Blue Sea C-Series Flat Rocker Breaker, Triple Pole 100A AC
Blue Sea C-Series Flat Rocker Breaker, Triple Pole 100A AC — Product description
The Blue Sea Systems C-Series Flat Rocker Circuit Breaker, Triple Pole 100A AC, is a 120/240 volt AC main that switches both hots and the neutral together. It's a trip free magnetic hydraulic design with 5,000 amperes of interrupt capacity, built for shore power and generator mains.
Your AC main is the one breaker you never want to think about on the water. It sits between your shore power or generator and everything else on the boat, so it has to trip cleanly when something goes wrong and stay out of the way when nothing does. This Blue Sea Systems C-Series Flat Rocker Circuit Breaker, model 7568-BSS, is a triple pole 100 amp AC breaker built for exactly that job.
Here's why the pole count matters. The triple pole version can be used as a 240 volt AC main, switching both lines (the hots) and the neutral at the same time. The double pole version in this family can serve as a 120 volt AC main by switching the hot and the neutral. Same idea, different pole count for a different electrical setup. Before you order, confirm which one matches your boat's AC system. This listing is the triple pole, 100A AC breaker.
It's a magnetic hydraulic breaker, and it's trip free. That second part is the one to remember. A trip free design can't be held in the ON position while fault current is flowing, so nobody can defeat the protection by leaning on the rocker. And if any one pole trips, the breaker trips all of its poles. You won't end up with a half-tripped breaker and one pole still closed.
Now the numbers. Blue Sea specifies 5,000 amperes of interrupt capacity to meet ABYC requirements for 120/240 volt main protection. The spec sheet lists it as 5000A @ 48V DC. The operating temperature range runs from -40 deg C to 85 deg C, so a cold, unheated engine room in January and a hot bilge compartment in August both sit inside the rating. The flat rocker actuator gives you a clear ON and OFF position right at the panel.
Installation is where people get tripped up, so let's be direct. The terminals are 1/4-20 tin-plated brass studs. Torque them to 35 in-lb (3.95 Nm). The mounting screws are 6-32 stainless steel, and they want 6 in-lb (0.68 Nm). Don't guess on either number. A loose lug on a 100 amp feed is the classic failure point, and it's not the breaker's fault. A few seconds with a torque driver prevents it.
Size everything around the breaker for 100 amps. That means the cable, the lugs, the shore power inlet, and the panel bus. The breaker can only protect the circuit if the rest of the circuit is rated for the same current. And before you touch a single wire, shut off shore power, shut down the generator, and confirm the conductors are dead with a meter. AC mains aren't forgiving.
If it trips, find out why before you reset it. A breaker that opens on a fault is doing its job, so treat the trip as information. Check the load, check the connections, and check for heat at the terminals. Then reset. Repeatedly slamming it back on without finding the cause is how small problems turn into big ones.
This breaker is rated for 10000 switching cycles, which is a long service life for a main you'll flip at the dock a handful of times a month. It weighs 0.93 lb (0.42 kg), so it's not adding much to the panel.
It's a good fit for larger cruisers and sportfishers with big shore power or generator feeds, the kind of boat where a single 30 amp inlet won't cover the load. It isn't a DC battery breaker, and it doesn't replace an ELCI or other ground fault protection your AC system calls for. If you're not sure how your AC system is laid out, have a qualified marine electrician look at it first. Wiring an AC main isn't a casual weekend project. Do it once, do it right, and you won't think about it again.
Key Features
- Triple pole, 100A AC rating, so it can serve as a 240 volt main switching both hots and the neutral
- Magnetic hydraulic, trip free design that can't be held ON during a fault current condition
- Trips all poles if any one pole trips, so no half-tripped breaker
- 5,000 amperes of interrupt capacity to meet ABYC requirements for 120/240 volt main protection
- 1/4-20 tin-plated brass terminal studs, torqued to 35 in-lb (3.95 Nm)
- 6-32 stainless steel mounting screws, torqued to 6 in-lb (0.68 Nm)
- Operating temperature from -40 deg C to 85 deg C for cold and hot machinery spaces
- Rated for 10000 switching cycles
Why Buy from NVN Marine
- Authorized Blue Sea Systems reseller, full manufacturer warranty
- NMEA member and ABYC certified, advice from real boat techs
- Same-day shipping before 3 PM ET on in-stock items
- NY headquarters and Fort Lauderdale flagship retail store
Technical specifications
| Title | Blue Sea C-Series Flat Rocker Circuit Breaker Triple Pole 100A AC |
|---|---|
| Brand | Blue Sea Systems |
| Manufacturer Part Number | 7568-BSS |
| UPC | 632085075682 |
| Amperage | 100A AC |
| Actuator Style | Flat Rocker |
| Poles | 3 |
| Maximum Voltage | 120V AC / 240V AC |
| Circuit Breaker Type | Magnetic Hydraulic, trip free |
| Terminal Stud | 1/4-20 Tin-Plated Brass |
| Terminal Stud Torque | 35 in-lb (3.95 Nm) |
| Interrupt Capacity | 5000A @ 48V DC |
| Minimum Operating Temperature | -40 deg C |
| Maximum Operating Temperature | 85 deg C |
| Mounting Screw | 6-32 Stainless Steel |
| Mounting Screw Torque | 6 in-lb (0.68 Nm) |
| Switching Cycles | 10000 |
| Weight | 0.93 lb (0.42 kg) |
Frequently asked questions
What is the Blue Sea 7568-BSS?
It's a C-Series flat rocker circuit breaker, triple pole, rated 100A AC. It's used as a 120/240 volt AC main circuit breaker.
What voltage is it rated for?
The maximum voltage is listed as 120V AC / 240V AC.
Can I use it as a 240 volt main?
Yes. Blue Sea says the triple pole version can be used as a 240 volt AC main circuit breaker to switch both lines (the hots) and the neutral.
Does it trip all poles if one pole trips?
Yes. Blue Sea states the breaker will trip all poles if any one pole trips.
What does trip free mean?
A trip free design can't be held ON during a fault current condition. If there's a fault, the breaker opens and stays open.
What is the interrupt capacity?
Blue Sea specifies 5,000 amperes of interrupt capacity to meet ABYC requirements for 120/240 volt main protection. The spec sheet lists 5000A @ 48V DC.
What type of breaker is it?
It's a magnetic hydraulic breaker with a trip free design.
What size terminal studs does it use, and how tight should they be?
The terminals are 1/4-20 tin-plated brass studs. Torque them to 35 in-lb (3.95 Nm).
What are the mounting screw size and torque?
The mounting screws are 6-32 stainless steel. Torque them to 6 in-lb (0.68 Nm).
What temperature range can it handle?
The operating temperature range is -40 deg C to 85 deg C.
How many times can it be switched?
It's rated for 10000 switching cycles.
How much does it weigh?
It weighs 0.93 lb (0.42 kg).