Lenco 12" x 9" Standard Performance Trim Tab Kit w/o Switch Kit 12V

Lenco 12" x 9" Standard Performance Trim Tab Kit w/o Switch Kit 12V Product Description

12" x 9" Standard Performance Trim Tab Kit w/o Switch Kit- 12V

Upgraded electro-polished trim blades with stouter 1/4" diameter hinge pin make these Performance Trim Tab Kits a cut above the base level Lenco Standard Mount Kits. Equipped with the same fast response electric actuators for precise control. Fully submersible with all Plug & Play Deutsch connections. Blades are Electro-Polished 12 gauge - 304 SS with 1" turned up edges (the 16" x 12" and the 18" x 14" have an 85 degree inside taper) and 1/4" diameter hinge pin. Kit includes Standard Actuators with 5/16" SS bolts. The actuators mount at the trailing edge of the blades

Kit Contents:

• 2 each of 12-gauge stainless steel Electro-Polished trim tab blades
• 2 each of #15054-001 actuators with 6' lead and Deutsch plugs
• 2 each of #30133-103 20' actuator extension wiring harnesses
• 2 each of #15085-001 (#116) upper mounting bracket with gland seal   
• 2 each of #50014-001 (#119) lower mounting bracket 
• 1 each of the Lenco owner’s / installation manual
• All necessary stainless steel mounting hardware

Specifications:

• Suggested Boat Length: 16' to 26'
• Length of Tab: 12"
• Width of Tab: 9"
• Minimum Transom Height: 11"
• Blades: 12 Gauge Stainless Steel
• Finish: Electro-Polished
• Switch Kit: Sold Separately
• Class: Fuel Efficient
• Compliance: CE Certified
• Compatibility: Any Boat
• Actuators: 12-volt

WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Lenco 12" x 9" standard performance trim kit without switch kit 12V 12" x 9" standard performance trim kit without switch performance 12V upgraded electro-polished trimming blade with 1/4" diameter hinge pin, excellent The performance of the trim label kit is a bit higher than the basic Lenco standard mounting kit. Equipped with the same fast-response electric actuator for precise control. It can fully dive into all plug-and-play Deutsch connections. The blade is electropolished 12 Specifications-304 SS rotated a 1-inch upper edge (16" x 12" and 18" x 14" inner taper is 85 degrees) and a hinge pin with a diameter of 1/4". The kit includes a standard actuator with 5/16" SS bolts.

Lenco 12" x 9" Standard Performance Trim Tab Kit w/o Switch Kit 12V Related Products

Lenco Upper Mounting Bracket w/Gland Seal (2008-Present)
Lenco Compact Upper Mounting Bracket - 2 Screws 1 Wire
Lenco Standard Upper Mounting Bracket - 3 Screws 1 Wire
Lenco Standard Lower Mounting Bracket - 3 Bolt
Tecnoseal R1 Rudder Anode - Zinc - 1-7/8" Diameter
Tecnoseal R2 Rudder Anode - Zinc - 2-13/16" Diameter
Tecnoseal R3 Rudder Anode - Zinc - 3-3/4" Diameter
Tecnoseal R1AL Rudder Anode - Aluminum - 1-7/8" Diameter
Tecnoseal R2AL Rudder Anode - Aluminum - 2-13/16" Diameter
Tecnoseal R3AL Rudder Anode - Aluminum - 3-3/4" Diameter




Save $433 when you buy the Lenco 12" x 9" Standard Performance Trim Tab Kit w/o Switch Kit 12V for only $575 from NVN Marine! Same day shipping before 3pm.