Bluewater

Bluewater 9150-1130-506 19mm Pre-Wired Push Button Switch

SKU: 1004886 · UPC: 810196333734 · MPN: 9150-1130-506
★★★★★ 4.7 · 0 reviews
Authorized dealer
$25.00
or 4 payments of $6.25 with Affirm · See disclosures
In stock — Ships today Pickup Monday · Fort Lauderdale (FL)
SAME-DAY SHIPPING · 14:23 EST
Order in time, ships today
Ships from your nearest warehouse. UPS Ground 2–4 business days.
Free shipping
Orders $500 or more
Free returns
Within 30 days
Same day shipping
Order before 3 PM (EST)
Ask anything
We're here to help
$25.00
02 · Overview

Bluewater 9150-1130-506 19mm Pre-Wired Push Button Switch — Product description

The Bluewater 9150-1130-506 is a 19mm pre-wired, latching on/off push button switch with a black body and a translucent ring that shows blue when off and red when on. It's IP67 sealed with a 6-inch epoxy-sealed harness, so it drops into a tight dash and wires up fast.

This is the Bluewater 9150-1130-506, a 19mm pre-wired mechanical push button switch with latching on/off action. Push once and the circuit is on. Push again and it's off. The body is black, so it disappears into a dark dash or switch panel, and the translucent blue ring gives you a clear status light right where you're looking. It ships with a 5-wire harness and 6-inch leads already attached and epoxy sealed, so you're not crimping tiny terminals onto a switch before you can even mount it.

Installation is about as straightforward as switch work gets. Drill a 19mm hole in material up to 6mm thick, seat the switch, and secure it. The integrated gasket seals against the panel, and the leads are color coded, which takes most of the guesswork out of the wiring. The low-profile design is what makes it a good fit for tight dashboards and panels where a bulky rocker just won't go. Measure your panel thickness before you cut anything. Anything over 6mm is outside the stated range, and it's a lot easier to check first than to fix a bad hole later.

The ring does more than look good. It shows blue when the switch is inactive and red when it's active. That's useful on a helm at night, or on a crowded panel where you want to read the state of a circuit without leaning in. Just remember the logic before you label anything. Blue doesn't mean on here. Blue means off, and red means the circuit is live. If you're building a panel with several of these, a little label under each one saves a lot of second guessing later.

On the numbers, the switch is rated 10A @ 12VDC. Protection is IP67, and the sealed design with the integrated gasket is meant for wet marine environments, so it belongs on an open console, a boat's helm, or a trailer-side panel just as much as inside a cabin. Mechanical life is listed at 500,000 cycles and electrical life at 10,000 cycles. Those are two different figures, and the electrical one is the lower number, so keep that in mind if you plan to cycle something under load all day long. For a bilge pump override, a courtesy light, or an accessory feed you flip a handful of times a trip, it's plenty.

A few practical notes from the install side. Six-inch leads are short, which is fine for plug-and-play at the back of a panel but means you'll usually be splicing close behind the dash. Heat-shrink butt connectors and a little strain relief keep vibration from fatiguing the wires over time. If the load you're switching is anywhere near the 10A rating, think about driving a relay with the switch and fusing the supply, rather than pushing the full current through the switch contacts. And confirm that you want latching action before you drill. This one is latching on/off, not momentary.

One more honest note. The listing gives a 12VDC rating and doesn't state a 24V rating or any ignition-protection rating, so don't assume either. If your boat runs a 24V system, or you're wiring into a gasoline engine space, check that before you buy.

Bluewater builds these for boats, RVs and vehicles, and that range makes sense. It's a compact, clean switch with a visible indicator, a gasket, and a pre-wired harness. If you're tidying up a dash, adding an accessory circuit, or replacing a tired switch on a panel, this one gets the job done without a lot of fuss. It's also easy to spec for a whole panel, since matching switches keep the helm looking tidy and consistent.

Key Features

  • 19mm pre-wired push button, so it fits tight dashboards and panels where a rocker won't
  • Latching on/off action, push once for on and again for off
  • Translucent ring shows blue when inactive and red when active, so you can read circuit state at a glance
  • Epoxy-sealed 5-wire harness with 6-inch color-coded leads, ready for plug-and-play wiring
  • IP67 rating with integrated gasket, built for wet marine environments
  • 10A @ 12VDC switch rating covers typical accessory circuits
  • 500,000 mechanical cycles and 10,000 electrical cycles
  • Mounts in a 19mm hole, in material up to 6mm thick

Why Buy from NVN Marine

  • Authorized Bluewater reseller, full manufacturer warranty
  • NMEA member and ABYC certified, advice from real boat techs
  • Same-day shipping before 3 PM ET on in-stock items
  • NY headquarters and Fort Lauderdale flagship retail store
NVN Marine — 11 W State Road 84, Fort Lauderdale, FL 33315 Available for pickup at our Fort Lauderdale store (Monday) $25.00
03 · The numbers

Technical specifications

Title Bluewater 19mm Pre-Wired Mechanical Push Button Switch, On/Off, Black Body, Translucent Blue Ring, 6" Leads
Brand Bluewater
Manufacturer Part Number 9150-1130-506
UPC 810196333734
Switch Type Mechanical push button
Function On/Off (latching)
Body / Face Black body, translucent blue LED ring
Switch Diameter 19mm
Switch Rating 10A @ 12VDC
LED Indicators Blue inactive / Red active
Wiring 5-wire, epoxy-sealed, 6 in. leads
Protection Rating IP67
Mechanical Life 500,000 cycles
Electrical Life 10,000 cycles
Mounting Hole 19mm
Panel Thickness Up to 6mm
Category Electrical
04 · Before you buy

Frequently asked questions

What size hole does the Bluewater 9150-1130-506 need?

It needs a 19mm hole. The listing says to drill in material up to 6mm thick.

Is this switch latching or momentary?

It's latching on/off. Push once for on, push again for off.

What do the blue and red ring colors mean?

The translucent ring is blue when the switch is inactive and red when it's active.

Is it waterproof?

It has an IP67 protection rating and an integrated gasket, and it's described as a sealed design for wet marine environments. Use the gasket against the panel when you mount it.

What is the current rating?

The switch rating is 10A @ 12VDC.

Does it come pre-wired?

Yes. It's a pre-wired, epoxy-sealed 5-wire harness with 6-inch leads. The leads are color coded to simplify wiring.

How thick can the mounting panel be?

Up to 6mm. Measure your panel before you drill.

Can I use it on a 24V system?

The published rating is 10A @ 12VDC. The listing doesn't give a 24V rating, so we can't confirm it for 24V.

Is this an ignition-protected switch?

The listing doesn't say it is, so don't assume it. Check before using it in a gasoline engine space.

How many cycles is it rated for?

Mechanical life is 500,000 cycles and electrical life is 10,000 cycles.

05 · Customer voices

Customer reviews