\/p\u003e\n\u003cp\u003eHere's what we'd tell you straight. Placement and bond quality matter. The transducers need to sit where the manual says, with a solid epoxy bond to the hull, so take your time on the install and follow the printed manual that comes in the kit. Don't expect miracles from a sloppy mounting job. And keep the system powered whenever the boat is sitting in the water, because that's when growth is trying to settle.\u003c\/p\u003e\n\u003cp\u003eWhat do you get out of it? A cleaner bottom means less drag, which helps fuel economy and top speed. It can also stretch the life of your bottom paint and cut down on how often you pay for hull cleaning. After it's installed, BPS Marine says there's no scheduled maintenance. It's a fit and forget system.\u003c\/p\u003e\n\u003cp\u003eThink about where you'll mount the transducers before you open the epoxy. Spread them out along the hull as the manual describes, and plan the cable runs so the control module ends up somewhere dry and easy to reach. With 15 feet of cable on each transducer and three extension cables on top of that, most boats have plenty of reach. Run the two power wires to a clean, properly fused feed and you're set. It's a weekend project for most owners, and it's far less messy than a haul-out and a fresh coat of paint.\u003c\/p\u003e\n\u003cp\u003eThis BPS-6 listing is the 12VDC version, and the full package is the control module, six transducers, three extension cables, two epoxy kits, and the printed manual. Not sure whether you need one system or two for your boat? Send the crew your hull length and drive setup and we'll help you sort it out before you order.\u003c\/p\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eKey Features\u003c\/h2\u003e\n\u003cul class=\"nvn-features\"\u003e\n  \u003cli\u003eSix 60W ultrasonic transducers cover hulls up to 65ft from a single control module\u003c\/li\u003e\n  \u003cli\u003eMulti-frequency sweep from 20kHz to 42kHz instead of a single fixed tone\u003c\/li\u003e\n  \u003cli\u003eNo thru-hulls, because the transducers epoxy to the hull surface\u003c\/li\u003e\n  \u003cli\u003e15ft of signal cable on every transducer, plus three 15ft extension cables for longer runs\u003c\/li\u003e\n  \u003cli\u003eRuns on 12V or 24V DC with an average draw of 1.5Ah\u003c\/li\u003e\n  \u003cli\u003eSimple two-wire hookup to your battery bank or distribution panel\u003c\/li\u003e\n  \u003cli\u003eCovers drives, rudders, stabilizers, and strainers that are hard to paint or scrub\u003c\/li\u003e\n  \u003cli\u003eChemical-free design that doesn't leach anything into the water\u003c\/li\u003e\n  \u003cli\u003eTwo epoxy kits and a printed installation manual are in the box\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003cdiv class=\"nvn-trust\"\u003e\n  \u003ch2\u003eWhy Buy from NVN Marine\u003c\/h2\u003e\n  \u003cul\u003e\n    \u003cli\u003eAuthorized BPS Marine reseller, full manufacturer warranty\u003c\/li\u003e\n    \u003cli\u003eNMEA member and ABYC certified, advice from real boat techs\u003c\/li\u003e\n    \u003cli\u003eSame-day shipping before 3 PM ET on in-stock items\u003c\/li\u003e\n    \u003cli\u003eNY headquarters and Fort Lauderdale flagship retail store\u003c\/li\u003e\n  \u003c\/ul\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eFrequently Asked Questions\u003c\/h2\u003e\n\u003cdiv class=\"nvn-faq\"\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eHow big a boat does the BPS-6 cover?\u003c\/summary\u003e\n    \u003cp\u003eOne BPS-6 system is rated for hulls up to 65ft in length. For larger boats, BPS Marine says you can combine it with additional systems.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWill this work on a boat with stern drives or pods?\u003c\/summary\u003e\n    \u003cp\u003eYes. BPS Marine positions the BPS-6 as a single system that can cover the whole boat on vessels under 52ft with pods or stern drives, including the drives, rudders, and stabilizers.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eDo I have to drill or cut through the hull?\u003c\/summary\u003e\n    \u003cp\u003eNo. The transducers install directly on the hull surface using the epoxy that's provided, so there are no thru-hulls.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhat's included in the box?\u003c\/summary\u003e\n    \u003cp\u003eYou get one BPS-6 control module with an integrated power cable, six submersible ultrasonic transducers with 15ft of cable each, three additional 15ft extension cables, two epoxy kits, and a printed installation and operation manual.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhat voltage does it run on?\u003c\/summary\u003e\n    \u003cp\u003eThe specs list 12V or 24V DC. This listing is the 12VDC version.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eHow much power does it draw?\u003c\/summary\u003e\n    \u003cp\u003eAverage power draw is listed at 1.5Ah. It's a good idea to keep that in mind if your boat runs on battery power alone for long periods.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eHow do I wire it in?\u003c\/summary\u003e\n    \u003cp\u003eIt's a two-wire connection to your house battery bank or distribution panel. The control module has an integrated power cable.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eWhat frequencies does it use?\u003c\/summary\u003e\n    \u003cp\u003eThe system uses a multi-frequency ultrasonic sweep algorithm from 20kHz to 42kHz, with each transducer rated at 60W.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eIs it safe for marine life?\u003c\/summary\u003e\n    \u003cp\u003eBPS Marine says the frequencies used are outside the hearing range of marine mammals and humans, and the system is chemical-free and doesn't leach pollutants into the water.\u003c\/p\u003e\n  \u003c\/details\u003e\n  \u003cdetails\u003e\n    \u003csummary\u003eDoes it need regular maintenance?\u003c\/summary\u003e\n    \u003cp\u003eBPS Marine describes it as a fit and forget system with no scheduled maintenance once it's installed.\u003c\/p\u003e\n  \u003c\/details\u003e\n\u003c\/div\u003e\n\n\u003ch2\u003eTechnical Specifications\u003c\/h2\u003e\n\u003ctable class=\"nvn-specs\"\u003e\n  \u003ctbody\u003e\n    \u003ctr\u003e\n\u003cth\u003eTitle\u003c\/th\u003e\n\u003ctd\u003eBPS Marine BPS-6 6-Transducer Ultrasonic Antifouling System - 12VDC\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eBrand\u003c\/th\u003e\n\u003ctd\u003eBPS Marine\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eManufacturer Part Number\u003c\/th\u003e\n\u003ctd\u003eBPS-6\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eUPC\u003c\/th\u003e\n\u003ctd\u003e703670216299\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eNumber of Transducers\u003c\/th\u003e\n\u003ctd\u003e6\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eVoltage\u003c\/th\u003e\n\u003ctd\u003e12V or 24V DC\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eAverage Power Draw\u003c\/th\u003e\n\u003ctd\u003e1.5Ah\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eTransducer Strength\u003c\/th\u003e\n\u003ctd\u003e60W\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eCable Length\u003c\/th\u003e\n\u003ctd\u003e15ft per transducer\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eFrequency\u003c\/th\u003e\n\u003ctd\u003eMulti-frequency ultrasonic sweep algorithm (20kHz-42kHz)\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eExtension Cables\u003c\/th\u003e\n\u003ctd\u003e3x 15ft\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eEpoxy Kits\u003c\/th\u003e\n\u003ctd\u003e2\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eMaximum Hull Length\u003c\/th\u003e\n\u003ctd\u003eUp to 65ft\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003eWeight\u003c\/th\u003e\n\u003ctd\u003e16.15 lb\u003c\/td\u003e\n\u003c\/tr\u003e\n    \u003ctr\u003e\n\u003cth\u003ePackage Dimensions (L x W x H)\u003c\/th\u003e\n\u003ctd\u003e16 x 14 x 6 in\u003c\/td\u003e\n\u003c\/tr\u003e\n  \u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003cscript type=\"application\/ld+json\"\u003e\n{\n    \"@context\": \"https:\/\/schema.org\",\n    \"@type\": \"FAQPage\",\n    \"mainEntity\": [\n        {\n            \"@type\": \"Question\",\n            \"name\": \"How big a boat does the BPS-6 cover?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"One BPS-6 system is rated for hulls up to 65ft in length. For larger boats, BPS Marine says you can combine it with additional systems.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Will this work on a boat with stern drives or pods?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Yes. BPS Marine positions the BPS-6 as a single system that can cover the whole boat on vessels under 52ft with pods or stern drives, including the drives, rudders, and stabilizers.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Do I have to drill or cut through the hull?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"No. The transducers install directly on the hull surface using the epoxy that's provided, so there are no thru-hulls.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"What's included in the box?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"You get one BPS-6 control module with an integrated power cable, six submersible ultrasonic transducers with 15ft of cable each, three additional 15ft extension cables, two epoxy kits, and a printed installation and operation manual.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"What voltage does it run on?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"The specs list 12V or 24V DC. This listing is the 12VDC version.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"How much power does it draw?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"Average power draw is listed at 1.5Ah. It's a good idea to keep that in mind if your boat runs on battery power alone for long periods.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"How do I wire it in?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"It's a two-wire connection to your house battery bank or distribution panel. The control module has an integrated power cable.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"What frequencies does it use?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"The system uses a multi-frequency ultrasonic sweep algorithm from 20kHz to 42kHz, with each transducer rated at 60W.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Is it safe for marine life?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"BPS Marine says the frequencies used are outside the hearing range of marine mammals and humans, and the system is chemical-free and doesn't leach pollutants into the water.\"\n            }\n        },\n        {\n            \"@type\": \"Question\",\n            \"name\": \"Does it need regular maintenance?\",\n            \"acceptedAnswer\": {\n                \"@type\": \"Answer\",\n                \"text\": \"BPS Marine describes it as a fit and forget system with no scheduled maintenance once it's installed.\"\n            }\n        }\n    ]\n}\n\u003c\/script\u003e\n","brand":"BPS Marine","offers":[{"title":"Default Title","offer_id":68049496604765,"sku":"112021","price":2624.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0299\/7266\/0317\/files\/112021XL.jpg?v=1794955651","url":"https:\/\/nvnmarine.com\/products\/bps-marine-bps-6-ultrasonic-antifouling-system","provider":"NVN Marine","version":"1.0","type":"link"}