Bluewater Mid-Range 50A Panel Mount Circuit Breaker
Bluewater Mid-Range 50A Panel Mount Circuit Breaker — Product description
The Bluewater Mid-Range 50A Panel Mount Circuit Breaker protects moderate-load DC circuits from overloads and short circuits. It's rated for 12 to 32V DC with up to 2500A interrupting capacity, and it's built for boat and RV electrical panels.
A breaker is the one part of your boat's wiring you hope never gets tested. When something goes wrong, a chafed wire, a shorted pump, a corroded connection, this is the part that decides whether you lose a circuit or lose a lot more. The Bluewater Mid-Range 50A Panel Mount Circuit Breaker is built for that job on moderate-load DC circuits, and it's the kind of part you install once and don't think about again.
It carries a 50 amp rating and protects against both overload and short circuits. It's compatible with 12 to 32V DC systems, so it works on a 12V center console, a 24V cruiser, or the house side of an RV or mobile rig. Bluewater positions the Mid-Range line for auxiliary and accessory circuits, and that's where a 50A breaker earns its keep. Think bilge and livewell pump banks, a windlass feed on a smaller boat, a bus bar feed for a block of accessories, or an inverter or charger branch sized to match.
The interrupting capacity is up to 2500A. That number matters more than most people realize. If a dead short happens close to a big battery bank, the breaker has to open that fault safely, not weld itself shut. A rating of 2500A gives you a solid margin on the kind of 12V and 24V systems this breaker is meant for. It's still worth checking your own battery bank's available short-circuit current if you run a large lithium setup, since those can push a lot of current.
The housing is thermoplastic, and the internal components are nickel-plated copper. Nickel plating helps the conductive parts stand up to the moisture, salt air, and vibration that wear down bare copper over a season or two. Bluewater rates it as marine grade, so it's designed for boats, and it's equally at home in RV and mobile electrical systems where bumps and road shake are the daily routine.
Installation is straightforward. This is the panel mount version, so it sets into a panel cutout and connects with #10 ring terminals. If you'd rather mount it on a flat surface instead of a panel, Bluewater makes surface mount versions of the Mid-Range breaker too, and those are a separate item. Ring terminals aren't included with the breaker, so grab a crimp-on set sized for your wire and use a proper crimper. A good crimp with adhesive-lined heat shrink is worth the extra minute.
Sizing a breaker comes down to the wire, not the load. The breaker's job is to protect the conductor, so pick a wire gauge that safely carries at least 50 amps for the length of your run, and check it against a current ABYC ampacity table. If your actual load is much smaller than 50 amps, don't force a 50A breaker onto thin wire. Use a lower-rated breaker that matches the cable. We're happy to help you sort that out before you order.
Place the breaker as close to the power source as practical, on the positive side, with the wire between the battery and the breaker kept short and well supported. Keep the terminals clean and tight, and re-check them after the first few trips on the water, because connections that settle in are the ones that cause trouble later.
This breaker isn't meant for AC circuits, and it isn't a fit for very high current feeds like a big bow thruster or a main battery feed. Those need heavier protection rated for the load. For everyday DC accessory circuits at up to 50 amps, though, it's a clean, dependable way to protect your wiring and keep the circuit easy to isolate and service. Match it to your wire, crimp your terminals well, and it'll do its job quietly for years.
Key Features
- 50 amp rating gives overload and short-circuit protection for moderate-load DC circuits.
- 12 to 32V DC compatible, so it works on 12V and 24V boat systems and RV or mobile setups.
- Interrupting capacity up to 2500A for dependable short-circuit protection.
- Thermoplastic housing with nickel-plated copper components built for vibration, moisture, and marine conditions.
- Panel mount design sets cleanly into a panel cutout.
- Connects with #10 ring terminals, which you'll want to crimp and seal properly.
- Part of the Bluewater Mid-Range line, with surface mount versions sold separately.
- Suited to auxiliary and accessory circuits like pump banks, bus feeds, and charger branches.
Why Buy from NVN Marine
- Authorized Bluewater reseller, full manufacturer warranty
- NMEA member and ABYC certified, advice from real boat techs
- Same-day shipping before 3 PM ET on in-stock items
- NY headquarters and Fort Lauderdale flagship retail store
Technical specifications
| Title | Bluewater Mid-Range 50A Panel Mount Circuit Breaker |
|---|---|
| Brand | Bluewater |
| Manufacturer Part Number | 78000-9600-50 |
| UPC | 810196332386 |
| Product Line | Mid-Range |
| Current Rating | 50A |
| Max Voltage | 32V DC |
| Voltage Compatibility | 12 to 32V DC |
| Interrupting Capacity | Up to 2500A |
| Mounting | Panel mount |
| Housing Material | Thermoplastic |
| Component Material | Nickel-plated copper |
| Terminals | #10 ring terminal |
| Protection Type | Overload and short-circuit |
| Category | Electrical |
Frequently asked questions
What amp rating is this breaker?
It's a 50 amp breaker, listed as 50A in the Bluewater Mid-Range line (model 78000-9600-50).
What voltage can I use it on?
It's rated for a maximum of 32V DC and is compatible with 12 to 32V DC systems. That covers 12V and 24V boat systems as well as RV and mobile electrical setups.
Can I use it on an AC circuit?
No. The ratings published for this breaker are DC only, so don't use it for AC circuits.
What's the interrupting capacity?
Up to 2500A, which is the level of short-circuit current the breaker is designed to interrupt.
What terminals does it use?
It connects with #10 ring terminals. They're not part of the breaker listing, so plan to buy ring terminals sized for your wire.
Is this a panel mount or surface mount breaker?
This one is the panel mount version. Bluewater also makes surface mount versions of the Mid-Range breaker, and those are separate products.
What is it made of?
The housing is thermoplastic, and the internal components are nickel-plated copper.
What kinds of circuits is a 50A Mid-Range breaker meant for?
Bluewater designed the Mid-Range line for moderate-load DC systems such as auxiliary and accessory circuits. Always size the breaker to protect the wire in that circuit.
Is it marine grade?
Yes. Bluewater describes it as marine grade and built to withstand vibration, moisture, and harsh marine environments.
How do I choose the right breaker size?
Size it to protect the wire. Choose a wire gauge that safely carries at least 50 amps for your run length, check an ABYC ampacity table, and if your wire is smaller, step down to a lower-rated breaker.