Raymarine SeaTalk 2 / NMEA 2000 Interface Cable (1.5m)
Raymarine SeaTalk 2 / NMEA 2000 Interface Cable (1.5m) — Product description
Unlock seamless communication between your Raymarine E-Series displays and a world of compatible devices with this essential interface cable. Designed for marine environments where reliability is non-negotiable, it bridges the gap between legacy SeaTalk 2 networks and modern NMEA 2000 systems. Whether you're integrating third-party sensors, chartplotters, or autopilots, this 1.5-meter cable ensures your boat's electronics talk to each other without a hitch, keeping you focused on the water ahead.
Key Features That Stand Out on the Water
- Dual-Compatible Design: One end features a twist-lock connector tailored for E-Series displays, while the other sports a rugged 5-pin waterproof SeaTalk 2-style plug—perfect for direct hookups to NMEA 2000 backbones or Raymarine networks.
- Compact 1.5m Length: Long enough for flexible routing in tight console spaces, yet short enough to minimize signal noise and clutter in your helm setup.
- Marine-Tough Build: Fully waterproof and resistant to corrosion, vibration, and UV exposure, it thrives in saltwater spray, pounding waves, and relentless sun.
- Plug-and-Play Simplicity: No complex adapters or custom wiring needed—just connect and power up to share data like GPS position, depth, speed, and heading across your network.
Why This Cable Elevates Your Onboard Electronics
Imagine effortlessly expanding your E-Series setup to include the latest fishfinders, radar units, or engine monitors from other brands. This interface eliminates compatibility headaches, enabling real-time data fusion that sharpens your situational awareness. Boaters report fewer dropped signals and quicker diagnostics during long offshore runs, translating to safer voyages and less downtime. It's not just a cable—it's the backbone that unifies your vessel's tech ecosystem, future-proofing your investment in Raymarine gear.
Step-by-Step Installation for Smooth Sailing
- Prep Your Network: Ensure your SeaTalk 2 backbone or NMEA 2000 spur is powered and terminated correctly—double-check drop cables and T-connectors to avoid bus errors.
- Connect to E-Series: Align the twist-lock end with your display's port, twist securely until it clicks, and route the cable neatly with zip ties to prevent snags.
- Link to Backbone: Plug the 5-pin end into an available SeaTalk 2 socket or NMEA 2000 drop—watch for the satisfying snap that confirms a solid seal.
- Power Cycle and Test: Restart your E-Series unit, navigate to network settings, and verify data flow. Pro tip: Use Raymarine's diagnostic tools to scan for active devices and confirm integration.
- Secure and Waterproof: Apply dielectric grease to connections for extra protection against moisture ingress, especially in open cockpits.
Most installs take under 15 minutes, even for DIYers. If you're dealing with a mixed network, prioritize backbone power at a single point to prevent voltage drops.
Proven Compatibility and Expansion Ideas
This cable shines with E-Series multifunction displays (like E7, E9, or older classics), linking them to SeaTalk 2 instruments or any NMEA 2000-certified gear. Think Lowrance transducers, Garmin autopilots, or Simrad engines—data flows bidirectionally for overlays on your charts. For larger setups, pair it with backbone extenders to connect multiple E-Series units, creating a unified command center. Always match baud rates (typically 4800 for SeaTalk 2, 250k for NMEA 2000) to sidestep communication glitches.
Long-Term Care for Peak Performance
Rinse with fresh water after every salt exposure, inspect connectors quarterly for corrosion, and store spares in a dry locker. If signals falter, swap ends to rule out cable faults—common in high-vibration installs. This durability means one cable often outlasts multiple seasons of heavy use.
Frequently Asked Questions
Interface cable for connecting E-Series displays to Raymarine SeaTalk 2 or 3rd party NMEA 2000 Devices.
Twist-lock connector at the E-series display end, and a standard 5-pin waterproof SeaTalk 2 style connector at the other.
The twist-lock connector on the end of the E series display screen, and the other end is a standard 5-pin waterproof SeaTalk 2 type connector. Raymarine SeaTalk 2 / NMEA 2000 interface cable (1.5m)...
SKU: NVN-16537
MPN: E55053
UPC: 723193550533
Technical specifications
| Brand | Raymarine |
| Model | Raymarine SeaTalk 2 / NMEA 2000 Interface Cable (1.5m) |
| SKU / MFR# | 16537 |
Set product metafields under specs.* to populate this table.
Frequently asked questions
No questions yet. Got one? Drop us a line.
