Airmar UDST820 TriSonic Thru-Hull Transducer, N2K
Airmar UDST820 TriSonic Thru-Hull Transducer, N2K — Product description
The Airmar UDST820 TriSonic gives you depth, ultrasonic speed, water temperature, and heel and trim data from one plastic thru-hull sensor. No paddlewheel means no cleaning and no replacing. It sends calibrated data over NMEA 2000, and you calibrate it from your phone.
The Airmar UDST820 TriSonic is a plastic thru-hull sensor that packs depth, speed through water, water temperature, and heel and trim data into one housing. The speed side is ultrasonic, so there's no paddlewheel to foul, clean, or replace. If you've ever pulled a growth-covered paddlewheel at the dock and cursed quietly, you already know why that matters.
Everything goes out over NMEA 2000. The sensor puts calibrated data on the backbone, and every instrument and display on that network can read it. You wire in one drop cable and you're done. It comes with a 6 m (20') NMEA 2000 cable and a Micro connector, and it draws 80 mA to 200 mA (125 mA average) at 12 VDC. It runs on 9 to 16 VDC and has an NMEA 2000 LEN of 6, so add that to your network load calculation before you tap in.
The ultrasonic speed solution has no moving parts. Airmar says Adaptive Signal Processing adjusts to boat speed, water depth, and water clarity to keep speed readings consistent. Data updates up to 10 times per second. Speed range is 0.1 to 35 knots (40 MPH), which covers a slow sailboat in light air and a good deal of power cruisers too. Depth range runs from 0.6 m (2') to 100 m (328') on a 235 kHz frequency band, and the power rating is 100 W.
Sailors get extra out of this one. The built-in heel and trim data goes onto the network alongside depth and speed, so heel-compensated speed through water is possible. That's a big deal if you race or you just like trimming for real numbers instead of guesses.
Calibration happens from your phone. The sensor has Bluetooth BLE and talks to Airmar's CAST app, which walks you through a guided calibration. You can apply depth offsets for depth below keel or depth from surface, switch NMEA 2000 PGNs on or off, and set other offsets from the menus. For advanced speed calibration you can enter custom speeds for up to four heel angles and up to ten speeds. Wireless range is up to 30' depending on where you mount it. Settings are stored in the sensor itself, so they stay put.
Retrofit is a strong selling point. The UDST820 fits most existing Airmar 2" housings, with a hole size of 51 mm (2") and a usable shaft length of 57 mm (2.25"). It's a low-profile thru-hull mount in plastic, suitable for fiberglass or metal hulls, saltwater or freshwater. That means if you're already running an Airmar paddlewheel or depth sensor in a 2" housing, there's a good chance you can swap this in without cutting a new hole. Check your housing before you order, because fit depends on what's already in the hull. This listing is the sensor itself. Housings and other hardware are sold separately unless your order says otherwise.
Who's it for? Cruising and racing sailboats, plus leisure and yachting power boats that want accurate speed without paddlewheel chores. It's also a good fit if you've got an NMEA 2000 backbone and a display that can show speed, depth, temperature, and attitude data. Water temperature reads from -4° to 40°C (24.8° to 104°F) with an accuracy of +0.5°C (+1.0°F).
It's not the pick if your boat has no NMEA 2000 network, since that's the only output here. It also isn't a replacement for a fishfinder transducer. This is a depth, speed, and temperature smart sensor, not a high-power sonar imaging unit.
Weight is 1.4 kg (3 lb.), and the box ships at 2.5 lb. in a 10 x 8 x 4 inch carton. It's made in the USA. We stock Airmar gear because we trust it, and our crew can help you confirm that your housing, cable run, and network all line up before you buy.
Key Features
- Ultrasonic speed sensing with no paddlewheel, so there's no cleaning, wear, or replacement
- Depth, speed, water temperature, and heel and trim data from one thru-hull sensor
- NMEA 2000 output of calibrated data to every instrument and display on the network
- Data updates up to 10 times per second, with a speed range of 0.1 to 35 knots (40 MPH)
- Depth range from 0.6 m (2') to 100 m (328') on a 235 kHz frequency band
- Bluetooth BLE connection to the Airmar CAST app for guided speed and depth calibration
- Advanced speed calibration with custom entries for up to four heel angles and ten speeds
- Retrofits most existing Airmar 2" housings (51 mm hole, 57 mm usable shaft length)
- 6 m (20') NMEA 2000 cable with N2 Micro connector, LEN of 6, 80 to 200 mA at 12 VDC
- Plastic low-profile thru-hull for fiberglass or metal hulls, saltwater or freshwater use
Why Buy from NVN Marine
- Authorized Airmar reseller, full manufacturer warranty
- NMEA member and ABYC certified, advice from real boat techs
- Same-day shipping before 3 PM ET on in-stock items
- NY headquarters and Fort Lauderdale flagship retail store
Technical specifications
| Title | Airmar UDST820 TriSonic Plastic Thru-Hull Transducer - N2K |
|---|---|
| Brand | Airmar |
| Manufacturer Part Number | UDST820P-N2 |
| UPC | 801769030297 |
| Functions | Depth, Speed, Temperature, Attitude |
| Comm Method | NMEA 2000® |
| Bluetooth Capable | YES Bluetooth BLE |
| Wireless Range | Up to 30' depending on mount location |
| Cable Length | 6 m (20') NMEA 2000® cable |
| Display Connector | N2 Micro |
| NMEA 2000 LEN | 6 |
| Voltage | 9 to 16 VDC |
| Power Supply Current | 80 mA - 200 mA, Average 125 mA @12VDC |
| Power Rating | 100 W |
| Frequency Band | 235 kHz |
| Data Rate | Up to 10 times per second |
| Depth Range | Minimum Depth .6 m ( 2'), Maximum Depth 100 m (328') |
| Speed Range | 0.1 to 35 knots (40 MPH) |
| Temperature Accuracy | +0.5°C (+1.0°F) |
| Water Temperature | -4° to 40°C (24.8° to 104°F) |
| Mounting Style | Low Profile Thru-Hull |
| Hole Size | 51 mm (2") |
| Usable Shaft Length | 57 mm (2.25") |
| Hull Material | Fiberglass or metal |
| Material | Plastic |
| Tilted Element | No |
| Retrofits | Fits most Airmar 2" housings |
| Common Use | Cruising/Racing Sailboats, Leisure/Yachting |
| Weight | 1.4 kg (3 lb.) |
| Package Dimensions (L x W x H) | 10.00 x 8.00 x 4.00 in |
| Country of Origin | USA |
Frequently asked questions
Does the UDST820 need a paddlewheel?
No. Speed is measured ultrasonically with no moving parts, so there's no paddlewheel to clean or replace.
What does the TriSonic sensor measure?
It combines depth, ultrasonic speed, water temperature, and heel and trim data in one sensor.
What kind of network does it connect to?
It outputs NMEA 2000 data through a 6 m (20') NMEA 2000 cable with an N2 Micro display connector. It has an NMEA 2000 LEN of 6.
How much power does it draw?
Supply current is 80 mA to 200 mA, averaging 125 mA at 12 VDC. The supply voltage range is 9 to 16 VDC.
Will it fit my existing housing?
It's designed to retrofit most existing Airmar 2" housings. The hole size is 51 mm (2") and the usable shaft length is 57 mm (2.25"). Check what's in your hull before ordering, or ask our crew.
How do I calibrate speed and depth?
Use Airmar's free CAST app over Bluetooth BLE. It offers basic and advanced speed calibration and depth offsets for below keel or from surface.
What's the Bluetooth range?
Wireless range is up to 30' depending on mount location.
What speed and depth ranges does it cover?
Speed runs from 0.1 to 35 knots (40 MPH). Depth runs from 0.6 m (2') to 100 m (328').
Can I use it in saltwater?
Yes. It's suitable for both saltwater and freshwater use.
What hull materials can it go in?
The listed hull material is fiberglass or metal.
How fast does it update?
Data rate is up to 10 times per second.
Does it work for sailboats and power boats?
Yes. It's listed for cruising and racing sailboats and for leisure and yachting boats. Heel and trim data is a bonus for sailors.