Bluewater 20 Position DTB Busbar, Dual 5/16" Stud 2312-D-256
Bluewater 20 Position DTB Busbar, Dual 5/16" Stud 2312-D-256 — Product description
The Bluewater 20 Position DTB Busbar (2312-D-256) puts twenty sealed connector positions and two 5/16" studs on one tin-plated copper plate. It's rated 350A at 48V DC, so you can clean up helm and engine room wiring with a plug-in harness that stands up to vibration, moisture, and salt air.
If you've ever tried to tidy up a pile of DC leads behind a helm panel, you know how fast it turns into a rat's nest. This Bluewater 20 Position DTB Busbar (model 2312-D-256) is built to fix that. It gives you twenty sealed connector positions on one plate, plus two 5/16" studs for your heavy feeds, so power distribution lives in one clean, serviceable spot.
The positions are split between 16 DT and 4 DTP style male connections. That mix is handy because you can run lighter signal and accessory circuits on the DT positions and use the DTP positions where a circuit needs a bit more current. The bar accepts wire from 20 AWG up to 12 AWG, which covers the usual run of nav lights, pumps, electronics feeds, and accessory circuits on most boats and mobile rigs.
Bluewater rates it at 350A at 48V DC. That's the number to design around, and it tells you this isn't a toy distribution block. Underneath, there's a 2 mm thick tin-plated copper plate. Tin plating matters out there because salt air eats bare copper, and a corroded bus is a voltage drop waiting to happen. The studs are FHS-0518-12 stainless steel with 5/16" hardware, so the high-current connections stay tight and resist rust.
Mating is simple. The bar pairs with the female DTB06-20S connector, so you build your harness side with that housing and plug it straight in. Because the connections are sealed, they're a good fit anywhere vibration, moisture, and corrosion are part of daily life. Think engine rooms, bilges, console interiors, trailer rigs, and heavy equipment.
Installation is straightforward. There are integrated mounting holes, so you can fasten the bar to a panel or backer without hunting for extra brackets. The mounting holes measure 0.20" and sit 2.87" apart. The mounting screw size is #10 or 1/4" (two screws). Measure your backer before you drill, and mount it somewhere high and dry with the studs accessible for wrenching.
A few practical notes from the dock. The 5/16" studs are meant for your main feeders, so use properly sized lugs and crimp them correctly. Tighten the hardware snugly and recheck it after the first few heat cycles, since loose studs are the classic failure on any busbar. And remember the bar is a distribution point, not overcurrent protection. Every circuit leaving it still needs the right fuse or breaker for the wire size.
Who is it for? Anyone rebuilding a helm, adding a second electronics bank, or cleaning up a boat that's grown a decade of add-on wiring. It also suits builders and installers who want a repeatable, plug-in harness approach instead of dozens of ring terminals stacked on a single stud. If you're not using Deutsch style sealed connectors, this isn't the bar for you. It's designed specifically around them.
What's it not? It's not a bus with built-in fuse protection, and it doesn't come with the female connectors or wire. Plan on buying the mating DTB06-20S housings and the contacts you need separately. We'd rather tell you that now than have you find out halfway through an install.
One more thing worth planning for is layout. Twenty positions fill up faster than you'd think on a cruiser with a full DC panel, so count your circuits first and leave yourself a few spares for the next gear upgrade. Label both ends of every lead, keep the heavy feeder cables short and direct, and use a non-conductive backer. Ten minutes of planning now saves an afternoon of tracing wires later.
We're an authorized Bluewater reseller, and if you're not sure how to size the feeds or lay out your distribution, our crew is happy to talk it through before you order. A tidy, sealed power distribution point is one of those upgrades you stop thinking about, and that's exactly what you want from it.
Key Features
- 20 sealed positions (16 DT and 4 DTP male) so you can feed a whole panel of circuits from one plate.
- Accepts 20 AWG to 12 AWG wire, covering most accessory, lighting, and electronics circuits.
- Rated 350A at 48V DC for high-current distribution that's built for 12V, 24V, and 48V systems.
- 2 mm thick tin-plated copper plate for stable conductivity and corrosion resistance.
- Dual 5/16" studs with FHS-0518-12 stainless steel hardware for secure main feeder connections.
- Mates with the female DTB06-20S connector for a clean plug-in harness.
- Integrated mounting holes, 2.87" apart, for simple panel or backer installation.
- Sealed design suited to vibration, moisture, and salt air on boats and mobile equipment.
Why Buy from NVN Marine
- Authorized Bluewater reseller, full manufacturer warranty
- NMEA member and ABYC certified, advice from real boat techs
- Same-day shipping before 3 PM ET on in-stock items
- NY headquarters and Fort Lauderdale flagship retail store
Technical specifications
| Title | Bluewater 20 Position DTB Busbar Dual 5/16" stud |
|---|---|
| Brand | Bluewater |
| Manufacturer Part Number | 2312-D-256 |
| UPC | 810196334526 |
| Model | 2312-D-256 |
| Positions | 20 |
| Connector Types | 16 DT and 4 DTP (Male) |
| Wire Gauge Range | 20 AWG to 12 AWG |
| Rating | 350A at 48V DC |
| Plate | 2 mm thick tin-plated copper |
| Studs | FHS-0518-12 stainless steel |
| Stud Size | 5/16" |
| Mating Connector | Female DTB06-20S |
| Mounting Holes | 0.20" |
| Distance Between Mounting Holes | 2.87" |
| Mounting Screw Size (2) | #10, 1/4" |
| Category | Electrical |
Frequently asked questions
How many circuits can this busbar handle?
It has 20 positions, split between 16 DT and 4 DTP male connections. That's twenty separate circuits on one plate, plus the two 5/16" studs for your main feeds.
What wire gauges does it support?
The bar supports wire from 20 AWG to 12 AWG on the connector positions. Use the 5/16" studs with properly sized lugs for heavier feeder cables.
What's the current and voltage rating?
Bluewater rates it at 350A at 48V DC. Always size your wire and fusing for each circuit separately, since the bar's rating isn't the limit for any single branch.
What mates with this busbar?
It mates with the female DTB06-20S connector. The female housings and contacts aren't included, so plan to buy them separately.
What are the studs and plate made of?
The plate is 2 mm thick tin-plated copper, and the studs are FHS-0518-12 stainless steel with 5/16" hardware.
How do I mount it?
It has integrated mounting holes. The holes measure 0.20" and sit 2.87" apart, and the mounting screw size is #10 or 1/4" (two screws).
Does it include circuit protection?
No. It's a distribution busbar, so every circuit leaving it still needs its own fuse or breaker sized for the wire.
Is it suitable for marine use?
Yes. Bluewater designed it for marine, heavy equipment, and mobile applications where vibration, moisture, and corrosion are concerns.