Attwood 15240-G 4-Step Pontoon Ladder, Anodized Aluminum
Attwood 15240-G 4-Step Pontoon Ladder, Anodized Aluminum — Product description
The Attwood 15240-G is a 4-step aluminum pontoon ladder with an anodized silver finish. It extends to 50 inches, carries 250 pounds, and mounts permanently or removably with Shur-Loc catches. It's a simple way to get swimmers back aboard your pontoon.
If you've got a pontoon and you're tired of hauling yourself over the gate every time you want a swim, a ladder is the fix. The Attwood 15240-G is a 4-step aluminum pontoon ladder with an anodized silver finish. It's built around a simple idea. Put four steps where you need them, make it light enough to handle, and let you choose whether it stays bolted on or comes off when you're done for the day.
The mount is the part worth talking about. This ladder is listed as a permanent or removable mount, and it comes with Shur-Loc catches. So you can fix it in place on a boat that lives at one dock and sees a lot of swimmers, or take it off for trailering, storage, or a rafted-up weekend when the deck needs to be clear. Which way you go depends on how you use the boat. We'd say if the ladder gets used every outing, leave it mounted. If it's an occasional thing, removable makes more sense.
Size matters on a ladder, so here are the numbers. It's 15 inches wide and extends to 50 inches long. There are 4 steps, and the rated load capacity is 250 pounds. It's a without-rails design, which means there are no side handrails built into the ladder itself. Some boaters like that clean look and the way it tucks away. Others want something to grab. Know which camp you're in before you order.
That 50 inch extended length is the number to check against your own boat. Measure from the pontoon deck edge down to the waterline with the boat loaded the way you normally run it, then think about how far below the surface you want the bottom step to sit. A ladder that's too short leaves you reaching for the first rung, and nobody enjoys that after a swim. Take the tape measure out to the boat first. It takes a minute and saves a return.
The 250 pound rating is also worth a straight look. It's a solid rating for a swim ladder used one person at a time, and plenty of families get by fine with it. Just remember it's the load limit for the ladder, so wet gear and a heavy climber add up. If your crew skews heavier, think about whether this is the right fit before you commit. We'd rather you buy the right ladder once than the wrong one twice.
Aluminum is the material here, with an anodized finish in silver. Anodizing hardens and seals the surface, which is why aluminum gear holds up around water as well as it does. It's still metal on a boat, though. Rinse it after a day in salt, and keep an eye on the spots where it meets the mount, because that's where scratches in the finish tend to show up first. Freshwater lakes are the easiest environment for it, but plenty of boaters run aluminum ladders on the coast with a regular rinse habit.
Installation is a deck-side job, and the surface matters. The catches need a flat, solid place to land. If your pontoon has a crowned deck, soft spots, or rail hardware crowding the area where the ladder goes, plan for that before you drill anything. A quick dry fit with the ladder held against the spot will tell you most of what you need to know. Mark your holes, double check, and then go. Use fasteners suited to your deck material, and check them from time to time since a ladder takes real use.
Where does this ladder make sense? Lake pontoons with a swim platform edge or a low-freeboard side, family boats where kids and adults climb back aboard all afternoon, and fishing pontoons that anchor up for a swim break. Where might it fall short? Boats with a tall deck above the water, since 50 inches only goes so far. And any situation where a climber really needs handrails, because this model doesn't have them.
A few practical habits help any ladder last. Rinse it after use, don't leave it hanging in the water for weeks if you can avoid it, and look it over at the start of every season. Check the catches, check the mounting points, and make sure nothing has loosened. Four steps see a lot of wet feet. A little attention keeps it feeling solid underfoot.
One more note on the details. The title carries the specs we've covered here: 4 steps, 250 pound load capacity, 15 inch width, 50 inch extended length, without rails, anodized silver aluminum, and Shur-Loc catches. We haven't listed anything beyond those facts, because we'd rather give you honest numbers than filler. If you need a spec we haven't shown, ask the crew and we'll help you sort it out before you buy.
Key Features
- 4 steps give you a clear, stepwise climb back aboard after a swim.
- Permanent or removable mount lets you bolt it on for good or take it off for storage.
- Shur-Loc catches are included in the listing, which means the ladder is ready for its mount.
- 250 pound load capacity covers one swimmer at a time, so plan around your heaviest climber.
- 15 inch width gives a compact footprint on the pontoon deck edge.
- 50 inch extended length reaches down to the water on boats with moderate deck height.
- Without rails keeps the profile clean, though you won't get built-in handholds.
- Anodized aluminum finish resists the water and weather you'll put it through.
- Silver finish blends with most pontoon rail and trim colors.
Why Buy from NVN Marine
- Authorized Attwood Marine reseller, full manufacturer warranty
- NMEA member and ABYC certified, advice from real boat techs
- Same-day shipping before 3 PM ET on in-stock items
- NY headquarters and Fort Lauderdale flagship retail store
Technical specifications
| Title | Pontoon Ladder; 4 Step; Permanent Or Removable Mount; 250 Pound Load Capacity; 15 Inch Width x 50 Inch Extended Length; Without Rails; Anodized; Silver; Aluminum; With Shur-Loc Catches |
|---|---|
| Brand | Attwood Marine |
| Manufacturer Part Number | 15240-G |
| UPC | 038203152400 |
| Product Type | Pontoon Ladder |
| Number of Steps | 4 |
| Mount Type | Permanent Or Removable |
| Load Capacity | 250 Pound |
| Width | 15 Inch |
| Extended Length | 50 Inch |
| Rails | Without Rails |
| Finish | Anodized |
| Color | Silver |
| Material | Aluminum |
| Catches | Shur-Loc |
Frequently asked questions
How many steps does the Attwood 15240-G pontoon ladder have?
It has 4 steps. The 50 inch extended length is the full length with the ladder deployed.
What is the weight capacity?
The listing gives a 250 pound load capacity. Treat that as the limit for one person climbing at a time, wet gear included.
Can I leave this ladder permanently mounted?
Yes. It's listed as a permanent or removable mount, so you can fix it in place or take it off when you want the deck clear.
Does it have handrails?
No. It's a without-rails design, so there are no side handrails on the ladder. If you want something to hold while climbing, plan on using a rail or grab handle on the boat.
What are the dimensions?
It's 15 inches wide and 50 inches long when extended.
What is it made of?
It's aluminum with an anodized finish in silver.
What are Shur-Loc catches?
The listing says the ladder comes with Shur-Loc catches, which are the hardware that works with the mount. We don't have further detail on the catch design, so check the manufacturer's instructions when you install.
How do I know if 50 inches is long enough for my boat?
Measure from the deck edge to the waterline with the boat loaded as you normally run it. Then decide how far below the surface you want the bottom step. If the bottom step would hang above the water, you'd want a longer ladder.
Is it a good fit for saltwater use?
Anodized aluminum can be used near salt, but rinse it after use and watch the mounting spots where scratches can start. Freshwater is gentler on it.
What's the manufacturer part number?
It's 15240-G, from Attwood Marine, with UPC 038203152400.