Bluewater 19mm Push Button Switch, On/Off, Blue Ring
Bluewater 19mm Push Button Switch, On/Off, Blue Ring — Product description
The Bluewater 9150-1100-506 is a pre-wired 19mm latching on/off push button switch with a translucent blue LED ring that turns red when the circuit's active. It's sealed to IP67, comes with 6-inch leads, and fits panels up to 6mm thick. A clean, easy-to-read control for your helm or dash.
The Bluewater 9150-1100-506 is a 19mm pre-wired mechanical push button switch with a translucent blue illuminated ring. It's a latching on/off switch. Push once and the circuit is on, push again and it's off. That's it. No toggle lever to snag a sleeve, no rocker to catch a knee in a tight cockpit.
This one's built for the places on a boat where panel space is scarce and the spray is real. Think dash panels on a center console, switch banks at a helm, livewell and bilge pump controls, courtesy lights, or a stern station that gets rinsed down after every trip. Bluewater designs its 19mm mechanical push button switches as low-profile, marine-grade switches for tight dashboards and panels on boats, RVs and vehicles, so the same switch also works in a camper or a work truck.
The ring does a lot of the talking. When the switch is inactive, the translucent blue LED ring glows blue. When the circuit is active, the ring switches to red. You can read the state of a circuit from across the helm without touching anything, and that's a real help at night when you're trying to figure out what's running without hunting for a flashlight. It's a small thing until the first time you leave a pump running by mistake.
Wiring is where this switch saves you time. It comes pre-wired with a factory-sealed 5-wire harness, and the leads are 6 inches long. The leads are color-coded, which makes the hookup easier to follow, and the harness is epoxy sealed at the factory so you aren't dealing with a bare solder joint behind the panel. Six inches is short, so plan on a terminal strip, a connector, or an extension to reach your bus bar and fuse block. Measure your run before you start.
Mounting is simple. Drill a 19mm hole in material up to 6mm thick and drop the switch in. That covers most fiberglass panels, aluminum plates, and thin acrylic or HDPE switch panels. If your panel is thicker than 6mm, you'll need to relieve the back side so the switch can seat properly. Always check the thickness first, because it's the number that trips people up most often on a retrofit.
Protection is rated IP67, with an integrated gasket for wet marine environments. That's a sealed design meant for the spray and splash that hits helm panels. It's a good fit for exposed stations, though you'll still want to think about where the back of the switch and your wiring end up. Keep connections up high and tidy, use heat shrink, and don't leave a splice sitting in a bilge puddle.
On the electrical side, the switch rating is 10A at 12VDC. That's plenty for lighting, small pumps, blowers, and accessories on a 12V system, but it isn't meant for a big load like a windlass or a thruster. For anything heavy, use this switch to trigger a relay and let the relay carry the current. And fuse the circuit properly, no matter what you're switching. The switch protects nothing, it only controls.
Construction uses nickel-plated brass and stainless steel, with a metal actuator surrounded by the translucent blue ring. Bluewater lists a mechanical life of 500,000 cycles and an electrical life of 10,000 cycles. In plain terms, you can press it a very long time, and it's rated to switch a load thousands of times. For a control you'll hit every trip, that's the kind of number you want to see.
A few practical notes before you order. This is the On/Off latching version with the blue ring, so if you need a momentary action for something like a horn or a bow thruster trigger, this isn't the right switch for that job. Make sure you've got a 19mm hole, a panel 6mm thick or less, and a plan for the 6-inch leads. If those three boxes are checked, this is a clean, simple way to add a good-looking, easy-to-read control to your dash.
Key Features
- 19mm pre-wired mechanical push button, so it drops into a standard 19mm panel hole with no extra hardware hunting
- Latching on/off action, push once for on and again for off, with no lever to snag
- Translucent blue LED ring, blue when inactive and red when the circuit is active, so you can read status at a glance
- Factory-sealed, epoxy-sealed 5-wire harness with 6-inch color-coded leads for simpler hookup
- IP67 waterproof rating with an integrated gasket, built for wet marine panels
- 10A at 12VDC switch rating covers lighting, small pumps and accessories
- Nickel-plated brass and stainless steel construction with a metal actuator
- 500,000-cycle mechanical life and 10,000-cycle electrical life
- Fits panels up to 6mm thick, which covers most helm and dash panels
Why Buy from NVN Marine
- Authorized Bluewater reseller, full manufacturer warranty
- NMEA member and ABYC certified, advice from real boat techs
- Same-day shipping before 3 PM ET on in-stock items
- NY headquarters and Fort Lauderdale flagship retail store
Technical specifications
| Title | Bluewater 19mm Pre-Wired Mechanical Push Button Switch, On/Off, Translucent Blue Ring, 6" Leads |
|---|---|
| Brand | Bluewater |
| Manufacturer Part Number | 9150-1100-506 |
| UPC | 810196332591 |
| Function | On/Off (latching) |
| Face Style | Metal actuator with translucent blue LED ring |
| Switch Rating | 10A @ 12VDC |
| LED Indicators | Blue inactive / Red active |
| Wiring | 5-wire, epoxy-sealed, 6 in. leads |
| Protection Rating | IP67 |
| Material | Nickel-plated brass / stainless steel |
| Mechanical Life | 500,000 cycles |
| Electrical Life | 10,000 cycles |
| Mounting Hole | 19mm, material up to 6mm thick |
| Category | Electrical |
Frequently asked questions
What size hole does the Bluewater 9150-1100-506 need?
It needs a 19mm hole. The switch mounts in material up to 6mm thick.
Is this switch latching or momentary?
It's latching on/off. Push once for on and push again for off.
What do the LED colors mean?
The translucent ring glows blue when the switch is inactive and switches to red when the circuit is active.
Is the switch waterproof?
It's rated IP67 and uses an integrated gasket for wet marine environments. Keep your wiring connections protected too.
How long are the wires?
The pre-wired harness is a 5-wire, epoxy-sealed harness with 6-inch leads. You may need a connector or extension to reach your fuse block or bus bar.
What's the electrical rating?
The switch rating is 10A at 12VDC.
Can I use it on an RV or truck?
Yes. Bluewater's 19mm mechanical push button switches are made for tight dashboards and panels on boats, RVs and vehicles.
What's it made of?
The materials are nickel-plated brass and stainless steel, with a metal actuator and a translucent blue LED ring.
How many times can it be pressed?
Bluewater lists a mechanical life of 500,000 cycles and an electrical life of 10,000 cycles.