Bluewater 19mm Momentary Push Button Switch, Blue Ring, 6" Leads
Bluewater 19mm Momentary Push Button Switch, Blue Ring, 6" Leads — Product description
The Bluewater 9150-2100-506 is a 19mm pre-wired momentary push button switch with a translucent blue LED ring. It's sealed to IP67, rated for 10A at 12VDC, and sized for tight helm panels. Press it and the circuit's on. Let go and it's off.
The Bluewater 9150-2100-506 is a 19mm pre-wired mechanical push button switch with a translucent blue illuminated ring. It's a low-profile, marine-grade switch built for tight dashboards and panels on boats, RVs and vehicles. If your helm is crowded and you need a compact control that looks clean and holds up to spray, this is the kind of part you'll end up reaching for.
First thing to understand: this is a momentary switch. The circuit stays on only while the button is held. Let go and it shuts off. That's exactly what you want for a horn, a washdown trigger, or a relay trigger, and exactly what you don't want for something that needs to stay running on its own. Confirm that behavior before you cut a hole in the panel. We'd rather you know now than find out on the water.
The ring does the talking. It glows blue when the switch is inactive and flips to red when the circuit is active. At night that's a clear status check from across the helm. In direct sun, a translucent ring is harder to read, so don't count on it as your only indicator for anything important. Think of it as a helpful glance, not a gauge.
Wiring is already done for you. The switch comes as a factory-sealed, epoxy-sealed 5-wire harness with 6-inch leads, and the leads are color-coded to simplify hookup. Six inches is short, though. Treat the leads as pigtails. Most installs will need extension with tinned marine wire and heat-shrink crimps to reach a fuse block, a relay, or a distribution bus. Plan the wire run before you start so you're not splicing in a cramped space behind the dash.
Sealing is the other big selling point. The switch is rated IP67 and has an integrated gasket for wet marine environments. A gasket only works when it's seated right, though. Drill a true 19mm hole, deburr the edge, and make sure the gasket sits fully flat. This switch mounts in material up to 6mm thick. Check the space behind the panel too, because thick fiberglass or a packed dash can leave little room for the nut and the leads. A sloppy hole is the usual leak path, not the button face.
On the electrical side, the switch is rated for 10A at 12VDC. That's plenty for signal duty and light loads. It's not the right choice for switching high-draw gear like pumps, a windlass, or a thruster directly. Use it to trigger a relay that's sized to the load, and let the relay carry the current. Watch your polarity on the LED leads as well. Follow the color coding, and if the ring stays dark while the switch still clicks, a reversed connection is the first thing to check.
Construction is nickel-plated brass and stainless steel, with a metal actuator face and the translucent blue LED ring around it. The electrical life is listed at 10,000 cycles, which is plenty for a control you press now and then. Because the face is metal, it stays good looking on a helm that sees sun and salt, and the compact 19mm footprint leaves room for neighboring switches.
Where does it fit best? Helm panels, consoles and dash cutouts on center consoles, bay boats, runabouts and small cruisers. It also suits RV and vehicle panels, since Bluewater designs this switch family for all three. One caution. The product information doesn't state an ignition-protection rating, so keep it at the helm and out of engine spaces and fuel areas unless you've verified the part for that use.
We're an authorized Bluewater reseller, so you get the full manufacturer warranty. Have a question about relay sizing or panel layout? Ask our crew and we'll help you sort it out before you drill.
Key Features
- 19mm pre-wired mechanical push button, sized for tight helm panels and dashboards
- Momentary action, the circuit stays on only while the button is held
- Translucent blue LED ring that glows blue when inactive and red when active
- Factory-sealed, epoxy-sealed 5-wire harness with 6-inch color-coded leads for simple hookup
- IP67 waterproof with an integrated gasket for wet marine environments
- 10A at 12VDC switch rating, best used to trigger a relay for heavy loads
- Nickel-plated brass and stainless steel construction with a metal actuator face
- Mounts in a 19mm hole through material up to 6mm thick
Why Buy from NVN Marine
- Authorized Bluewater reseller, full manufacturer warranty
- NMEA member and ABYC certified, advice from real boat techs
- Same-day shipping before 3 PM ET on in-stock items
- NY headquarters and Fort Lauderdale flagship retail store
Technical specifications
| Title | Bluewater 19mm Pre-Wired Mechanical Push Button Switch, Momentary, Translucent Blue Ring, 6" Leads |
|---|---|
| Brand | Bluewater |
| Manufacturer Part Number | 9150-2100-506 |
| UPC | 810196332843 |
| Switch Size | 19mm |
| Function | (On)/Off momentary |
| Face Style | Metal actuator with translucent blue LED ring |
| Switch Rating | 10A @ 12VDC |
| LED Indicators | Blue inactive / Red active |
| Wiring | 5-wire, epoxy-sealed, 6 in. leads |
| Lead Length | 6 in. |
| Protection Rating | IP67 |
| Material | Nickel-plated brass / stainless steel |
| Electrical Life | 10,000 cycles |
| Mounting Hole | 19mm, material up to 6mm thick |
Frequently asked questions
Is this switch momentary or latching?
It's momentary. The function is listed as (On)/Off momentary, so the circuit stays on only while you hold the button. It won't hold a circuit on by itself.
What size hole does it need?
You'll drill a 19mm mounting hole. It's designed for material up to 6mm thick, so check your panel thickness and the space behind it before you cut.
What do the LED ring colors mean?
The translucent ring glows blue when the switch is inactive and switches to red when the circuit is active.
Is it waterproof?
Yes. It carries an IP67 protection rating and has an integrated gasket for wet marine environments. Drill a clean, deburred 19mm hole and seat the gasket fully for the best seal.
How long are the wire leads?
The leads are 6 inches long on a factory-sealed, epoxy-sealed 5-wire harness. They're color-coded to simplify wiring. Most installs will need extra wire to reach a fuse block or relay.
What's the electrical rating?
The switch rating is 10A at 12VDC.
Can I run a bilge pump or windlass directly through it?
We don't recommend it. High-draw loads like pumps, windlasses and thrusters should be switched through a relay sized to the load, with this button used as the trigger.
What is the switch made of?
The material is listed as nickel-plated brass and stainless steel, with a metal actuator face and a translucent blue LED ring.
How many cycles is the electrical life?
The electrical life is listed at 10,000 cycles.
Can I use it outside of boats?
Bluewater describes this style of switch as suited to boats, RVs and vehicles. Just match the 10A at 12VDC rating to your circuit.